Do you have a question about the InnoSpire Elegance and is the answer not in the manual?
Questions and answers
Debbie
March 14, 2025
Not disbursing medication
2 comments:
Mr. Anderson
March 14, 2025
The PHILIPS Respironics InnoSpire Elegance may not be disbursing medication due to several possible reasons:
1. Nebulizer Tubing Issues – The tubing may be disconnected, blocked, or damaged. 2. Nebulizer Handset Problems – The handset may not be assembled correctly or could be clogged. 3. Air Filter Blockage – A dirty or clogged air filter can restrict airflow. 4. Compressor Malfunction – The device may not be producing sufficient compressed air. 5. Power Issues – The device may not be properly plugged in or switched on. 6. Cracks or Damage – If any part of the device is cracked or damaged, it may not function correctly.
Check these components and refer to the troubleshooting section of the manual if the issue persists.
This answer is automatically generated
Debbie
March 14, 2025
@Mr. Anderson
Debbie
March 14, 2025
No steam coming out of mouth piece
1 comments:
Mr. Anderson
March 14, 2025
There may be several reasons why no steam (aerosol) is coming out of the mouthpiece of the PHILIPS Respironics InnoSpire Elegance:
1. Nebulizer Tubing Issue – The tubing may not be properly connected to the compressor or nebulizer handset. 2. Blocked Nebulizer – The nebulizer handset may be clogged or not assembled correctly. 3. Air Filter Problem – A dirty or clogged air filter may be restricting airflow. 4. Compressor Malfunction – The compressor may not be generating sufficient air pressure. 5. Medication Issue – The medication may not be properly added or may not be suitable for nebulization. 6. Power Supply Problem – The device may not be turned on or may not be receiving power.
To resolve the issue, check the connections, clean or replace the necessary parts, and ensure the device is functioning properly. If the problem persists, contact Philips Respironics Customer Service.
This answer is automatically generated
Debbie
March 14, 2025
What does the filter look like?
1 comments:
Mr. Anderson
May 14, 2025
The appearance of the filter for the Philips InnoSpire Elegance is not described in the provided information. Therefore, its exact look cannot be determined.
This answer is automatically generated
Debbie
March 14, 2025
What does filter look like on Phillips innospire
1 comments:
Mr. Anderson
May 14, 2025
The filter for the Philips InnoSpire Elegance is small, lightweight, and comes with a large white cap for easy insertion and removal. It has a threaded construction for a tight seal and is designed to be compact for portability.
This answer is automatically generated
Debbie
March 14, 2025
What does filter look like?
1 comments:
Mr. Anderson
May 14, 2025
The filter for the Philips InnoSpire Elegance is white and fits under a white filter cap, which can be gently pulled out to replace the filter.
This answer is automatically generated
Subscribe to Our Youtube Channel
Related Manuals for PHILIPS Respironics InnoSpire Elegance
Summary of Contents for PHILIPS Respironics InnoSpire Elegance
Page 1
Compressor nebulizer system CAUTION: Federal (USA) law restricts this device to sale by or on the order of a physician or licensed healthcare professional. Système de nébuliseur à compresseur MISE EN GARDE : Aux États-Unis, la loi fédérale limite la vente de ce dispositif aux méde cins ou autres professionnels de la santé...
Page 2
PRECAUCIÓN: Las leyes federales (EE.UU.) limitan la venta de este dispositivo a un médico o profesional sanitario con licencia o bajo sus órdenes.
Important: Read these instructions carefully before using this device. If you have any questions or problems with the product, please contact your healthcare provider or Philips Respironics Customer Service at (inside the US) 1-800-962-1266, (outside the US) +33 1 47 52 30 00.
Page 4
Make sure that the electrical rating shown on the rating label on the bottom of the unit are available from Philips Respironics customer service at (inside the US) +1-800-345-6443 corresponds to your main voltage and frequency before plugging in the device.
Replacement of the nebulizer The nebulizer and other accessories should be replaced according to its instructions. authorized product distributor or Philips Respironics Customer Service at (inside the US) 1-800-962- Replacement of the filter 1266, (outside the US) +33 1 47 52 30 00.
ENGLISH Average flow rate 7 LPM @ 10 psig Max flow rate 9.4 LPM Weight 3.3 lbs Warranty Size 4.2 (H) x 6.5 (W) x 6.5 (L) inches Noise level 58 ±3dBA Class II device, Type B device (device with specific protection against electrical hazards). DOUBLE INSULATED Reference to standards Electric safety standards IEC 60601-1...
Page 7
ENGLISH Respironics New Jersey, Inc. warrants the compressor to be free from defects in materials and workmanship under normal use and operation for a period of 5 years from date of purchase from Respironics New Jersey, Inc. The warranty is limited to repair or replacement, at Respironics New Jersey, Inc.’s sole option, of any such component or equipment claimed to be defective when claim is shown to be bona fide by evaluation by Respironics New Jersey, Inc.
