Technical Data; Troubleshooting - Gardena TCS Li-18/20 Operator's Manual

s
4. Mount the new chain via the stop at the front
ensure the direction of movement of the chain and that the stop
at the front faces upwards.
5. Place the bar e on the motor unit
e
is inserted in the bar and the chain
sprocket g .
6. Replace the lid a (taking care of the rubber sealing gasket) and fasten
slightly with the two screws p
7. Tension the chain.
Tensioning the chain [ Fig. M5 / M6 ]:
RISK OF BURN INJURIES!
A too tightly tensioned chain can lead to motor overload and damage,
whereas insufficient tensioning can cause the chain to jump off the
rail. A correctly tensioned chain offers the best cutting performance,
optimum battery life and a longer service
life. Therefore, you should check the tensioning regularly as the chain
may expand when being used (especially when the chain is new; follow-
ing first installation, the tensioning of the chain must be checked after
the chainsaw has been used for a few minutes).
v However, do not tension the chain immediately after use but
wait until it has cooled down.
s e
1. Lift the chain off the bar
be approx. 2 – 3 mm.
2. Turn the adjustment screw j
chain is too low, or turn the adjustment screw
the tensioning of the chain is too strong.
a
3. Screw on the lid .
4. Start the device for approx. 10 sec.
5. Check the tensioning of the chain again and re-adjust, if necessary.
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the battery
charger always are clean and dry before you connect the battery charger.
Do not use running water.
v Clean the contacts and the plastic parts with a soft and dry cloth.
6. STORAGE
To put into storage [ Fig. O7 ]:
The product must be stored away from children.
1. Remove and charge battery (see 3. INITIAL OPERATION).
2. Clean Pole Pruner (see 5. MAINTENANCE), and slide protective
cover w onto the bar and close until the snap fit engages.
3. Store Pole Pruner in a dry and frost-free location.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
Disposal of the battery:
The GARDENA battery contains lithium-ion cells that should
not be disposed of with normal household waste at the end of
its life.
IMPORTANT!
v Dispose of the batteries through or via your municipal recycling
collection centre.
1. Discharge the lithium-ion cells completely (contact the GARDENA
Service).
2. Protect the contacts on the lithium-ion cells against short circuits.
3. Dispose of the lithium-ion cells properly.

7. TROUBLESHOOTING

DANGER! Risk of injury!
Cut injury when the Pole Pruner switches on unintentionally.
12
(A) e
of the bar
1 in such a way that the bolt
s
is placed around the drive
.
in the middle of the bar. The gap should
clockwise when the tensioning of the
j anticlockwise when
, and
v Before performing troubleshooting work, remove the battery
(see 3. INITIAL OPERATION), and slide the protective cover
onto the bar and close until the snap fit engages [ Fig. O7 ].
h
Problem
Pole Pruner does not
start up
Low runtime
Hedge is not cleanly cut
Pole Pruner cannot be
switched off
Pole Pruner stops.
¥
Error-LED flashes
(Lc)
Charging control lamp
on the charger does not
illuminate
(Lc)
Charging control lamp
the charger flashes red
Pole Pruner stops.
Error-LED ¥ flashes
The battery can no longer
be charged
Only an original GARDENA BLi-18 Replaceable Battery (Art. 9839) may be used.
This can be obtained from your GARDENA dealer or directly from GARDENA Service.
NOTE: For any other malfunctions please contact the GARDENA service depart-
ment. Repairs must only be done by GARDENA service departments or specialist
dealers approved by GARDENA.

8. TECHNICAL DATA

Battery Pole Pruner
Chain speed
Bar length
Chain type
Oil tank volume
Range of extension of
telescopic tube
Weight (including battery)
Sound pressure level L
1)
pA
Uncertainty k
pA
Li-ion
Sound power level L
1)
WA
Uncertainty k
WA
Hand/arm vibration a
2)
vhw
Uncertainty k
a
Measuring process complying with:
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
System Battery BLi-18
Battery voltage
Battery capacity
Battery charging time
80 % / 100 % (approx.)
Possible Cause Remedy
Battery is flat. v Charge battery
(see 3. INITIAL OPERATION).
Battery not pushed onto the v Push battery onto the handle
handle properly. and make sure that the
locking buttons snaps
in correctly.
Chain blocked. v Remove blockage.
Chain tensioned excessively. v Tension chain
(see 5. MAINTENANCE).
Chain not lubricated due to v Refill oil
lack of oil. (see 3. INITIAL OPERATION).
Chain dull or damaged. v Replace chain.
Start button is stuck. v Remove battery and loosen
start button.
Battery overload. v Wait for 10 sec.
Press button
battery and restart.
High temperature. The allowed v Leave battery to cool for
operation temperature was approx. 15 min. Press
exceded. button
restart.
Battery charger or charging v Connect the battery charger
cable are not connected and charging cable correctly.
correctly.
on Battery temperature is out of v Use the battery in surround-
range. ings where temperatures are
between 0 °C and 40 °C.
Battery error / v Press button
battery defective. battery and restart.
Battery is defective. v Replace the battery
(Art. 9839).
Unit Value (Art. 8866)
m/s 3.8
mm 200
px 90
cm 60
3
cm 0 – 50
kg 3.5
79
dB (A)
3
89
dB (A)
3
< 2.5
m/s
2
1.5
DIN EN ISO 22868 DIN EN ISO 22867
1) 2)
Unit Value (Art. 9839)
V (DC) 18
Ah 2.6
h 3.5 / 5
w
y
on the
y
on the battery and
y
on the