Page 2
Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Page 3
table of contents introduction hardware parts list how to use the cam lock system assembly 7-14 how to adjust door alignment QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
Page 4
hardware (H1) x 8 (H2) x 4 (H3) x 4 (H4) x 21 (H5) x 8 short pan head screw short flat head screw wooden dowel cam bolt (H6) x 4 (H7) x 2 (H8) x 2 (H9) x 1 (H10) x 1 shelf support knob...
Page 5
exploded diagram ITEM DESCRIPTION QUANTITY top panel left side panel right side panel bottom panel shelf panel left door right door back panel...
Page 6
how to use the cam lock system Screw cam bolt into panel Align cam bolt(s) with cross-bored Push cam into panel - arrow feature hole(s) and insert all the way until on cam top points to panel edge panels are flush Rotate cam(s) clockwise 180°...
Page 7
step 1: attach right side panel to bottom panel (H1) x 2 (H2) x 2 (H3) x 2 wooden dowel cam bolt 1.1. Carefully tap small wooden dowels into place in right side panel. Leave 1/2” of the dowels sticking out. 1.2.
Page 8
step 2: attach left side panel (H1) x 2 (H2) x 2 (H3) x 2 wooden dowel cam bolt 2.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out. 2.2. Screw-In cam bolts must be screwed down flush in left side panel. 2.3.
Page 9
step 3: attach top panel (H4) (H1) x 4 (H4) x 2 (H9) x 4 (H10) x 1 wooden dowel short pan long flat magnet head screw head screw 3.1. Align short pan head screws with pre-drilled holes to attach magnet to top panel. Do not over tighten screws. Align short pan head screws with pre-drilled holes to attach magnet to top panel.
Page 10
step 4: attach back panel step 4. **FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT** pre-drilled holes Hole for anti-tip kit. Begin by installing all of the screws along one edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is square.
Page 11
step 5: attach knobs to doors (H7) x 2 (H8) x 2 knob knob bolt 5.1. Align knob bolts with pre-drilled holes to attach knobs to doors. Do not over tighten bolts.
Page 12
step 6: attach doors to cabinet (H5) x 8 short flat head screw 6.1. Align short flat head screws with pre-drilled holes to attach doors to cabinet. Do not over tighten screws. Align short flat head screws with pre-drilled holes to attach doors to cabinet. Do not over tighten screws.
Page 13
step 7: install adjustable shelves (H6) x 4 shelf support 7.1. Insert shelf supports into desired hole. Different holes accomodate different shelf heights. 7.2. Angle shelves to fit between the rails and set on top of shelf supports.
Page 14
step 8: install anti-tip kit (H13) (H15) (H12) Position against wall (H14) Mark position of strap hole on Mark position of strap hole on wall wall Drill 1/4’’ hole Tap in wall anchor Fasten anti-tip strap Fasten anti-tip strap with flat-head screw provided with flat-head screw provided (H11) (H15)
Page 15
how to adjust door alignment Tips for proper door alignment: -Adjustable levelers will reduce minor door mis-alignments caused by an uneven floor. -Use a level to determine if the cabinet top is level. If not, start with the levelers retracted and adjust them as needed.To retract the levelers turn them counterclockwise.
Page 16
50 lbs. inner shelf weight limit is 40 lbs. 1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury. 2.
Need help?
Do you have a question about the windham accent cabinet and is the answer not in the manual?
Questions and answers