Dell OptiPlex 3020M Owner's Manual
Dell OptiPlex 3020M Owner's Manual

Dell OptiPlex 3020M Owner's Manual

Hide thumbs Also See for OptiPlex 3020M:
Table of Contents

Advertisement

Quick Links

Dell OptiPlex 3020M
Owner's Manual
Regulatory Model: D08U
Regulatory Type: D08U001

Advertisement

Table of Contents
loading

Summary of Contents for Dell OptiPlex 3020M

  • Page 1 Dell OptiPlex 3020M Owner's Manual Regulatory Model: D08U Regulatory Type: D08U001...
  • Page 2 Copyright © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. Dell ™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies. Rev. A02...
  • Page 3: Table Of Contents

    Installing the Dell OptiPlex Micro VESA Mount........................10 Installing the Dell OptiPlex Micro Vertical Stand.......................11 Installing the Dell OptiPlex Micro Console with DVD-RW....................11 Installing the Dell OptiPlex Micro All-in-One Mount Behind the Monitor..............15 List of Compatible Monitor Models...........................20 3 Extracción e instalación de componentes..................22 Front and Back View................................22...
  • Page 4 Contraseña del sistema y de configuración........................41 Asignación de contraseña del sistema y de configuración..................41 Eliminación o modificación de una contraseña del sistema y de configuración existente........42 Desactivación de la contraseña del sistema....................... 42 5 Specifications..........................44 6 Contacting Dell.......................... 47 Contents...
  • Page 5: Manipulación Del Equipo

    Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
  • Page 6: Turning Off Your Computer

    2. Connect any telephone or network cables to your computer. 3. Connect your computer and all attached devices to their electrical outlets. 4. Turn on your computer. 5. If required, verify that the computer works correctly by running the Dell Diagnostics. Manipulación del equipo...
  • Page 7: Installing The Accessories

    Installing the Dell OptiPlex Micro Vertical Stand • Installing the Dell OptiPlex Micro Console with DVD-RW • Installing the Dell OptiPlex Micro All-in-One Mount Behind the Monitor • List of Compatible Monitor Models Installing the Power Adapter 1. Perform the following steps as shown in the illustration: a) Slide to open the cover of the power adapter [1].
  • Page 8: Installing The Dell Optiplex Micro Dual Vesa Mount

    Installing the Dell OptiPlex Micro Dual VESA Mount Recommended Screws: Screw Type Used in M4 x L10 mm, Pan head screw Monitor Prerequisite: Install the power adapter. 1. Align the dual VESA mount behind the monitor and tighten the screws to secure the dual VESA mount to the monitor.
  • Page 9 3. Slide the power adapter case through the grooves at the bottom of the dual dual VESA mount to lock it. 4. Connect all the cables and antenna to the computer. Installing the Accessories...
  • Page 10: Installing The Dell Optiplex Micro Vesa Mount

    5. Tighten the screws to secure the arm stand to the dual VESA mount. Installing the Dell OptiPlex Micro VESA Mount Recommended Screws: Screw Type Used in M4 x L10 mm, Pan head screw Monitor ST4 x L13 mm, Wooden screw Wooden table Prerequisite: Install the power adapter.
  • Page 11: Installing The Dell Optiplex Micro Vertical Stand

    Connect all the cables and install antenna to the computer. Installing the Dell OptiPlex Micro Vertical Stand Align the computer on the vertical stand and ensure the tab on the vertical stand fits into the groove or notch on the system.
  • Page 12 2. Perform the following steps as shown in the illustration: a) Slide the computer into the slot [1]. b) Tighten the screw to secure the computer to the optical drive console [2]. 3. Perform the following steps as shown in the illustration: a) Cut the strap of the power adapter cable [1].
  • Page 13 4. Perform the following steps as shown in the illustration: a) Open the cable management clip [1]. b) Lift the antenna cable out [2]. c) Connect the antenna cable to the antenna connector [3]. 5. Route the USB cables through the cable management clip and connect them to the computer. Close the cable management clip. Installing the Accessories...
  • Page 14 6. Perform the following steps as shown in the illustration: a) Prepare the wooden table by installing screws for mounting the optical drive console. b) Align the slots on the optical drive console with the screws on the table and slide the optical drive console and lock it. c) Tighten the screws to secure the optical drive console to the wooden table.
  • Page 15: Installing The Dell Optiplex Micro All-In-One Mount Behind The Monitor

