Related Manuals for NORDIC SEASON TORONTO 57
Summary of Contents for NORDIC SEASON TORONTO 57
- Page 1 TORONTO 57 – CO202000 USER MANUAL OUTDOOR USE ONLY! CAREFULLY READ THE SAFETY INSTRUCTIONS AND WARNING BEFORE USE ENGLISH...
-
Page 2: Safety Information
S A F E T Y I N F O R M A T I O N DANGER OF CARBON MONOXIDE POISONING WARNING! WARNING! FAILURE TO COMPLY WITH THE BURNING CHARCOAL INDOORS CAN BE INSTRUCTIONS AND WARNINGS IN THIS FATAL. CARBON MONOXIDE IS RELEASED MANUAL, CAN CAUSE FIRE, EXPLOSION, - AN ODOURLESS GAS. - Page 3 AMOUNT OF CHARCOAL/BRIQUETTES Recommended amount of charcoal: 1,5kg Maximum amount of charcoal: 1,8kg Recommended amount of briquettes: 1,8kg Maximum amount of briquettes: 2,2kg WARNING! Never overfill the grill with charcoal/briquettes, as it may damage the grill enamel if glowing charcoal falls from the charcoal grate and toward the grill body. Glowing charcoals may also fall out of the ventilation opening and cause fire or material damage when overfilled.
- Page 4 L I G H T I N G M E T H O D S We recommend using lighting briquettes, charcoal starter or electric grill starter for lighting charcoal/briquettes. Lighter fluid is not recommended. During lighting ● Grills with lids: Always have the lid off or open during lighting. Never close the lid before the flames from the charcoal have died down - to avoid damaging the lid surface.
-
Page 5: D U R I N G G R I L L I N G
D U R I N G G R I L L I N G ● Read page 3 for correct amount of charcoal/briquettes. ● Do not overfill the grill with charcoal/briquettes. The grill can get too hot for cooking and the heat can represent a risk to people or animals in the vicinity. ●... -
Page 6: Parts List
P A R T S L I S T PARTS LIST Image QTY. Image QTY. Tools needed for this assembly: Pliers or wrench Phillips screwdriver... - Page 7 P A R T S L I S T HARDWARE HARDWARE Qty. No. Image Part Description Qty. No. Image Part Description M6 x 15 Screw / washer / nut M6 x 15 Screw / washer / nut M6 x 30 Screw / washer M6 x 30 Screw / washer M8 Nut / washer M8 Nut / washer...
- Page 8 Step 3: Attach handle (1) to the fire bowl using screws , washers and nuts( A). STEP 3. . M6 x 15 2 PCS Align the charcoal grate support (6) hole and the leg base tube (9) to Step the fire bowl (8) holes, attach them using screws, washers and nut(A). Do not tighten.
- Page 9 Step 5: Insert the bottom shelf(16) into the long leg(15) ends. the bent tip goes into the Insert the bottom shelf(16) into the long leg(15) ends. the bent tip goes into the Step 5: hole of the long leg first, then align and insert the other end into the wheel legs(14). hole of the long leg first, then align and insert the other end into the wheel legs(14).
- Page 10 Step 7: Align the plastic parts( ) holes and the fire bowl holes, attach the plastic parts( ) to fire bowl using washers and nuts (E), then attach the small steel plate and big steel plate to the fire bowl using screw and washer(A). .
- Page 11 Step 9: Firstly place the charcoal grate into the fire bowl(8), then place the cooking grid(5) to the fire bowl. Finally all screws must be firmly tightened, Now your kettle is ready for use.
- Page 12 Always attach your receipt when making a warranty claim. Produced in China for Nordic Season Asia Co., Ltd. We are always looking for ways we can improve our products. We reserve the right to alter technical specifications at any time. You will always find the latest manual on www.nordicseason.no...