Advertisement
Quick Links
Advertisement
Related Manuals for Sub-Zero UC-24 Series
Summary of Contents for Sub-Zero UC-24 Series
- Page 1 subzero.com 800.222.7820 UC Series Service Manual Component Access & Removal...
- Page 2 Component Access/Removal Under Counter (UC-24) Series COMPONENT ACCESS AND REMOVAL This section explains how to adjust, access and/or remove Under Counter Series components. If different models have similar procedures, they are grouped together under the appropriate heading. The units covered in the proce- dures are listed between brackets after the heading.
- Page 3 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24B MODEL UC-24B EXTERIOR COSMETIC AND MECHANICAL COMPONENTS Kickplate (Model UC-24B) To remove the kickplate, extract the mounting screws Mounting Screw located at each end of the kickplate and pull the kick- (1 of 2) plate forward.
- Page 4 Component Access/Removal Under Counter (UC-24) Series Door Gasket (Model UC-24B) Channel An extruded dart at the back of the door gaskets is pressed into retaining channels that are part of the door glass frame. To remove the door gasket, pull the gasket from the retaining channels (See Figure 7-4).
- Page 5 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24B INTERIOR COSMETIC AND MECHANICAL COMPONENTS Wine Rack Assembly (Model UC-24B) To remove a wine rack assembly (See Figure 7-7): 1. Pull rack forward until it stops. 2. Lift front of rack up while continuing to pull forward. 3.
- Page 6 Component Access/Removal Under Counter (UC-24) Series Crisper Bin (Model UC-24B) To open or remove the crisper bin, grab the handle that is molded into the bottom front of the bin and pull bin forward (See Figure 7-10). Crisper Bin Glass Floor/Shelf Assembly (Model UC-24B) The glass floor/shelf assembly sets on top of the bin slides that are attached to each slide wall.
- Page 7 Component Access/Removal Under Counter (UC-24) Series Control Panel/Display Assembly (Model UC-24B) The control panel/display assembly is attached at the bottom front of the compartment by screws passing up from beneath the cabinet into screw grommets that are molded into the assembly. Control To remove the control panel/display assembly, first Panel...
- Page 8 Component Access/Removal Under Counter (UC-24) Series Evaporator Fan Shroud and Evaporator Cover (Model UC-24B) Screws pass though the refrigerator fan shroud and evaporator cover, then into screw grommet/stand-offs to secure the shroud and cover to the back wall. The evaporator cover is further secured by slots in its side h r o flanges fitting over pegs at the bottom of each shelf lad- der.
- Page 9 Component Access/Removal Under Counter (UC-24) Series Evaporator Fan Assembly (Model UC-24B) The evaporator fan assembly is attached to the rear wall with screws. To remove the evaporator fan assembly, first remove the cabinet slides and support spacers from the hinge- side wall, as well as the fan shroud and evaporator cover, then (See Figure 7-18):...
- Page 10 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24B UNIT TRAY MECHANICAL COMPONENTS Main Control Board Assembly (Model UC-24B) The control board assembly sits at the front left side of the unit tray, held in place with dual-lock fasteners, which is similar to velcro. To remove the main control board assembly, first remove the kickplate, then (See Figure 7-20):...
- Page 11 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24B SEALED SYSTEM COMPONENTS NOTE: To remove any sealed system component from an Under Counter appliance, the appliance must be pulled from its installation. When removing an Under Counter appliance from its installation, keep in mind that an anti-tip bracket and a countertop bracket may have been used to make a solid installation.
- Page 12 Component Access/Removal Under Counter (UC-24) Series Evaporator (Model UC-24B) The evaporator is attached to the rear wall with screws, behind the evaporator cover. NOTE: When removing the evaporator, the evaporator thermistor must be pulled from evaporator and reused in new evaporator. To Remove the evaporator (See Figures 7-25):...
- Page 13 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24C MODEL UC-24C EXTERIOR COSMETIC AND MECHANICAL COMPONENTS Kickplate (Model UC-24C) To remove the kickplate, extract the mounting screws Mounting Screw located at each end of the kickplate and pull the kick- (1 of 2) plate forward.
- Page 14 Component Access/Removal Under Counter (UC-24) Series Door Gasket (Model UC-24C) Channel An extruded dart at the back of the door gaskets is pressed into retaining channels that are molded into door liner. To remove the door gasket, pull the gasket from the retaining channels (See Figure 7-31).
- Page 15 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24C INTERIOR COSMETIC AND MECHANICAL COMPONENTS Wine Rack Assembly (Model UC-24C) To remove a wine rack assembly (See Figure 7-34): 1. Pull rack forward until it stops. 2. Lift front of rack up while continuing to pull forward. 3.
- Page 16 Component Access/Removal Under Counter (UC-24) Series Ice Bucket (Model UC-24C) To remove the ice bucket, grab the handle that is mold- ed into the bottom front of the bucket and pull bucket forward (See Figure 7-37). Ice Bucket Refrigerator Liner Cover (Model UC-24C) Screws pass though the refrigerator liner cover into the rear wall, securing the cover to the rear wall.
- Page 17 Component Access/Removal Under Counter (UC-24) Series Shelf Ladders (Model UC-24C) The shelf ladders are attached to the side walls with screws. To remove a shelf ladder, first remove the refrigerator liner cover. Then, extract the shelf ladder mounting screws and pull the shelf ladder away from side wall and out of compartment.
- Page 18 Component Access/Removal Under Counter (UC-24) Series Icemaker Assembly (Model UC-24C) The icemaker assembly is attached to the right side of Screws the evaporator cover with screws, two at the top of the icemaker and one at the bottom. To remove the icemaker assembly, (See Figure 7-43): 1.
