Table of Contents
Advertisement
Quick Links
Owners &
Installation
LISTINGS AND CODE APPROVALS
These gas appliances have been tested in
accordance with AS/NZS 5263.0 & AS/NZS
5263.1.3 and have been certified by the
Australian Gas Association for installation and
operation as described in these Installation
and Operating Instructions. Must be installed
as per AS/NZS5601.
Your unit should be serviced annually by
an authorised service person.
DVi34L GAS INBUILT
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
WARNING:
Improper installation, adjustment, altera-
tion, service or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional in-
formation consult an authorised installer,
service agency or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other flam-
mable vapours and liquids in the vicinity of
this or any other appliance.
Installation and service must be performed
by an authorised installer, service agency or
the gas supplier.
920-236b
Models:
REFERENCE
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appli-
ance
Do not touch any electri-
cal switch: do not use any
phone in your building.
Immediately call your gas
supplier from a neighbour's
phone. Follow the gas sup-
plier's instructions.
If you cannot reach your
gas supplier, call the fire
department.
DVi34LNG
DVi34LLPG
DVi34LULPG
06/05/20
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Regency Fireplace Products DVi34L Series
Summary of Contents for Regency Fireplace Products DVi34L Series
- Page 1 Owners & Installation DVi34L GAS INBUILT Models: DVi34LNG DVi34LLPG DVi34LULPG PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WARNING: FOR YOUR SAFETY Improper installation, adjustment, altera- What to do if you smell gas: tion, service or maintenance can cause Do not try to light any appli- injury or property damage.
-
Page 2: Paring Your Remote Control
PAIRING YOUR REMOTE CONTROL REGENCY The control box will only learn the Remote ID codes during the first 30 seconds after power is applied and will ignore this special command from the Remote after the first 30 seconds. GAS INBUILT FIREPLACE To match the control box to the remote, follow the steps below : TO THE NEW OWNER Congratulations! You are the owner of a state-of-the-art Gas Inbuilt Fireplace by FPI. -
Page 3: Unit Dimensions-Flush Install
DIMENSIONS UNIT DIMENSIONS - FLUSH INSTALL FIREPLACE PRODUCTS INTERNATIONAL 3RD ANGLE TOLERANCES UNLESS PROJECTION OTHERW ISE STATED ±1° ANGULAR = PART : DVi34 GAS INSERT 7/4/2019 DIMENSIONS = ±0.031 MAT'L : BLANK SIZE : SEE ABOVE INSIDE BEND RADII = PROCESS : SHEAR/ PUNCH/ FORM DO NOT... -
Page 4: Unit Dimensions-With Spacer
DIMENSIONS UNIT DIMENSIONS - WITH SPACER FIREPLACE PRODUCTS INTERNATIONAL 3RD ANGLE TOLERANCES UNLESS PROJECTION OTHERWISE STATED ±1° ANGULAR = PART : DVi34 GAS INSERT 7/4/2019 DIMENSIONS = ±0.031 MAT'L : BLANK SIZE : SEE ABOVE INSIDE BEND RADII = PROCESS : SHEAR/ PUNCH/ FORM DO NOT UNITS IN INCHES... -
Page 5: Table Of Contents
TABLE OF CONTENTS OWNER'S INFORMATION OPERATING INSTRUCTIONS Paring Your Remote Control ..........2 Operating Instructions ..........22 Lighting Instructions ..........22 Shutdown Instructions ..........22 UNIT DIMENSIONS First Fire ..............22 Unit Dimensions-Flush Install ........3 Remote Control ............22 Unit Dimensions-With Spacer ........4 Summary of Controls ..........22 Fan Operation ............22 Adjusting Flame Height ..........22 DATA BADGE... -
Page 6: Data Badge
DATA BADGE This is a copy of the label that accompanies each Regency DVi34L Check the label on the unit and if there is a difference, the label on the Gas Inbuilt fireplace. We have printed a copy of the contents here for unit is the correct one. -
