Related Manuals for Feig Electronic PAN MOBILE ID ECCO Lite
Summary of Contents for Feig Electronic PAN MOBILE ID ECCO Lite
- Page 1 IDENTIFICATION USER GUIDE ID ECCO:Lite Compact and Robust RFID-/Barcode Scanner H90313-0e-ID-B...
- Page 2 Composition of the information in this document has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
-
Page 3: Table Of Contents
IDENTIFICATION ID ECCO:Lite Contents Contents Safety Instructions Revision History of Documentation Scope of Delivery Product Description Technical Data Operation Charging the Battery ....................... 12 Device Reset ........................12 Configuration ........................12 6.3.1 Config.ini Configuration ..................12 Scanning .......................... 16 6.4.1 1D Laser ...................... -
Page 4: Safety Instructions
IDENTIFICATION ID ECCO:Lite 1 Safety Instructions 1 Safety Instructions Safety Instructions ► Please read this user guide carefully and follow the given instructions and safety instructions before using the device. ► The device may only be used for the intended purpose designed by the manufacturer. ►... - Page 5 IDENTIFICATION ID ECCO:Lite 1 Safety Instructions Do not place the device in the area over the air bag or in the air bag deployment area. Improperly ► installed wireless equipment could result in serious injury when the air bag inflates. Observe restrictions on the use of radio devices in fuel depots, chemical plants and areas where the air ►...
-
Page 6: Revision History Of Documentation
IDENTIFICATION ID ECCO:Lite 2 Revision History 2 Revision History of Documentation Revision History Revision Date Description 29.03.2019 Initial version Page 6 of 23... -
Page 7: Scope Of Delivery
IDENTIFICATION ID ECCO:Lite 3 Scope of Delivery 3 Scope of Delivery Scope of Delivery The scope of delivery includes following components: 1 x ID ECCO:Lite 1 x USB Charging Cable 1 x ID ECCO:Lite User Guide After unboxing please make sure, that all listed parts have been delivered properly and in good condition. Page 7 of 23... -
Page 8: Product Description
IDENTIFICATION ID ECCO:Lite 4 Product Description 4 Product Description Product Description The ID ECCO:Lite captures and stores barcodes data for a variety of uses and transmits those to a host via USB connection or Bluetooth. This document provides a basic instruction for using the ID ECCO:Lite device. Fig. - Page 9 IDENTIFICATION ID ECCO:Lite 4 Product Description Captured barcodes will be sent to the paired Bluetooth device according to the profile configured. Bluetooth not connected Cache mode activated Captured barcodes will be stored in the device memory. Cache mode deactivated Captured barcodes will be rejected. Batch mode Key 2 Press for 1 second to power on the device.
- Page 10 IDENTIFICATION ID ECCO:Lite 4 Product Description Bluetooth mode Bluetooth connected HiD SPP / iAP mode Blue LED (4) constantly on. Pressing key 4 shortly = no function Pressing key 4 for 4 seconds = send static data Bluetooth not connected Cache mode activated Pressing key 4 shortly = no function Pressing key 4 for 4 seconds = save static data...
-
Page 11: Technical Data
IDENTIFICATION ID ECCO:Lite 5 Technical Data 5 Technical Data Technical Data Mechanical Data Housing Double-walled Inside: robust ABS Outside: protective rubber coating Dimension (W x H x D) 87 mm x 48 mm x 26 mm (3.42“ x 1.89“ x 1.02“) Weight 96 g (3.39 oz) Protection Class... -
Page 12: Operation
IDENTIFICATION ID ECCO:Lite 6 Operation 6 Operation Operation 6.1 Charging the Battery Before the first operation, the main battery should be fully charged by using the included USB charging cable. As long as the battery is charging the red LED (3) will light solid red. After the battery is fully charged the red LED (3) turns off. - Page 13 IDENTIFICATION ID ECCO:Lite 6 Operation RightKeyText=”RIGHT” Set the static data you want to be saved or sent by Bluetooth if key 4 is pressed for 4 seconds. DeviceID=”0000” Set the custom device ID OutputFormatDB=”%t;%b” Set the record format for the data record (Batch mode). OutputFormatBT=”%b”...
