Specifications Table Page 28 Troubleshooting Page 32 Quick reference tables for Manual Button Control and Remote Controller guide for PIN Set and Manual Button Disable/ Enable www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 2
It is available in Standard and Premium variants For Standard and Premium Variants : The illuminator has a photocell for automatic day/night switching and also benefits from Raytec’s interchangeable lens system so that the correct angle of illumination can always be achieved easily. www.rayteccctv.com...
Page 3
External Input, volt free or TTL – orange (TTL +ve) & purple (TTL GND) for illustrative External Output, volt free – yellow & white CAT 5 Cable purposes for PoE www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
STEP 1: Safety Information (Pg. 2) STEP 2: Physical Installation (Pg. 5) Adjust interchangeable lens if required. Fix to wall, pole or camera unit using U bracket provided or other Raytec bracketry. IMPORTANT: Ensure illuminator is rated to provide required viewing distances and select...
Page 5
VARIO2 PoE is delivered as standard with bracket at the bottom of the unit. This can be moved to top of the unit if required. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 6
Ensure you make a waterproof connection to the RJ45 as shown below. Ensure the connector is waterproof and sealed after the connection is made. To illuminator RJ45-RJ45 connector To PSE www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 7
External Input -Volt free or TTL +ve Purple External Input -Volt free or TTL GND Yellow External Output – Volt free White External Output - Volt free www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 9
Step 6 : Security (Optional PIN protection) Set PIN (If Required) (Can only be done with the optional VARIO Remote Controller (VRC) – See Detailed Section www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Operating Mode. However, if you use the manual push buttons at all during this time, the illuminator will automatically enter operating mode 30 minutes after the last button press. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 11
Mode is LED Status Indicators Enable/Disable, entering a PIN or disabling manual push buttons (if done at the same time as disabling the remote – see P. 22) www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Note : Reset button will not remove a PIN if one is present Note : Unless detailed as part of the functionality, if an invalid or blocked command is attempted, both LEDs will flash RED www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 13
PIN function. Note : Unless detailed as part of the functionality, if an invalid or blocked command is attempted, both LEDs will flash RED www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
FLASHING GREEN shows that a PIN has been previously set. As you input the four correct characters the number of flashes will reduce and you will be returned to programming mode. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 15
*Note – If you are trying to access a PIN in Operating Mode, hold the status button down for 4 seconds and both LEDs flash RED, this means there is no PIN present. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
The buttons are active in both programming mode and operating mode regardless of whether a PIN is present, unless you have previously disabled the manual buttons. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 17
LEDs will flash Red *Note: – If the status indicator LEDs are disabled and you use the manual buttons the indicator LEDs will still illuminate accordingly www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 18
The settings programmed by the manual push buttons will be retained upon power recycling unless a reset has been performed, in which case the factory defaults will be applied. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 19
RHS LED 1 Flash GREEN Medium Sensitivity: RHS LED 2 Flashes GREEN High Sensitivity: RHS LED 3 Flashes GREEN Disabled photocell: RHS LED Solid RED www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 20
LEDs will go blank for 1 second and then return to the standard indication of either operating mode or programming mode (depending on which mode the illuminator was in previously before selecting manual controls) www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 21
30 minutes after the last button press (e.g. if you press any manual button at 29 minutes – your 30 minute window will start over). www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Note : This command can only be used within 5 minutes of the illuminator being put into Operating Mode.(If the Manual Buttons are already Disabled, both LEDs will flash RED straight away) www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 23
This is a FULL RESET and will restore factory settings AND remove the PIN if one has been set. Both Indicator LEDs will flash AMBER when completed. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 24
If a PIN is present - You need to enter your PIN - Or do a full Re-set www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Standard Bracketry : Supplied with the Product (Model Dependant) (Not to scale, dimensions rounded to nearest mm) www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 26
75 x 100 x 64mm Dimensions (5”x7”x3”) 4”x5”x2.5”) 3”x4”x2.5”) Cat 5 Cable 2.5m 2.5m 2.5m 2.5m 2.5m 2.5m 2.5m Length For Covert IR940nm Distances please contact Raytec www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 27
2.5m 2.5m 2.5m 2.5m 2.5m Cable Length For Covert IR940nm Distances please contact Raytec Standards: CE (Covering EMC, Safety, IP rating) IEC/EN 62471 (Photobiological Safety) www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 28
• If Premium variant - Ensure telemetry wires are shorted out or valid telemetry input (zero volt or TTL) is applied and correctly wired www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 29
In extreme sunlight conditions, distance between remote and unit may need to be reduced Programming may be disabled. Enter PIN to retrieve control or RESET illuminator using one of the two RESET modes. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 30
Too wide and there may be insufficient light on scene and light going where it is not needed. Check Camera model number to Raytec performance specification to ensure required distance is achievable www.rayteccctv.com...
Page 31
Camera make and model • Camera Lens make and model If the Raytec illuminator or remote control is still not delivering the required performance, please contact us for further assistance: UK / Europe Tel: +44 (0) 1670 520055 Americas Tel: +1 613 270 9990...
Page 32
Remote and you are in Enter Operating Programming Mode you Mode cannot change to Programming Mode – unless you enter your PIN first www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 33
If no buttons are pressed within 2 minutes then the illuminator will automatically default back into the previous mode it was in – programming or operating mode. www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 34
Amber LED Control> - Off go Solid for 4 Amber when seconds the disable remote button is pressed and turn off when in Operating Mode www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 35
Red counts Mode after for 4 Flashing down the PIN deleted. seconds Red / No. of valid Green - characters Green required – Flashing Amber www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...
Page 36
VA2 POE/16/1.0 www.rayteccctv.com Raytec Global Tel : +44(0) 1670 520055 Americas Tel : +1 613 270 9990...