Advertisement
Quick Links
MAX VEHICLE ROOF LOAD RATINGS:
100 KG PRADO 120/150
150 KG LANDCRUISER 200
•
Please read instructions carefully before installation.
•
Check the contents of kit. Contact your YAKIMA dealer if any parts appear missing or damaged.
•
Clean your roof thoroughly prior to fitting the LockNLoad Heavy Duty Roof Rack System.
•
Place these instructions in the vehicle's glove box after installation is complete.
TOOLS REQUIRED:
•
13 mm Socket Wrench
•
13 mm Spanner
•
10 mm Open Ended Spanner
•
#2 Phillips Head Screwdriver
• Torque Wrench (Optional)
•
Rubber Mallet (Optional)
• Tape Measure
•
Scissors
•
Spirit Level
ITEM COMPONENT
1.
M6 Washer
2.
M6 Set Screw 30 mm
3.
M8 Washer
4.
M8 Hex Bolt 40 mm
5.
Foam Adhesive
LEG AND BAR COMPONENTS SOLD SEPARATELY
1
2
28-13-004-Rev4
®
TOYOTA PRADO 120/150 SERIES, LANDCRUISER 200 SERIES
2 BAR FIXED POINT HEAVY DUTY ROOF RACK SYSTEM
TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO
FIRST TIME INSTALLATION
KIT CONTENTS
QTY ITEM
x4
x4
x8
x8
x8
7
LockNLoad Mounting Kit
COMPONENT
6.
Front Left Pad (2804013)
7.
Rear Left Pad (2804014)
8.
Front Right Pad (2804016)
9.
Rear Right Pad (2804017)
6
9
™
8
5
QTY
x1
x1
x1
x1
3
4
1/8
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Yakima LockNLoad 8000312
Summary of Contents for Yakima LockNLoad 8000312
- Page 1 • Please read instructions carefully before installation. • Check the contents of kit. Contact your YAKIMA dealer if any parts appear missing or damaged. • Clean your roof thoroughly prior to fitting the LockNLoad Heavy Duty Roof Rack System. •...
-
Page 2: Installation
INSTALLATION REMOVE FIXED POINT HARDWARE AFFIX FOAM ADHESIVE Remove fixed-point covers. Place Foam Adhesive over Remove bolts, washers plastic tubes and brackets from the in the vehicle’s vehicle’s fixed points. fixed points, with adhesive Store items away in side to vehicle. a safe place. - Page 3 SECURE PADS TO FIXED POINTS Tighten all M8 Hex Bolts to 7 Nm using 13 mm Socket Wrench. Check Assemble 1 x M8 Washer onto all Bolts are completely tightened each M8 Hex Bolt 40 mm as down and secure as required. shown.
- Page 4 REMOVE LEG COVERS INSERT LEGS Using the keys supplied Slide the pre-assembled Leg in the LockNLoad Leg assemblies into the underside channel Kit (sold separately), of LockNLoad Bars. remove all Leg Covers. If Leg assemblies will not slide in, loosen Screws to increase gap.
- Page 5 BAR SLOT COVERS (OUTSIDE LEG) Measure the Bar channel outside of the Legs and subtract 20 mm from this measurement. Using the remaining pieces of Slot Cover from Step 9, cut to this length and insert into the underside channel of each Bar end as shown. -20 mm Secure using Plastite Screw SECURE END CAPS TO BARS...
- Page 6 SECURE BARS TO PADS Tighten all M6 set screws to 7 Nm using 10 mm Open Ended From the LockNLoad Mounting kit, Spanner. assemble 1 x M6 Washer onto each M6 set screw 30 mm as shown. Insert Do not over tighten. through the centre hole on Leg into Pad.
- Page 7 Write the key number (which is stamped on the key) in the box provided. Replacement keys are available from Yakima stockists, visit www.yakima.com.au or www.yakima.co.nz to find your nearest store or contact us directly on 1800 143 548 (AU) or 0800 4776 722 (NZ). Key Number:...
- Page 8 YAKIMA AUSTRALIA PTY. LTD 17 Hinkler Court Brendale, QLD 4500 Australia 1800 143 548 YAKIMA PRODUCTS, INC. 4101 Kruse Way Lake Oswego, OR 97035-2541 888 925 4621 28-13-004-Rev4...
Need help?
Do you have a question about the LockNLoad 8000312 and is the answer not in the manual?
Questions and answers