Page 7: Installation
INSTALLATION IMPORTANT MESSAGE BEFORE YOU START INSTALLATION CHECKLIST The Regency Gas Inbuilt must be installed in Installation is to be carried out ONLY by an accordance with these instructions. Carefully authorised person. Before installing vent system ensure that the read all the instructions in this manual first. damper plate is open and secure to prevent the 1) The appliance shall be installed in accord- damper plate from falling down and crushing... -
Page 8: Minimum Fireplace Opening
INSTALLATION MINIMUM FIREPLACE OPENING The minimum fireplace openings for the Regency DVi34L gas space heater are shown below: Lintel depth Height Width-Front Depth Width-Back Fascia flush Fascia With Lintel Depth (mm) Height (mm) Width Front (mm) Depth (mm) Width-Back (mm) Spacer Fascia flush (no spacer) Fascia with spacer... -
Page 9: Clearances To Combustibles
INSTALLATION CLEARANCES TO GAS CONNECTION Part # Description 948-640 76 mm Flex - 12.2 m COMBUSTIBLES 946-549 Co-linear DV Vertical GAS CONNECTION WARNING: Termination Cap Only persons licensed to work Minimum Clearances to Combustibles with gas piping may make the Co-linear DV From Unit necessary gas connections... -
Page 10: Flue Liner Installation
INSTALLATION The Air Intake pipe must be attached to the 4) Seal and or check the pilot outlet (# 8) inlet air collar of the termination cap. 5) The pressure check should be carried out with the unit burning and the setting should be within the limits specified on the safety label. -
Page 11: Installation In Masonry Or Zero Clearance Chimney
INSTALLATION INSTALLATION IN MASONRY OR ZERO CLEARANCE CHIMNEY 1) Measure and record dimensions to determine total Note: If you are planning to extend the height of the Flex Liner length requirements (see instructions below chimney using Direct Vent GS Pipe, please refer to the for details). -
Page 12: System Data
INSTALLATION System Data DVi34L DVi34LNG: For 0 to 610 meters altitude DVi34LLPG: For 0 to 610 meters altitude DVi34LULPG: For 0 to 610 meters altitude Burner Inlet Orifice Sizes: Propane ULPG Burner Max. Input 31.7 MJ/h Propane 30.6 MJ/h ULPG 26.4 MJ/h Min. -
Page 13: Conversion From Ng To Propane/Ulpg
DVi34 INSTALLATION Conversion Kit #337-968 for NG to Propane/ULPG Model THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Conversion Kit #337-968 from NG to Propane/ULPG Model 12) Replace the black "NATURAL GAS" onversion Kit Contains: Pull out the pilot hood by hand. -
Page 14: Log Set Installation
INSTALLATION DVi34 power cord. 18) Turn on gas supply and plug in After carrying out all adjustments, block the setting screws with paint, taking care not to obstruct the breather orifice of the pressure. 19) Adjusting the Outlet Pressure Put back the modulator plastic cap. All the adjustments must be carried out in the following order: WARNING: To ensure the correct operation of the modu-... - Page 15 GAS INSERT INSTALLATION U31-2 / IG34 LOG SET INSTALLATION LOG SET INSTALLATION Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot operation. The gas log kit (part # 402-935) contains the following: a) 02-43 Rear Log...
- Page 16 GAS INSERT INSTALLATION U31-2 / IG34 5) Place the Middle Left Log C)02-56 on the two pins as 7) Place the notch in Center Log E)02-47 over Log B)02- shown. 45 and across the cutout on Log A)02-43. E)02-47 A)02-43 C)02-56 B)02-45 Notch...
- Page 17 GAS INSERT INSTALLATION U31-2 / IG34 Front edge of 10) Place the embers and Rockwool on the exposed front rear burner burner tray. A)02-43 F)02-48 Side View Bracket The bottom right edge of Log F)02-48 must sit snugly against Separate platinum embers and place on and around the bracket and the front edge of the rear burner.