- Page 14 IDENTIFICATION ID ECCO:Lite 6 Operation Cache=0 Cache=0 // do not save captured data when Bluetooth is not connected Cache=1 // save captured data in the device memory when Bluetooth is not connected Scomp=0 Scomp=0 // do not use SComP communication protocol Scomp=1 // use SComP communication protocol NOTE: SComP protocol must be supported by the application running on the paired device! Please refer to the SComP protocol description.
- Page 15 IDENTIFICATION ID ECCO:Lite 6 Operation EAN13_Verify=1 EAN13_XmitCheck=1 EAN13_SupplDgt=0 EAN13_ISBN_ISSN=0 EAN8_Enable=1 EAN8_Verify=1 EAN8_XmitCheck=1 EAN8_SupplDgt=0 EAN8_TruncExp=0 C39_Enable=1 C39_Verify=0 C39_XmitCheck=0 C39_MaxLen=99 C39_MinLen=1 C39_FullASCII=0 C39_XmitSS=0 I25_Enable=1 I25_Verify=0 I25_XmitCheck=0 I25_MaxLen=99 I25_MinLen=6 Codabar_Enable=0 Codabar_Verify=0 Codabar_XmitCheck=0 Codabar_MaxLen=55 Codabar_MinLen=5 Codabar_SSType=0 Codabar_XmitSS=1 C128_Enable=1 C128_Verify=1 C128_XmitCheck=0 C128_MaxLen=99 C128_MinLen=1 EAN128_Enable=1 EAN128_Verify=1 EAN128_XmitCheck=0 EAN128_MaxLen=99 EAN128_MinLen=1...
-
Page 16: Scanning
IDENTIFICATION ID ECCO:Lite 6 Operation 6.4 Scanning 6.4.1 1D Laser To scan a barcode follow the steps below: 1. Aim the scanner on the barcode. 2. Press the trigger key (5). 3. Ensure that the scanning line is directed straight on the barcode. 4. -
Page 17: Bluetooth Connection
IDENTIFICATION ID ECCO:Lite 7 Bluetooth Connection 7 Bluetooth Connection Bluetooth Connection To pair the Bluetooth enabled device to a Bluetooth enabled host. 1. Connect the device to the host using the USB port and use the Master Setup to set the data output mode to Bluetooth. -
Page 18: Transmitting Barcode Data To A Host
IDENTIFICATION ID ECCO:Lite 8 Transmitting Data to a Host 8 Transmitting Barcode Data to a Host Transmitting Data to a Host Batch mode All barcodes scanned in batch mode are saved in the file “Output.txt” on the removable drive “SCANNDY”. Connect the device to the host computer via USB and use the Windows-Explorer to navigate to the device “SCANNDY”. -
Page 19: Troubleshooting
IDENTIFICATION ID ECCO:Lite 9 Troubleshooting 9 Troubleshooting Troubleshooting Problem Possible Solution Device does not turn on. Make sure the battery is charged. • Press and hold the keys 1 to 4 for 5 seconds to reset the device. • Laser comes on but device does not •... -
Page 20: Maintenance And Cleaning
IDENTIFICATION ID ECCO:Lite 10 Maintenance and Cleaning 10 Maintenance and Cleaning Maintenance and Cleaning To clean the lense use a clean and dry cleaning cloth. Do not use chemical cleaners, lyes or similar. Page 20 of 23... -
Page 21: Disposal
IDENTIFICATION ID ECCO:Lite 11 Disposal 11 Disposal Disposal Never dispose of Li-Ion batteries in household waste! Li-Ion batteries can be disposed of at special collection points. Before disposal, make sure that the Li-Ion battery is completely discharged. Page 21 of 23... -
Page 22: Approvals
This equipment is intended to be commercialized in all the countries of the European Union and there is no commercialization or operational restrictions in any of the countries. Hereby, advanced FEIG ELECTRONIC GmbH declares that this Bluetooth, Wi-Fi barcode scanner is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC... -
Page 23: Warranty
13 Warranty Warranty FEIG ELECTRONIC warrants that the product will be free of defects in material and workmanship for 12 months from the date of shipment when used as intended. FEIG ELECTRONIC will, at its option, either repair or replace the defective products. Such repair or replacement shall be buyer’s sole remedy in the event of manufacturer’s breach of his limited warranty.