Intended Usage; Electrical Safety; Operating Safety - LYSON Optima Manual

Prior to device usage initiation, refer to the following
manual and act according the guidelines contained
therein. The manufacturer shall not be held
accountable for any damages caused by improper
usage of the device or its improper handling.

INTENDED USAGE

The device is intended for honey filling,
pumping and creaming.

ELECTRICAL SAFETY

a) The device shall be connected to a plug with grounding
with the voltage specified on the product nominal plate
b) Power supply electric installation must be equipped
with RCD with nominal tripping current below 30 mA.
Periodically check the RCD.
c) Periodically check the power supply cable. If non-
detachable power supply cable gets damaged and
must be replaced, it must be performed at a guarantor's
or by a specialised repair centre or by a qualified
person in order to avoid any threat.
d) Do not operate the device when the power supply
cable is damaged.
e) Periodically check the power supply cable. If a
detachable power supply cable gets damaged, it must
be replaced with the cable of the same type. Do not
operate the device when the power supply cable is
damaged

OPERATING SAFETY

a) The following equipment is not intended to be used by
persons with limited physical, sensory or mental
capabilities (including children) or persons
inexperienced or unfamiliar with that type of equipment
unless the usage occurs under supervision or in line
with the equipment operating manual provided by
safety supervising persons. Make sure that children do
not play with the device.
If the device cable gets damaged, the repairs must be
b)
performed solely by a specialised repair centre or by a
qualified person in order to avoid any threat
c) Do not operate the device in the vicinity of
flammable materials.
d) It is forbidden to perform any
maintenance works when the device is in
operation.
e) In case of any danger, switch the device off
immediately.
The device can be restarted once the threat has been
f)
eliminated.
g) The device can be activated indoors only. The device is
not adjusted to be operated outdoors.
h) Protect the controller against humidity; (also
during the storage) It is forbidden to pull the
supply cable.
It is forbidden to pull the supply cable.
i)
The supply cable ought to be kept away from the
j)
sources of heat, sharp edges and its good state must
be taken care of.
ATTENTION!
Honey intended for dozing ought to be heated until
the temp. of approximately 30°C
IN ORDER TO SEAL THE DOZING MODULE, IT
MUST BE SUBMERGED IN HONEY PRIOR TO
OPERATION
Required minimal temperatures for honey:
•
Freshly extracted honey, liquid :20 - 25
•
Heather honey, cream honey or honey with little
water content, approx. <16% : 25-35
•
Maximum temperature for filled honey is MAX
°
40 C
Failure to observe
recommendations may result in the device
damage, for which the manufacturer is not to be
held accountable. The product damaged due to
misuse is excluded from the guarantee provisions.
Guidelines:
1. Connect the hose to the dozing module by
means of a clamp, watch the proper position
of the gasket. .
2. Afterwards, pour approximately 1 kg of honey to the
other end of the hose (i.e. a jar of 0.95 kg).
3. Keep the connection hose upwards until the honey
flows down to the (pump) rotor
The connection hose is transparent so it is
visible when
.
Before pressing the START button,
CREAMING function must be activated.
When the honey has reached the pump
„START"
the green button to the right of the display
4. One must remember to put a honey jar under the
pump (dispenser)
When the previously poured honey has been
5.
pumped entirely, stop the pump by pressing the
STOP button
6. Having completed the aforementioned activities, put
the dispenser connecting hose to a barrel of honey
and start dozing or pumping.
A small quantity of honey must be pumped to
7.
remove the air that stayed in the hose.
8. The dispenser is then read for operations at this
stage.
°C
°C
the honey temperature
honey has reached the pump.
button must be pressed .
2