    8. Perform the following steps as shown in the illustration: a) Slide and insert the cover to its position [1]. b) Tighten the screws to secure the cover to the chassis [2]. Installing the Dell OptiPlex Micro All-in-One Mount Behind the Monitor Recommended Screws:...
  • Page 16 M4 X L8 mm, pitch 0.5 mm, machine screw PUZ plate with thread screw holes — Dell P,U,PU,UZ- series monitors M3 X L8 mm, pitch 0.5 mm, self-tapping E Plate without thread screw holes— Dell screw E-series monitors M3 X L8 mm, pitch 0.35 mm, machine E Plate with thread screw holes—...
  • Page 17 2. Perform the following steps as shown in the illustration: a) Slide the computer into the slot [1]. b) Rotate the screw in clockwise direction to secure the computer to the chassis [2]. 3. Perform the following steps as shown in the illustration: a) Lift up the antenna cable [1].
  • Page 18 4. Perform the following steps as shown in the illustration: a) Cut the strap of power adapter cable [1]. b) Slide the power adapter into the slot [2]. c) Route the cable through the clip [3]. 5. Perform the following steps as shown in the illustration: a) Route the cable through the clip [1].
  • Page 19 6. Align the PUZ plate to the bottom of monitor and tighten the screws. 7. Perform the following steps as shown in the illustration: a) Slide and lock the chassis to the PUZ plate [1]. b) Rotate the screw in clockwise direction to secure the computer [2]. c) Flip the computer along with the monitor [3].
  • Page 20: List Of Compatible Monitor Models

    8. Perform the following steps as shown in the illustration: a) Connect all the cables to the computer. b) Slide the cover to its original position [1]. c) Tighten the screws to secure the cover to the chassis [2]. List of Compatible Monitor Models E-Plate P/U-Plate and UZ-Plate U-Plate...
  • Page 21 E-Plate P/U-Plate and UZ-Plate U-Plate E2414H UP3214Q E2715H UZ2215H UZ2315H UZ2715H S2415H S2715H Installing the Accessories...
  • Page 22: Extracción E Instalación De Componentes

    Extracción e instalación de componentes Front and Back View Figure 1. Front and Back View 1. power button or power light 2. hard-drive activity light 3. headset connector 4. microphone connector 5. Wi-Fi antenna connector (optional) 6. serial and PS2 connector (optional) 7.
  • Page 23: Installing The Cover

    3. Perform the following steps as shown in the illustration: a) Remove the screw that secures the cover to the computer [1]. b) Slide the cover outwards [2]. c) Lift the cover up to remove it from the computer [3]. Installing the Cover 1.
  • Page 24: Installing The Processor Fan Module

    4. Disconnect the speaker and fan cables from the system board. Installing the Processor Fan Module 1. Connect the speaker and fan cable to the connectors on the system board. 2. Place the processor fan module on the slot and slide it until it is secured. 3.
  • Page 25: Installing The Speaker

    NOTE: The speaker is a part of the processor fan module. Installing the Speaker 1. Place and align the speakers on the processor fan module. 2. Tighten the screws to secure the speaker to the processor fan module. 3. Thread the cables through the cable clips to secure it. 4.
  • Page 26: Installing The Hard Drive

    4. Perform the following steps as shown in the illustration: a) Pry the hard-drive bracket apart to release the hard drive [1]. b) Lift the hard drive away from hard-drive bracket [2]. Installing the Hard Drive 1. Insert the hard drive into the hard-drive bracket. 2.
  • Page 27: Installing The Heatsink

    b) Lift the heatsink away from the system board [2]. Installing the Heatsink 1. Place the heat sink on the system board. 2. Tighten the screws to secure the heatsink. 3. Install: processor fan module cover 4. Follow the procedures in After Working Inside Your Computer.
  • Page 28: Removing The Wlan Card

    3. Connect the cable to the PS2 and serial connector board. 4. Install the cover. 5. Follow the procedures in After Working Inside Your Computer. Removing the WLAN Card 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: cover hard drive 3.
  • Page 29: Installing The Processor

    Installing the Processor 1. Insert the processor into the processor socket. Ensure that the processor is properly seated. 2. Press the release lever down and then move it inward to secure it with the retention hook. 3. Install the: hard drive cover 4.
  • Page 30: Installing The Coin-Cell Battery

    Installing the Coin-Cell Battery 1. Place the coin-cell battery into its slot on the system board. 2. Press the coin-cell battery downward until the release latch springs back into place and secures it. 3. Install the: PS2 and serial connector board hard drive cover 4.
  • Page 31 cover processor fan module hard drive heatsink memory processor PS2 or serial connector board WLAN card coin-cell battery 3. Perform the following steps as shown in the illustration. a) Remove the screws that secure the hard-drive holder to the system board [1]. b) Lift the hard drive holder away from the system board [2].
  • Page 32: Installing The System Board

