Related Manuals for Bowflex SelectTect BDS1642
Summary of Contents for Bowflex SelectTect BDS1642
-
Page 1: Assembly Instructions
2-In-1 Stand Assembly Instructions Model: BDS1642... - Page 2 Complete Stand Component Diagram � � �� �� � �� �� � � �� �� �� �� �� �� � �� �� �� � �� � �� �� �� � � �� �� ��...
-
Page 3: Tools Required
Parts Qty. Description TUBE, BOTTOM CROSS BRACE ASSEMBLY, REAR LEFT STABILIZER ASSEMBLY, REAR RIGHT STABILIZER ASSY, STAND LEG WELDMENT, LEFT DUMBBELL PLATFORM WELDMENT, RIGHT DUMBBELL PLATFORM WELDMENT, TOWEL BAR FOOT PEGS, SET OF FOUR HOLD DOWN STRAPS, 2F 2M NUT-NL 0.375-16 G2-BlkZ WASHER-FLAT 0.375 REGULAR BLKZ SCREW-BHCS 0.375-16x3.0 G2-BlkO SCREW-BHCS 0.375-16x2.75 G2-BlkO... - Page 4 step � Figure 1 Parts: • Stand Leg (#4) • Rear Left Stabilizer (#2) Hardware • 3" Screws (#12) • Washers (#11) • Nuts (#10) Tools: • Hex Key (7/32”) 1-1 Attach the Rear Left Stabilizer (#2) to the Stand Leg (#4) using the hardware shown in Figure 1. Note: Do not tighten hardware.
- Page 5 �� �� �� �� Figure 2 Parts: • Stand Leg (#4) • Rear Right Stabilizer (#3) Hardware • 3" Screws (#12) • Washers (#11) • Nuts (#10) Tools: • Hex Key (7/32”) 2-1 Attach the Rear Right Stabilizer (#3) to the Stand Leg (#4) using the hardware shown in Figure 2. Note: Do not tighten hardware.
- Page 6 step � �� Figure 3 Parts: • Cross Brace (#1) • Left Stand Leg assembly from Step 1 • Right Stand Leg assembly from Step 2 Hardware • 3" Screws (#12) • Washers (#11) • Nuts (#10) Tools: • Hex Key (7/32”) 3-1 Attach the Bottom Cross Brace (#1) to the Rear Left Stabilizer (#2) and Rear Right Stabilizer (#3) using the hardware shown in Figure 3.
- Page 7 �� �� �� �� �� Figure 4 Parts: • Stand Leg and Cross Brace assembly from Step 3 • Center Plate (#17) Hardware • 2.5" Screws (#14) • Washers (#11) • Nuts (#10) Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 4-1 Install the Center Plate (#17) to both Stand Legs (#4) using the hardware shown in Figure 4.
- Page 8 step �� �� Figure 5 Parts: • Stand base assembly from Step 4 • Left Dumbbell Platform (#5) Hardware • 2.75" Screws (#13) 2 • Washers (#11) • Nuts (#10) Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 5-1 Secure the Left Dumbbell Platform (#5) to left Stand Leg (#4) using the hardware shown in Figure 5.
- Page 9 � �� �� Figure 6 Parts: • Stand base assembly from Step 5 • Right Dumbbell Platform (#6) Hardware • 2.75" Screws (#13) 2 • Washers (#11) • Nuts (#10) Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 6-1 Secure the Right Dumbbell Platform (#6) to right Stand Leg (#4) using the hardware shown in Figure 6.
- Page 10 step � �� �� �� Figure 7 Parts: • Stand assembly from Step 6 • Towel Bar (#7) Hardware • 1" Screws (#15) • Washers (#11) • Nuts (#10) Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 7-1 Attach the Towel Bar (#7) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) using hardware shown in Figure 7.
- Page 11 �� Figure 8 Parts: • Stand assembly from Step 7 • Foot Pegs (#8) or Caster Wheels (#16) • Hold Down Straps (#9) 8-1 Attach either Foot Pegs (#8) or Caster Wheels (#15) to the Rear Left Stabilizer (#2), the Rear Right Stabilizer (#3), and both Stand Legs (#4).
- Page 12 16400 SE Nautilus Dr. Vancouver, Washington, USA 98683 1-800-NAUTILUS www.nautilus.com © 2006 Nautilus, Inc. All Rights Reserved. Bowflex and Bowflex SelectTech are either registered trademarks or trademarks of Nautilus, Inc. Specifications subject to change. P/N 000-3708 RevB 02/06...
Need help?
Do you have a question about the SelectTect BDS1642 and is the answer not in the manual?
Questions and answers