à ce produit, veuillez communiquer avec votre appareils à fréquence radio tels que les téléphones cellulaires, les téléavertisseurs, etc. fournisseur de soins de santé ou le service à la clientèle de Philips Respironics au 1-800-962- peuvent perturber le fonctionnement des équipements médicaux électriques. Par conséquent, 1266 (aux ÉtatsUnis) ou au +33 1 47 52 30 00 (à...
électriques. Communiquez avec veuillez communiquer avec votre distributeur agréé ou le service à la clientèle de Philips le service à la clientèle de Philips Respironics ou le distributeur de votre produit pour signaler tout produit endommagé.
FRANÇAIS Respironics au 1-800-962-1266 (aux États-Unis) ou au +33 1 47 52 30 00 (à l’extérieur des Appareil de classe II, appareil de type B (appareil avec protection spécifique contre les États-Unis). risques Garantie Respironics New Jersey, Inc. garantit un compresseur sans défaut de matériel ni de fabrication dans le Entretien et réparations cadre d'une utilisation et d'un fonctionnement normaux pour une période de 5 ans à...
Page 11
FRANÇAIS Marche (alimentation) Numéro de sérieClasse II, double isolation Arrêt (alimentation) Courant alternatifPièces de type B ATTENTIONNe pas utiliser à l’extérieur Consulter le mode d'emploiFabriqué par...
Este dispositivo cumple con el el servicio al cliente de Philips Respironics llamando al 1-800-962-1266 (dentro de EE.UU.) o al estándar CEI 60601-1-2 sobre compatibilidad electromagnética (CEM). Puede solicitar las hojas de +33 1 47 52 30 00 (fuera de EE.UU.).
Philips Respironics llamando al 1-800-962-1266 (dentro de EE.UU.) o al +33 1 47 52 30 00 (fuera de EE.UU.).
Page 14
OFF (apagado) Corriente alternaPiezas aplicadas Tipo B ATENCIÓNSolo para uso en interiores Siga las instrucciones Fabricado por para el uso Especificaciones técnicas Suministro eléctrico 120V/60Hz 1.7 Amp Protector de sobrecarga térmica Fusible térmico; temperatura de funcionamiento 150 °C Presión máxima del compresor 303 kPa (44 psi) Índice de flujo promedio 7 LPM a 10 psig...
Need help?
Do you have a question about the InnoSpire Elegance and is the answer not in the manual?
Questions and answers
Not disbursing medication
The PHILIPS Respironics InnoSpire Elegance may not be disbursing medication due to several possible reasons:
1. Nebulizer Tubing Issues – The tubing may be disconnected, blocked, or damaged.
2. Nebulizer Handset Problems – The handset may not be assembled correctly or could be clogged.
3. Air Filter Blockage – A dirty or clogged air filter can restrict airflow.
4. Compressor Malfunction – The device may not be producing sufficient compressed air.
5. Power Issues – The device may not be properly plugged in or switched on.
6. Cracks or Damage – If any part of the device is cracked or damaged, it may not function correctly.
Check these components and refer to the troubleshooting section of the manual if the issue persists.
This answer is automatically generated
@Mr. Anderson
No steam coming out of mouth piece
There may be several reasons why no steam (aerosol) is coming out of the mouthpiece of the PHILIPS Respironics InnoSpire Elegance:
1. Nebulizer Tubing Issue – The tubing may not be properly connected to the compressor or nebulizer handset.
2. Blocked Nebulizer – The nebulizer handset may be clogged or not assembled correctly.
3. Air Filter Problem – A dirty or clogged air filter may be restricting airflow.
4. Compressor Malfunction – The compressor may not be generating sufficient air pressure.
5. Medication Issue – The medication may not be properly added or may not be suitable for nebulization.
6. Power Supply Problem – The device may not be turned on or may not be receiving power.
To resolve the issue, check the connections, clean or replace the necessary parts, and ensure the device is functioning properly. If the problem persists, contact Philips Respironics Customer Service.
This answer is automatically generated
What does the filter look like?
The appearance of the filter for the Philips InnoSpire Elegance is not described in the provided information. Therefore, its exact look cannot be determined.
This answer is automatically generated
What does filter look like on Phillips innospire
The filter for the Philips InnoSpire Elegance is small, lightweight, and comes with a large white cap for easy insertion and removal. It has a threaded construction for a tight seal and is designed to be compact for portability.
This answer is automatically generated
What does filter look like?
The filter for the Philips InnoSpire Elegance is white and fits under a white filter cap, which can be gently pulled out to replace the filter.
This answer is automatically generated