Bowflex SelectTech 2080 Installation Manual

Bowflex SelectTech 2080 Installation Manual

Weight upgrade
Hide thumbs Also See for SelectTech 2080:

Advertisement

mportant Safety Instructions
I
This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Obey the following warnings:
Read and understand all warnings on the equipment.
• Carefully read and understand the Assembly and Owner's Manual.
• Keep bystanders and children away from the product you are assembling at all times.
• Do not try to change the design or functionality of this machine. This could compromise the safety of this machine and will void
the warranty.
Before each use, examine this machine for loose parts or signs of wear. Do not use if found in this condition. Contact Customer
Service (if inside US/Canada) or your local distributor (if outside US/Canada) for repair information.
• If replacement parts are necessary use only genuine Nautilus replacement parts and hardware. Failure to use genuine replace-
ment parts can cause a risk to users, keep the machine from operating correctly and void the warranty.
• Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's
Manual.
The Barbell/Curl Bar is very heavy. If you are not using the optional Barbell Stand, put the Barbell/Curl Bar assembly directly
on the floor for best support.
• Do all assembly steps in the sequence given. Incorrect assembly can lead to injury.
If you need assistance, contact Customer Service (if inside US/Canada) or your local distributor (if outside US/Canada).
To find your local international distributor, go to: www.nautilusinternational.com
Nautilus, Inc., 5415 Centerpoint Parkway, Groveport, OH 43125 USA, www.NautilusInc.com - Customer Service: North America (800) 605-3369, csnls@nautilus.
com | Nautilus (Shanghai) Fitness Equipments Co, Ltd, Room 1701 &1702, 1018 Changning Road, Changning District, Shanghai, China 200042, www.nautilus.
cn - 86 21 6115 9668 | outside U.S. www.nautilusinternational.com | Printed in China | © 2019 Nautilus, Inc. | Bowflex, the B logo and SelectTech are trademarks
owned by or licensed to Nautilus,Inc., which are registered or otherwise protected by common law in the United States and other countries. |
ORIGINAL DOCUMENT - ENGLISH VERSION ONLY
Refer to the Bowflex
instructions.
Parts
5-lb (2.27 kg) Weight Plates (qty 8)
Bowflex
SelectTech
2080 Barbell with Curl Bar Assembly/Owner's Manual for complete safety
SelectTech
Weight Upgrade
Installation Guide
Tools
6 mm
#2
Installation Guide
8022768.120119.A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SelectTech 2080 and is the answer not in the manual?

Questions and answers

Summary of Contents for Bowflex SelectTech 2080

  • Page 1 | Nautilus (Shanghai) Fitness Equipments Co, Ltd, Room 1701 &1702, 1018 Changning Road, Changning District, Shanghai, China 200042, www.nautilus. cn - 86 21 6115 9668 | outside U.S. www.nautilusinternational.com | Printed in China | © 2019 Nautilus, Inc. | Bowflex, the B logo and SelectTech are trademarks owned by or licensed to Nautilus,Inc., which are registered or otherwise protected by common law in the United States and other countries.
  • Page 2 Weight: 18.1 kg (40 lbs) Dimensions (Barbell set with Weight Upgrade plates): 158.6 cm L x 29.8 cm W x 32.2 cm H (62.4” x 11.7” x 12.7”) Assembly 1. Remove the Barbell and Weight Plates from the Base Note: Before removing the Barbell, set the adjustment knobs to the lowest weight selection (9.1 kg /20 lbs.). 2.
  • Page 3 3. Move Lock Pin Actuators NOTICE: Remove the Lock Pin Actuators and re-install in the inner set of screw holes in the Base End Shrouds to fit the 120-lb barbell configuration. Inner Lock pin Lock pin actuator actuator (X2) (X2) Outer 4.
  • Page 4 5. Adjust Base End Shrouds In order to avoid possible serious injury, when placing the Weight Plates in the Base Assembly, be careful to avoid fingers or hands being caught or pinched. Note: Push the shrouds inward. Tighten the inner screws. To tighten the outer screws, it may be necessary to remove the Barbell and Weight Plates.

Table of Contents