Table of Contents
Related Manuals for Baier BFF 222
Summary of Contents for Baier BFF 222
- Page 1 Original instructions Façade Cutter / Dresser 2 / 110 V Maschinenfabrik OTTO BAIER GmbH Heckenwiesen 26 D-71679 Asperg Tel. +49 (0) 7141 30 32-0 Fax +49 (0) 7141 30 32-43 info@baier-tools.com www.baie r-tools.com...
-
Page 2: Table Of Contents
Contents Contents ............................ 2 Important Information ......................2 Pictograms ..........................3 Explanation of the pictograms on the façade cutter ............... 3 Explanation of the pictograms used in the text ............... 3 For your Safety ......................... 4 General safety instructions for power tools ................4 1) Safety at the place of work .................... -
Page 3: Pictograms
Pictograms Explanation of the pictograms on the façade cutter The CE mark on a product means that the product conforms with all the applicable European regulations and has been subjected to the prescribed conformity assessment procedures. Protection class II equipment The machine is insulated in such a way that it has no exposed metal parts that could be live in the event of a fault. -
Page 4: For Your Safety
For your Safety General safety instructions for power tools WARNING Read all the safety instructions and precautions. Failure to observe the safety instructions and precautions can result in electric shock, fire and/or serious injuries. Keep all safety instructions and precautions for future reference. The term “power tool”... -
Page 5: Safety Of People
For your Safety 3) Safety of persons Always work carefully, attentively and sensibly when using a power tool. Do not use power tools if you are tired or are under the influence of drugs, alco- hol or medication. A moment of inattention while using the power tool can result in serious injuries. Wear personal protective equipment and always wear goggles. -
Page 6: Service
For your Safety Store power tools out of the reach of children when not in use. Do not allow people to use the tool unless they are familiar with it, or if they have not read this instruction manual. Power tools are dangerous if they are used by inexperienced people. Maintain power tools with care. -
Page 7: Electrical Safety
Asbestos-containing material may only be machined by specialists. − Wherever possible, use a dust extractor suitable for the material you are working on (e.g. a special BAIER dust extractor). − Ensure the workplace is properly ventilated. − We recommend wearing a face mask respirator with filter class P2 or P3 (to EN 149:2001). -
Page 8: Safety Of People
P2 or P3 (to EN 149:2001). The machine may only be used together with an approved dust extrac- tor (e.g. a special BAIER dust extractor). Anti-vibration safety gloves At a release value A (8) for arm-hand vibrations of over 2.5 m/s , the wearing of anti-vibration safety gloves is recommended. -
Page 9: Hazards When Using And Handling The Power Tool
For your Safety Never put down the power tool until the insert tool has come to a complete standstill. The rotating insert tool can come into contact with the surface on which the power tool is placed, which could cause you to lose control of the power tool. ... - Page 10 The machines can be very hot after use, do not touch the parts, risk of injuries. Additional signs or other, non BAIER-specific parts may not be screwed or riveted onto the motor, handle, gearbox or protective housing. This could damage the power tool and cause malfunctions.
-
Page 11: Service / Maintenance / Repair
Otherwise, all liability and warranty claims against Maschinenfabrik Otto BAIER GmbH expire. Ensure that original BAIER spare parts and original BAIER accessories only are used when needed. Original parts are available from authorised dealers. Use of non original parts can cause damage to the machine and an increased risk of accidents. -
Page 12: Technical Characteristics
Intended Use Provided it is tted with the relevant insert tool for the material to be machined, the BFF 222 façade cutter/dresser is suitable for the following uses: • for smoothing concrete surfaces, • for grinding and remedial work on oors (screed and industrial oors), •... -
Page 13: Machine Parts And Controls
Machine Parts and Controls 1 Connection cable 10 Allen key, SW 5 2 Handle 11 Star-type wheel dresser 3 Starting lockout button 12 Carbide grinding disc 4 ON / OFF switch 13 Star-type serrated wheel dresser 5 Cap 14 Carbide cutter with indexable inserts 6 Socket for 15 Diamond grinding disc dust extractor hose connection... -
Page 14: Insert Tools And Accessories
Insert Tools and Accessories BAIER insert tools for the BFF 222 façade cutter/dresser Area of use ID No. For remedial work on hard surfaces: 55327 Diamond grinding disc (Scope of supply: machining concrete surfaces (e.g. levelling 2 cutters, right/left-hand,... -
Page 15: Before Starting Work
(e.g. BAIER BSS 506 special dust ex- tractor) must be connected to the façade cutter. • Please note! We can only guarantee the machine's full performance if it is used with the BAIER BSS 506 dust extractor. • Danger! Risk of fire if cable drums used. -
Page 16: Adjusting The Front Handle
Before Starting Work (Figure 1) Adjust the front handle Figure 1 To enable comfortable handling of the machine, the tilt of the front handle (2) can be adjusted. • Use the Allen key SW 8 to undo the two hex socket cap screws (1). •... -
Page 17: Operation And Control
Operation and Control (Figures 2 and 3) Attach or replace insert tools Choose a cutter or grinding disc according to the intended use (see Table on page 14). Danger! Risk of fatal injuries due to electric shock. ► Disconnect the mains plug before carrying out any work on the façade cutter. Danger! Risk of injuries due to hot cutters or grinding discs. -
Page 18: Adjusting The Cutting Depth
Operation and Control (Figure 4) Adjust cutting depth Figure 4 • Caution! Damage to the carbide cutter, carbide cutter with indexable inserts or diamond grinding disc because cutting depth too large. ► For grinding work using the carbide cutter, carbine cutter with indexable inserts or diamond grinding discs, the guard plate (3) must be set to the smallest cutting depth, i.e. -
Page 19: Changing The Guard Plate
• Check the dust extractor is working properly and then push the dust extractor hose (3) firmly onto the socket (1). • The socket (1) is designed for the suction hose of BAIER's BSS 506 special dust extractor. • Please note! Greater effort may be required to push on the suction hose in cold ambient tempera- tures. -
Page 20: Switch On Façade Cutter And Cut
Operation and Control (Figure 7) Switch on façade cutter and cut Figure 7 • Caution! Damage to insert tools and gearbox. ► Prevent the machine from "dancing" on hard material and only use sharp insert tools, as otherwise the insert tools and gearbox can be damaged. •... -
Page 21: Cleaning
Only servicing and repair firms authorised by Maschinenfabrik OTTO BAIER GmbH may carry out maintenance of the machine. Also ensure that original BAIER spare parts and original BAIER accessories only are used. -
Page 22: Declaration Of Conformity
Declaration of Conformity BAIER BFF 222 façade cutter/dresser We herewith declare, with sole responsibility, that this product conforms with the follow- ing standards or normative documents: EN 60745 in accordance with the provisions of the Directives 2006/42/EC 7 July 2011... -
Page 23: Warranty
Servicing and cleaning work are not generally covered by the warranty. 4. Use of original BAIER spare parts Ensure that original BAIER spare parts and BAIER accessories only are used. They are available from authorised dealers. The type and quantity of grease are to be used according to the valid grease list. - Page 24 Maschinenfabrik OTTO BAIER GmbH Heckenwiesen 26, D-71679 Asperg Tel. +49 (0) 7141 30 32-0 Fax +49 (0) 7141 30 32-43 info@baier-tools.com www.baier-tools.com BAIER S.A.R.L. OTTO BAIER Italiana S.r.l. BAIER Scandinavia Aps 48, rue du Docteur Basset Via della Liberazione 21 Hammerbakken 12 –...