Advertisement
Quick Links
Advertisement
Related Manuals for Feig Electronic PAN MOBIL ID PM ECCO+
Summary of Contents for Feig Electronic PAN MOBIL ID PM ECCO+
- Page 1 IDENTIFICATION USER GUIDE ID PM ECCO+ Compact and Robust RFID-/Barcode Scanner H90310-0e-ID-B...
- Page 2 Composition of the information in this document has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
- Page 3 IDENTIFICATION ID PM ECCO+ Contents Contents Contents Safety Instructions Revision History of Documentation Scope of Delivery Product Description Technical Data Operation Charging the Battery ....................... 12 Device Reset ........................12 Configuration ........................12 Scanning .......................... 13 6.4.1 1D Laser ......................13 6.4.2 1D/2D Imager .......................
- Page 4 IDENTIFICATION ID PM ECCO+ Contents 13.1 USA (FCC) and Canada (IC) .................... 22 13.2 Europe (CE) ........................23 Warranty Page 4 of 24...
- Page 5 IDENTIFICATION ID PM ECCO+ 1 Safety Instructions 1 Safety Instructions Safety Instructions ► Please read this user guide carefully and follow the given instructions and safety instructions before using the device. ► The device may only be used for the intended purpose designed by the manufacturer. ►...
- Page 6 IDENTIFICATION ID PM ECCO+ 1 Safety Instructions Observe restrictions on the use of radio devices in fuel depots, chemical plants and areas where the air ► contains chemicals or particles such as grain, dust or metal powder as well as any other area where you are advised to turn off your vehicle engine.
- Page 7 IDENTIFICATION ID PM ECCO+ 2 Revision History 2 Revision History of Documentation Revision History Revision Date Description 29.03.2019 Initial version Page 7 of 24...
- Page 8 IDENTIFICATION ID PM ECCO+ 3 Scope of Delivery 3 Scope of Delivery Scope of Delivery The scope of delivery includes following components: 1 x ID PM ECCO+ 1 x USB Charging Cable 1 x ID PM ECCO+ User Guide After unboxing please make sure, that all listed parts have been delivered properly and in good condition. Page 8 of 24...
- Page 9 IDENTIFICATION ID PM ECCO+ 4 Product Description 4 Product Description Product Description The ID PM ECCO+ captures and stores barcodes and RFID data for a variety of uses and transmits those to a host via USB connection, Bluetooth or WiFi. This document provides a basic instruction for using the ID PM ECCO+ device.
- Page 10 IDENTIFICATION ID PM ECCO+ 4 Product Description Key 3 (custom) (This function can be configured by using Master Setup or with the programming interface) Key 4 (custom) (This function can be configured by using Master Setup or with the programming interface) Power key to turn the unit ON.
- Page 11 IDENTIFICATION ID PM ECCO+ 5 Technical Data 5 Technical Data Technical Data Mechanical Data Housing Double-walled Inside: robust ABS Outside: protective rubber coating Dimension (W x H x D) 87 mm x 48 mm x 26 mm (3.42“ x 1.89“ x 1.02“) Weight 98 g (3.46 oz) Protection Class...
- Page 12 IDENTIFICATION ID PM ECCO+ 6 Operation 6 Operation Operation 6.1 Charging the Battery Before the first operation, the main battery should be fully charged by using the included USB charging cable. As long as the battery is charging the red LED (3) will light solid red. After the battery is fully charged the red LED (3) turns off.
- Page 13 IDENTIFICATION ID PM ECCO+ 6 Operation 6.4 Scanning 6.4.1 1D Laser To scan a barcode follow the steps below: Aim the scanner on the barcode. Press the trigger key (5). Ensure that the scanning line is directed straight on the barcode. The ID PM ECCO+ beeps and the yellow LED (2) lights up to indicate a successful decode.
- Page 14 IDENTIFICATION ID PM ECCO+ 6 Operation 6.4.2 1D/2D Imager To scan a barcode follow the steps below: Aim the scanner on the barcode. Press the trigger key (5). The ID PM ECCO+ decodes the barcode closest to the cross center unless you disable the Pick-List Mode (see below) in the 2D cameras.
- Page 15 IDENTIFICATION ID PM ECCO+ 7 Bluetooth Connection 7 Bluetooth Connection Bluetooth Connection To pair the Bluetooth enabled devices to a Bluetooth enabled host. Connect the device to the host using the USB port and use the Master Setup to set the data output mode to Bluetooth.
- Page 16 IDENTIFICATION ID PM ECCO+ 7 Bluetooth Connection 7.1 Numeric Barcodes for Bluetooth Pairing Page 16 of 24...
- Page 17 IDENTIFICATION ID PM ECCO+ 8 WiFi Connection 8 Wi-Fi Connection WiFi Connection To connect Wi-Fi enabled devices to a host. Connect the device to the host using the USB port and use the Master Setup to set the data output mode to Wi-Fi.
- Page 18 IDENTIFICATION ID PM ECCO+ 9 Transmitting Data to a Host 9 Transmitting Barcode and/or RFID Data to a Host Transmitting Data to a Host Batch mode All barcodes and RFID data scanned in batch mode are saved in the file “Output.txt” on the removable drive “SCANNDY”.
- Page 19 IDENTIFICATION ID PM ECCO+ 10 Troubleshooting 10 Troubleshooting Troubleshooting Problem Possible Solution Device does not turn on. Make sure the battery is charged. Laser comes on but device does not • Ensure the device is configured to read the type of code being scanned. decode barcode.
- Page 20 IDENTIFICATION ID PM ECCO+ 11 Maintenance and Cleaning 11 Maintenance and Cleaning Maintenance and Cleaning To clean the lense use a clean and dry cleaning cloth. Do not use chemical cleaners, lyes or similar. Page 20 of 24...
- Page 21 IDENTIFICATION ID PM ECCO+ 12 Disposal 12 Disposal Disposal Never dispose of Li-Ion batteries in household waste! Li-Ion batteries can be disposed of at special collection points. Before disposal, make sure that the Li-Ion battery is completely discharged. Page 21 of 24...
- Page 22 NOTE: Changes or modifications made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. Page 22 of 24...
- Page 23 This equipment is intended to be commercialized in all the countries of the European Union and there is no commercialization or operational restrictions in any of the countries. Hereby, advanced FEIG ELECTRONIC GmbH declares that this Bluetooth, Wi-Fi barcode scanner is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC...
- Page 24 14 Warranty Warranty FEIG ELECTRONIC warrants that the product will be free of defects in material and workmanship for 12 months from the date of shipment when used as intended. FEIG ELECTRONIC will, at its option, either repair or replace the defective products. Such repair or replacement shall be buyer’s sole remedy in the event of manufacturer’s breach of his limited warranty.