Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION Wiegand DS-2CD4A26FWD-IZS/P-WG
Summary of Contents for HIKVISION Wiegand DS-2CD4A26FWD-IZS/P-WG
- Page 1 Wiegand Camera Operation Manual...
-
Page 2: Table Of Contents
Wiegand Camera ·Operation Manual Table of Contents 1 About This Manual ..................1 2 Cameras ....................... 2 2.1 Available Models ........................2 2.2 Basic Parameters ........................2 2.3 Wiegand Interface Appearance ....................3 3 Solutions ...................... 4 3.1 Access Control Card No......................4 3.1.1 Overview ........................... -
Page 3: About This Manual
Wiegand Camera ·Operation Manual 1 About This Manual This manual is about the Wiegand configuration and features of network cameras. The manual is created as a guide for the technical support engineer, sales engineer, etc. -
Page 4: Cameras
Wiegand Camera ·Operation Manual 2 Cameras 2.1 Available Models The available models of network cameras are: DS-2CD4A26FWD-IZS/P-WG (2.8-12mm) DS-2CD4A26FWD-IZS/P-WG (8-32mm) DS-2CD4A26FWD-LZS/P-WG (2.8-12mm) 2.2 Basic Parameters Image sensor 1/1.8"Progressive Scan CMOS Max. resolution 1920 × 1080@ 60fps Illumination Ultra-low Iris Auto 120 dB Protection level IP 67... -
Page 5: Wiegand Interface Appearance
Wiegand Camera ·Operation Manual 2.3 Wiegand Interface Appearance Figure 2-1 Wiegand Interface Connection: Connect the block’s D0, D1 and GND to those of receiving terminal accordingly. -
Page 6: Solutions
Wiegand Camera ·Operation Manual 3 Solutions 3.1 Access Control Card No. 3.1.1 Overview Map the license plate number with the access control card number. Find the related card number in black and white list, then transfer the card information via Wiegand interface. 3.1.2 Advantage 1. -
Page 7: Configure Parameters
Wiegand Camera ·Operation Manual 8-digit number.） 16-digit number.） Here we take card number 12345 011 as example. The coding process are show as below. Split the card number as the card data (12345) and site data (011). Convert 12345 to binary format, as: 0011000000111001. ... -
Page 8: Enable Vehicle Detection
Wiegand Camera ·Operation Manual Figure 3-2 Wiegand Configuration Interface 3.2.2 Enable Vehicle Detection Steps: Go to Configuration->Road Traffic->Detection Configuration. Check the checkbox of Enable to enable Vehicle Detection. Set the specific detection parameters. Figure 3-3 Detection Configuration Interface 3.2.3 Configure Blacklist & Whitelist Steps: Go to Configuration->Road Traffic->Blacklist &... - Page 9 Wiegand Camera ·Operation Manual Figure 3-4 Blacklist & Whitelist Excel Template You can set at most 4096 license plates in whitelist and blacklist in total. You should enter 8-digit Card ID in the ID row. Otherwise, unknown error may occur. If you enter Card ID more than 8 digits, the last 8 digits will be kept.
- Page 10 Wiegand Camera ·Operation Manual The update frequency, update time, file name, etc. can be set. The corresponding URL protocol are listed as follows. http://10.5.148.102/ISAPI/System/Network/ftpUploadTimeUrl?enable=1&cycle=1&cust omDay=2&hour=0&name=test.xls Key Parameters Description: 10.5.148.102: replace it for the IP address of the device ...
- Page 11 Wiegand Camera ·Operation Manual Figure 3-6 Blacklist & Whitelist Interface Last Update shows the latest update time. Upload Info shows the rules to configure via FTP. Configure FTP Server. Steps: Go to Configuration -> Network -> Advanced Settings -> FTP Fill in the blanks based on the authority distributed by FTP Server.
-
Page 12: Transfer Plate Number Via Wiegand Interface
Wiegand Camera ·Operation Manual 3.3 Transfer Plate Number via Wiegand Interface 3.3.1 Overview Transfer the plate number via Wiegand interface, which is the private protocol. 3.3.2 Advantage Compatible directly with PAXTON access control system (managed by NET2 platform). 3.3.3 Applicable Wiegand Protocol 26-bit Wiegand Protocol 3.3.4 Plate Number Encoding Mode Plate Number... -
Page 13: Appendix
Wiegand Camera ·Operation Manual Figure 3-9 Settings Interface 4 Appendix 4.1 Paxton Configuration 4.1.1 Connect Net2 ACU Steps The connections for the ANPR Camera and Reader port using a Belden reader cable (as per Paxton specification) on the Net2 ACU are as follows: Blue wire: D1 at ANPR –... - Page 14 Wiegand Camera ·Operation Manual In the door settings for the ACU that will be connected to the ANPR camera, set the door up as follows and apply: In the user record, select the ‘Tokens’ tab and select ‘New Token’ to open the ‘Add new token’...
-
Page 15: View Anpr Captured Image In Net2
Net2 ACU. 4.1.2 View ANPR Captured Image in Net2 Hikvision has a second integration with Net2 that allows users to view DVR/NVR video from within the Net2 UI. This integration can be used in conjunction with the ANPR camera to show the capture of the licence plate as it is read by the camera. - Page 16 Wiegand Camera ·Operation Manual Add the DVR credentials to authenticate and detect the associated cameras: Click OK, then go to the ACU that is associated with the ANPR camera and select it as the camera that is monitoring the door.
-
Page 17: Ftp Server Creation
Wiegand Camera ·Operation Manual As the ANPR camera generates events in Net2, a camera icon will appear next to the event. Clicking the icon will show the video associated with the ANPR event. 4.2 FTP Server Creation Steps Use FTP server tool to create the FTP server in your PC. Set the permission information like user name and password in the server. - Page 18 Wiegand Camera ·Operation Manual...
- Page 19 Wiegand Camera ·Operation Manual...