-
Page 18: Glass Door Installation
INSTALLATION GLASS DOOR INSTALLATION STANDARD FLUSH DOOR The standard flush door comes with a black frame. To install the frame and glass door, simply hook the top door flange onto the top of the unit and swing the door towards the unit, diagram 1. Be careful that the glass gasket does not roll up;... -
Page 19: Faceplate & Safety Screen Installation
INSTALLATION DVi34 IG34 INSTALLATION IG34 INSTALLATION FACEPLATE AND SAFETY SCREEN INSTALLATION (PART #337-914) FACEPLATE & SAFETY SCREEN INSTALLATION FACEPLATE AND SAFETY SCREEN INSTALLATION (***-***) FACEPLATE & OPTIONAL PLINTH TRIM ASSEMBLY IG34 INSTALLATION FACEPLATE & OPTIONAL PLINTH TRIM ASSEMBLY FACEPLATE AND SAFETY SCREEN INSTALLATION (***-***) DVi34L Faceplate Assembly IG34 INSTALLATION... -
Page 20: Optional Spacer Installation
INSTALLATION DVi34 IG34 INSTALLATION IG34 INSTALLATION OPTIONAL SPACER INSTALLATION (PART #337-918) IG34 INSTALLATION IG34 INSTALLATION OPTIONAL SPACER INSTALLATION PART #337-918 IG34 IG34 INSTALLATION INSTALLATION FACEPLATE & OPTIONAL PLINTH TRIM ASSEMBLY OPTIONAL SPACER INSTALLATION (***-***) FACEPLATE & OPTIONAL PLINTH TRIM ASSEMBLY OPTIONAL SPACER INSTALLATION (***-***) FACEPLATE &... -
Page 21: Final Check
INSTALLATION FINAL CHECK Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly. This includes: 1) Clocking the appliance to ensure the correct firing rate (rate noted on label) at 15 minutes. 2) If required, adjusting the primary air to ensure that the flame does not carbon. First allow the unit to burn for 15 min. to stabilize. 3) Check for proper draft. -
Page 22: Operating Instructions
OPERATING INSTRUCTIONS OPERATING FIRST FIRE SUMMARY OF INSTRUCTIONS CONTROLS The FIRST FIRE in your heater is part of the paint curing process. To ensure that the paint Before operating this appliance, proceed through On/Off Button is properly cured, it is recommended that you the following check list. -
Page 23: Copy Of Lighting Instruction Plate
OPERATING INSTRUCTIONS NORMAL OPERATING COPY OF LIGHTING INSTRUCTION PLATE SOUNDS OF GAS APPLIANCES It is possible that you will hear some sounds , AS/NZS 5601 from your gas appliance. This is perfectly normal due to the fact that there are various gauges and types of steel used within your appliance. -
Page 24: Maintenance
MAINTENANCE MAINTENANCE WARNING: CHILDREN AND LOG REPLACEMENT ADULTS SHOULD BE ALERTED INSTRUCTIONS TO THE HAZARDS OF HIGH The unit should never be used with broken logs. SURFACE TEMPERATURE AND Unplug the power cord and allow the unit to Any maintenance required accessing the cool before opening door to carefully remove SHOULD STAY AWAY TO AVOID glass door of the unit must be performed... -
Page 25: Fan Maintenance
MAINTENANCE FAN MAINTENANCE To Remove Fan: 1) Turn the unit off and allow it to cool to room temperature, 2) Unplug or disconnect power source to gas fire. 3) Open the bottom louvre. 4) Remove screws that secure protective screen. 5) Remove door frame and screen 6) Remove the ECS harness from the back clip. -
Page 26: Valve Assembly Replacement
MAINTENANCE VALVE ASSEMBLY REPLACEMENT 1) Unplug or disconnect the power source to the stove and shut off gas supply. 2) open bottom louvre and remove protective screen. 3) Remove the door frame and safety screen. 4) Remove the glass door, logs, and black or stainless inner liner, if installed. 5) Remove the rear log tray, burner and grate. -
Page 27: Inner Panel Removal And Installation
INNER PANEL REMOVAL AND INSTALLATION 1) Remove safety screen/guard. To install, do steps 6 to 1 in that order. 2) Remove the glass door by undoing 2 latches. Lift up and out. NOTE: When re-installing the back panel, ensure the bottop lip is Refer to pages 18 and 19 in the manual for detailed instructions. -
Page 28: Parts List
