Nordson WM-1 Operator Card
Nordson WM-1 Operator Card

Nordson WM-1 Operator Card

Manual waterborne air spray gun
Hide thumbs Also See for WM-1:

Advertisement

Quick Links

Nordson Corporation
OPERATOR'S CARD
P/N 108 885B
Model WM-1 Manual Waterborne Air Spray Gun
Safety
The following symbols warn against dangers or
possible sources of danger. Become familiar with
them! Failure to heed a warning symbol could lead to
personal injury and/or damage to the unit or other
equipment.
Heed all warning symbols that appear in this
document, the operator's manual, or on the
equipment.
WARNING: Allow only qualified personnel to
perform the following tasks. Observe and
follow the safety instructions in this document
and all other related documentation.
WARNING: Risk of electrical shock. Spray
gun operation requires the use of a grounding
air hose and a high-dielectric strength fluid
tube. Failure to observe this warning may
result in personal injury, death, or equipment
damage.
WARNING: System or material pressurized.
Relieve pressure. Failure to observe may
result in serious burns.
Introduction
This operator's card contains only the information
necessary for installation, daily operation and
maintenance. For other information, refer to the
manual.
The WM-1 spray gun operates with an Iso-Flo HD
Issued 7/96
WARNING: Ignition hazard. Do not use this
handgun to spray coating materials having a
fire point below 60 _C (140 _F). Failure to
observe this warning may result in serious
injury and equipment damage.
CAUTION: Use only clean dry air. Failure to
observe this caution may reduce electrostatic
efficiency and cause equipment damage.
WARNING: Wear protective clothing, safety
goggles, and approved respiratory protection.
Failure to observe may result in serious injury.
CAUTION: Do not over tighten parts. Failure
to observe this caution may result in equipment
damage.
Always follow instructions in the material supplier's
Material Safety Data Sheet (MSDS) or material
information sheet.
Voltage Block unit (Iso-Flo). Each installation must
meet the following requirements:
The system, including the electrostatic power
supply, must be installed properly and in good
working condition.
1
21-37

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WM-1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Nordson WM-1

  • Page 1 For other information, refer to the The system, including the electrostatic power manual. supply, must be installed properly and in good The WM-1 spray gun operates with an Iso-Flo HD working condition. 21-37 Issued 7/96...
  • Page 2 Introduction (contd.) NOTE: Numbers in parenthesis throughout this The WM-1 spray gun air line must be attached to operator’s card correspond to the numbers on earth ground. Figure 1. 2137001B Fig. 1 WM-1 spray gun installation 1. Retaining ring 8. Rear slide 15.
  • Page 3: Daily Operation

    Iso-Flo HD unit fluid and air pressure. 2. Slide the trigger lock (14) all the way down. 6. Cover the exterior of the WM-1 spray gun with a Nordson spray gun cover. 3. Perform the tasks necessary to set fluid pressure in the fluid delivery system.
  • Page 4: Maintenance

    Maintenance 2137003A 2137008A 1. Relieve the air and fluid pressure. Turn the 2. Trigger the WM-1 spray gun into a grounded electrostatic unit off. metal container to drain the fluid tube. 2137004A 2137005A 3. Point the WM-1 spray gun downward and 4.
  • Page 5 2137012A 2137013A 10. Trigger the WM-1 spray gun. Insert the 11. Hang up the WM-1 spray gun. fluid tip into the gun. Place the air cap on the fluid tip. Install the retaining ring and tighten securely.
  • Page 6: Connections And Controls

    Connections and Controls Table 1 describes each input and control of the WM-1 spray gun. Numbers in the Connections and Controls column correspond to the numbers on Figure Table 1 Connections and Controls Connections and Controls Functions Thumb wheel (pattern/horn)
  • Page 7: Specifications

    (contd.) Weight Hose Connections (contd.) Perform these steps if you ordered the WM-1 spray 400 grams (14 oz) gun without hoses, part 176 501: NOTE: Weight includes fluid tip, air cap, and retaining 1. Loosen the captive screw (6) securing the rear ring.
  • Page 8: Troubleshooting

    Poor coverage in Raise atomizing air and coating material pressure; reduce electrostatic power supply recesses voltage; move closer to substrate. 1996 Nordson Corporation Nordson, the Nordson logo and Iso-Flo are registered trademarks of Nordson Corporation. 21-37 Issued 7/96...

Table of Contents