- Page 19 Component Access/Removal Under Counter (UC-24) Series Defrost Terminator (Model UC-24C) The defrost terminator is attached to the evaporator out- Defrost Terminator let. To remove the defrost terminator, the mullion assembly must be removed first, then (See Figures 7-46): 1. Disconnect terminator wire leads from wire harness. 2.
- Page 20 Component Access/Removal Under Counter (UC-24) Series Evaporator Fan Assembly (Model UC-24C) Evaporator Fan Assembly Screws pass through the rear bracket of the evaporator fan assembly, as well as the baffle control assembly, into screw grommet/stand-offs to secure the fan assembly the back wall. To remove the evaporator fan assembly, first remove the mullion assembly, icemaker assembly, freezer air duct and evaporator cover, then...
- Page 21 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24C UNIT TRAY MECHANICAL COMPONENTS Main Control Board Assembly (Model UC-24C) The control board assembly sits at the front left side of the unit tray, held in place with dual-lock fasteners, which is similar to velcro. To remove the main control board assembly, first remove the kickplate, then (See Figure 7-52):...
- Page 22 Component Access/Removal Under Counter (UC-24) Series Water Valve (Model UC-24C) The quick-connect water valve is attached to a flange that is part of an air baffle that is attached to the unit tray. NOTE: To remove the water valve, the appliance must be pulled from its installation.
- Page 23 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24C SEALED SYSTEM COMPONENTS NOTE: To remove any sealed system component from an Under Counter appliance, the appliance must be pulled from its installation. When removing an Under Counter appliance from its installation, keep in mind that an anti-tip bracket and a countertop bracket may have been used to make a solid installation.
- Page 24 Component Access/Removal Under Counter (UC-24) Series Evaporator (Model UC-24C) The evaporator is attached to the rear wall with screws, behind the evaporator cover. To Remove the evaporator (See Figures 7-59): 1. Extract screws which hold evaporator to rear wall. 2. With a file, score a line around capillary tube, 1” (25 mm) or less from evaporator inlet, then fatigue cap- illary tube at this line until it separates.
- Page 25 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24R AND UC-24RO MODEL UC-24R AND UC-24RO EXTERIOR COSMETIC AND MECHANICAL COMPONENTS Kickplate (Models UC-24R, UC-24RO) To remove the kickplate, extract the mounting screws Mounting Screw located at each end of the kickplate and pull the kick- (1 of 2) plate forward.
- Page 26 Component Access/Removal Under Counter (UC-24) Series Stainless Steel Door Handle (Model UC-24RO ONLY) Handle Mount Screw A screw passing through the handle standoff into the Threaded Stud handle secures the handle to the standoff. The standoff then slides over a threaded stud that is attached to the door shell.
- Page 27 Component Access/Removal Under Counter (UC-24) Series Door Assembly (Models UC-24R, UC-24RO) Cabinet Hinge Mounting Screws NOTE: If removing a model UC-24R or UC-24RO from its installation, an anti-tip bracket and a countertop bracket may have been used to make a solid installa- tion.
- Page 28 Component Access/Removal Under Counter (UC-24) Series MODEL UC-24R AND UC-24RO INTERIOR COSMETIC AND MECHANICAL COMPONENTS Cantilever Shelf (Models UC-24R, UC-24RO) The cantilever shelf has hooks at the back of each side rail that hook into the slots of the shelf ladders that are attached at the back left and right corners of the cabi- net.
- Page 29 Component Access/Removal Under Counter (UC-24) Series Bin Slides (Models UC-24R, UC-24RO) The bin slides are attached to the side walls with screws. To remove a bin slide, first remove the glass floor/shelf assembly, then (See Figure 7-72). Screws 1. Extract slide mounting screws. 2.
- Page 30 Component Access/Removal Under Counter (UC-24) Series Evaporator Fan Shroud and Evaporator Cover (Models UC-24R, UC-24RO) Screws pass though the refrigerator fan shroud and evaporator cover, then into screw grommet/stand-offs to secure the shroud and cover to the back wall. The evaporator cover is further secured by slots in its side h r o flanges fitting over pegs at the bottom of each shelf lad-...
- Page 31 Component Access/Removal Under Counter (UC-24) Series Evaporator Fan Assembly (Models UC-24R, UC-24RO) The evaporator fan assembly is attached to the rear wall with screws. To remove the evaporator fan assembly, first remove the cabinet slides and support spacers from the hinge- side wall, as well as the fan shroud and evaporator cover, then (See Figure 7-77):...
- Page 32 Component Access/Removal Under Counter (UC-24) Series Model UC-24R AND UC-24RO UNIT TRAY MECHANICAL COMPONENTS Main Control Board Assembly (Models UC-24R, UC-24RO) The control board assembly sits at the front left side of the unit tray, held in place with dual-lock fasteners, which is similar to velcro.
- Page 33 Component Access/Removal Under Counter (UC-24) Series Model UC-24R AND UC-24RO SEALED SYSTEM COMPONENTS NOTE: To remove any sealed system component from an Under Counter appliance, the appliance must be pulled from its installation. When removing an Under Counter appliance from its installation, keep in mind that an anti-tip bracket and a countertop bracket may have been used to make a solid installation.
- Page 34 Component Access/Removal Under Counter (UC-24) Series Evaporator (Models UC-24R, UC-24RO) The evaporator is attached to the rear wall with screws, behind the evaporator cover. NOTE: When removing the evaporator, the evaporator thermistor must be pulled from evaporator and reused in new evaporator. To Remove the evaporator (See Figures 7-84): 1.