The ELAN Training Guide contains valuable hardware and software reference documentation and is considered an important supplement to this document. Make sure you have the latest version by visiting the ELAN Dealer website at www.elanhomesystems.com and follow the Dealer Resources link.
Page 3
EL-SC-100 FCC and IC Information: This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-003 and RSS-247. Operation is subject to the following two conditions: 1. This device may not cause interference and 2.
QUICK INSTALL GUIDE Warning: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Product Solutions Group at Tel: (519) 763-4538. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for...
Page 5
EL-SC-100 La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite ‘exposition aux fréquences radio d’Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d’exposition aux RF d’IC dans des conditions d’exposition à...
Page 6
QUICK INSTALL GUIDE EL-SC-100 Overview Dimensions: 6.95 in. x 4.94 in. x 1.30 in. Power Status Button Indicator Reset IR OUTPUTS AUDIO SENSE LAN/POE RS-232 RS-232 IR Outputs DC Power LAN / PoE Audio Out Sense Input EL-SC-100_Rear_01.ai EL-SC-100_Rear_01.ai...
Page 7
EL-SC-100 Mounting The EL-SC-100 is designed to mount on a shelf, hang in a cabinet or rack, or mount in a structured wiring enclosure with optional mounting bracket. Wall Mounting: The EL-SC-100 chassis has been designed to allow convenient wall mounting in any orientation. Arrows on the rear panel may be used to mark the location for the screws.
Page 8
QUICK INSTALL GUIDE Using the optional Structured Structured Wiring Cabinet Mounting: Wiring Cabinet Mount, the EL-SC-100 can be mounted in a structured wiring cabinet. 1. Attach mounting bracket to wiring cabinet with snap rivets and washers 2. Snap the controller to the 2 hooks on the mounting bracket...
Connect an RS-232 serial controlled device using an RJ45 connector (not included) to the RS232 port on the rear of the controller. The EL-SC-100 serial connector is not compatible with RS-485 serial devices. If your project requires RS-485 connections you will need to use a gSC10 controller.
Page 10
ELAN sensors can be used to trigger events from 3rd party devices. The status is binary, either ON or OFF. This can be used to trigger an event map or as a condition of an event map. CONNECT ONLY an ELAN sensor to this port.
EL-SC-100 HDMI Connection The EL-SC-100 includes an HDMI connector for an on screen display (OSD) interface. Connect the OSD output to an available HDMI input on a display or AVR USB Connection The USB connection is primarily designed for connecting the optional USB Z-Wave antenna.
QUICK INSTALL GUIDE Power Once all other connections have been completed, connect an Ethernet cable connected to a PoE switch or the 12 VDC, 1A power supply to the DC input. Power Button When the controller is off, a short press powers unit on When the controller is on, a short press (less than three seconds) restarts controller.
EL-SC-100 Network Connection The EL-SC-100 is factory set to use DHCP. Connect to a wired network and use the ELAN Configurator to connect to the controller. Once connected, use configurator to set a static IP address or connect via WiFi.
Limited Warranty Nortek Security & Control ( ‘NSC’ ) warrants the EL-SC-100 to be free from defects in materials and workmanship for the period of two years (2 years) from the date of purchase. If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly notifies ‘NSC’...