    Installing the System Board 1. Place the system board on the computer. 2. Tighten the screws to secure the system board to the base panel. 3. Place the hard drive holder on the system board. 4. Tighten the screws that secure the hard-drive holder to the system board. 5.
  • Page 33: Configuración Del Sistema

    La secuencia de arranque le permite omitir el orden de dispositivos de arranque definido en la configuración del sistema y arrancar directamente desde un dispositivo específico (por ejemplo, la unidad óptica o la unidad de disco duro). Durante la autoprueba de encendido (POST), cuando aparezca el logotipo de Dell, puede hacer lo siguiente: •...
  • Page 34: System Setup Options

    Teclas Navegación <Tab> Se desplaza a la siguiente área de enfoque. NOTA: Solo para el explorador de gráficos estándar. <Esc> Se desplaza a la página anterior hasta que vea la pantalla principal. Si presiona la tecla <Esc> en la pantalla principal, aparecerá...
  • Page 35 Option Description Serial Port Identifies and defines the serial port settings. This option appear only if your system installed serial port card. You can set the serial port to: • Disabled • COM1 (Default) • COM2 • COM3 • COM4 NOTE: The operating system may allocate resources even if the setting is disabled.
  • Page 36 Table 5. Security Option Description Admin Password Allows you to set, change, or delete the administrator (admin) password. NOTE: You must set the admin password before you set the system or hard drive password. Deleting the admin password automatically deletes the system password and the hard drive password.
  • Page 37 Option Description • On-Silent Default Setting: Disabled CPU XD Support Allows you to enable or disable the execute disable mode of the processor. • Enable CPU XD Support - This option is enabled by default. Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin password is set. •...
  • Page 38 Option Description Limit CPUID Value This field limits the maximum value the processor Standard CPUID Function will support. • Enable CPUID Limit - This option is not set by default. NOTE: Some Operating system will not complete installation when the maximum CPUID Function is greater than 3.
  • Page 39 Option Description Default setting: Disabled Table 9. POST Behavior Option Description Numlock LED Specifies if the NumLock function can be enabled when the system boots. This option is enabled by default. Keyboard Errors Specifies whether keyboard related errors are reported when it boots. This option is enabled by default.
  • Page 40: Actualización De Bios

    1. Vuelva a iniciar el equipo. 2. Vaya a dell.com/support. 3. Escriba la Service Tag (etiqueta de servicio) o Express Service Code (código de servicio rápido) y haga clic en Submit (enviar).
  • Page 41: Jumper Settings

    11. Haga clic en Save (Guardar) para guardar el archivo en su equipo. 12. Haga clic en Run (ejecutar) para instalar las configuraciones del BIOS actualizado en su equipo. Siga las instrucciones que aparecen en pantalla. Jumper Settings To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s) indicated on the system board. The following table displays the system board jumper settings.
  • Page 42: Eliminación O Modificación De Una Contraseña Del Sistema Y De Configuración Existente

    4. Introduzca la contraseña del sistema que especificó anteriormente y haga clic en OK (Aceptar). 5. Seleccione Setup Password (Contraseña de configuración), introduzca la contraseña del sistema y presione <Intro> o <Tab>. Aparecerá un mensaje para que introduzca de nuevo la contraseña de configuración. 6.
  • Page 43 13. Vaya a Configuración del sistema y asigne una contraseña del sistema o de configuración. Consulte Configuración de una contraseña del sistema. Configuración del sistema...
  • Page 44: Specifications

    Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) > Help and Support, and then select the option to view information about your computer. Table 16. Processor Feature Specification Processor type •...
  • Page 45 Table 23. Cards Feature Specification WLAN card Intel Dual Band Wireless-AC 7260 (M.2) 802.11 ac Bluetooth 4.0 WiDi (Wireless Display) NOTE: For optimal performance, it is recommended to use the wireless display feature with an access point that supports 5 GHz standard.
  • Page 46 Table 27. Power Items Wattage Voltage Power adaptor 65 W 19.5 VDC, 3.34 A Coin-cell battery 3 V CR2032 lithium coin cell Table 28. Physical Dimension Physical Micro Entry Height 18.2 cm (7.17 inches) Width 3.6 cm (1.42 inches) Depth 17.6 cm (6.93 inches) Weight 1.28 kg (2.82 lb)
  • Page 47: Contacting Dell

    Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: Go to Dell.com/contactdell.

Table of Contents