Advertisement
Quick Links
Advertisement
Related Manuals for RAISE 3D BondTech N1
Summary of Contents for RAISE 3D BondTech N1
- Page 1 R/\ISE3D BondTech Single/Dual Extruder Installation Guide...
- Page 2 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) • Hardware Installation STEP 1: Unloading Unload the filament from both nozzles. After the filament has been removed, power off the printer. STEP 2: Unplugging Cables.
- Page 3 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) STEP 3: Remove the Original Extruder 3.1 Remove the 2 screws on the left and right side with 2.5 mm hex wrench. 3.2 Remove the 2 screws on the back side with 2.5mm hex wrench. WWW.RAISE3D.COM AMERICA ·...
- Page 4 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) 3.3 Remove the 2 screws fixing the cable chain with a 2.5mm hex wrench. 3.4 Remove the 2 screws fixing the extruder board and its origin cover with a 2.5mm hex wrench. 3.5 Remove the original extruder by pulling it straight up.
- Page 5 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) STEP 4: Install the New Extruder 4.1 Insert the two PTFE tubes into the mounting holes under the new dual-extruder and push the extruder all the way down. 4.2 Install the original screws to the left and right (2,5mm hex wrench). Do not tighten the screws fully. WWW.RAISE3D.COM AMERICA ·...
- Page 6 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) 4.3 Install the 2 rear old screws with a 2.5mm hex wrench. Do not tighten the screws fully. (both sides and the rear screws) • Re-tighten the screws in turns, Do this carefully to prevent any material cracks. DO NOT OVERTIGHTEN.
- Page 7 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) 5.2 Attach the board holder. Note that the bottom screw is M2.5 and the upper one is M3. 5.3 Fix the cable chain with the original screws. WWW.RAISE3D.COM AMERICA · ASIA · EUROPE...
- Page 8 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) STEP 6: Wiring (divided in Dual-extruder and Single- extruder) 6.1 Remove the unmarked cable. To reverse the two cables, you can use a sharp tool to lift the little plastic tab on the connector and gently pull the crimping contact out of the housing with your hand.
- Page 9 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) 6.3 Plug the unmarked cable onto the rear motor and the marked cable into the front motor. WWW.RAISE3D.COM AMERICA · ASIA · EUROPE...
- Page 10 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) 6.4 Use the zip tie to secure them, then cut tail of the zip tie. 6.5 Do the same operation at the bottom and cut of the ends. WWW.RAISE3D.COM AMERICA · ASIA · EUROPE...
-
Page 11: Software Configuration
Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) • Software Configuration The E-step value tells the controller how many steps (micro steps) that needs to be sent to feed 1mm of filament. The Raise3D E-step value needs to be updated to achieve the correct extrusion volume for the new extruder. - Page 12 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) Go to More Settings -> Hardware -> Step Per Unit. to edit E Steps Per Unit. Set the E Steps Per Unit to be 415. WWW.RAISE3D.COM AMERICA · ASIA · EUROPE...
- Page 13 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) Double check that the new value has been changed to be 415. • Electronic Configuration The stepper driver needs to be adjusted because we have changed the previous motor(s) to smaller one(s) that requires a lower current.
- Page 14 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) Touch the black probe to the potentiometer on the stepper driver in the top to the left. Touch the red probe to the lower screw of the green terminal. Now you can see the Vref voltage of the driver. WWW.RAISE3D.COM AMERICA ·...
- Page 15 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) • Turn the adjusting screw carefully until you reach the value of about 0,8V(800mV), clockwise increase, counter-clockwise decrease. • Carry out the operation to all the top three drivers. Touch the black probe to the potentiometer on the stepper driver in the top to the left. Touch the red probe to the lower screw of the black terminal.
- Page 16 Installation Guide of BondTech Single/Dual Extruder (N-Series Printer Only) • Turn the adjusting screw carefully until you reach the value of about 0,9V(900mV), clockwise increase, counter-clockwise decrease. • Carry out the operation to all the bottom three drivers. WWW.RAISE3D.COM AMERICA · ASIA · EUROPE...