PARTS LIST ELECTRONIC COMPONENTS PARTS LIST Note: Depending on the model, the diagram below may not be exactly as shown - for reference purposes only. 910-936 910-082 910-089 910-088 910-912 910-084 911-101 910-526 910-080 911-183 910-083 910-514 910-521, 910-522, 910-523 911-121 FG38 FG39... -
Page 29: Main Assembly
PARTS LIST MAIN ASSEMBLY Part # Description Part # Description 337-574/P Valve Assembly - NG 911-101 Control Box ECS III 337-576/P Valve Assembly - LP 402-526 Grate/Diffuser Assembly 910-080 Gas Valve NG/LP 845 Sigma 1/2 in 425-017 Side Panel LH/RH (Each) NPT 0.845.088 336-061 Rear Panel Back... - Page 30 PARTS LIST MAIN ASSEMBLY Part # Description Part # Description 948-042 Bottom Black Hinge (Each) 910-909 Resistor Fan ECS SQHG-20W 904-603 Clamp Hose Stainless Steel 910-996 Wire Fan Resistor Jumper 948-223 Logo Plate Plastic Regency/Flame 911-047 Silicone Tubing 0.313 OD x 0.187 ID Silver 911-183 Switch Pushbutton Reset Blk SPST-...
-
Page 31: Faceplate Assembly
PARTS LIST FACEPLATE ASSEMBLY PART # 337-914 Faceplate Safety Screen IG34 INSTALLATION Mesh Bottom Screen 948-042 Hinge and Hnge Support Bottom Door *Not available as a replacement part TIONAL PLINTH TRIM ASSEMBLY AFETY SCREEN INSTALLATION (***-***) 5) Install the bottom door OTHER OPTIONAL ACCESSORIES 337-968 Conversion Kit LP/ULPG 337-918 Spacer... -
Page 32: Warranty
WARRANTY Limited Lifetime Warranty FPI Fireplace Products International Ltd. (“the manufacturer”) through its wholly owned subsidiary, Fireplace Products Australia Pty Ltd (for Australia and New Zealand customers) and sold under the Regency® brand of fireplace products (collectively referred to herein as “FPI”), extends this Limited Lifetime Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. - Page 33 WARRANTY part is returned to the distributor, dealer or agent for inspection if requested by FPI. Alternatively, FPI may at its own discretion fully discharge all of its obligations under the warranty by refunding the verified purchase price of the product to the original purchaser. The purchase price must be confirmed by an original copy of the tax invoice. The authorised selling dealer, or an alternative authorised FPI dealer if pre-approved by FPI, is responsible for all in-field diagnosis and service work related to all warranty claims.
- Page 34 WARRANTY FPI has no obligation to enhance or modify any unit once manufactured (i.e. as products evolve, field modifications or upgrades will not be performed on existing appliances). Any unit showing signs of neglect or misuse will not be covered under the terms of this warranty policy and may void this warranty.
- Page 35 WARRANTY Limitations of Liability: 1. Exclusion of implied terms The customer may have the benefit of consumer guarantees under the Australian Consumer Law. To the maximum extent permitted by law, all terms, conditions or warranties that would be implied into this Warranty or in connection with the supply of any goods or services by the supplier under law or statute or custom or international conventions are excluded.
- Page 36 WARRANTY How to Obtain Warranty Service: Customers should contact the authorised selling dealer to obtain warranty service. In the event the authorised selling dealer is unable to provide warranty service, please contact FPI by mail at the address listed below. Please include your name, address, purchase date, selling dealer, serial #, type of unit, a brief description of the problem, email and telephone contact information, and a copy of your original tax invoice.
- Page 37 WARRANTY Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.
- Page 38 Regency DVi34L Gas Inbuilt Fireplace...
- Page 39 Regency DVi34L Gas Inbuilt Fireplace...
- Page 40 IMPORTANT: A certificate of compliance or equivalent by an authorised installer must be obtained on commissioning of appliance to obtain warranty. Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ ©...
Need help?
Do you have a question about the DVi34L Series and is the answer not in the manual?
Questions and answers