Keysight Technologies N9000B Installation Note page 17

Final Installation for Standard Instruments (Benchtop Configuration,
1. Refer to Figure 1. Locate the new instrument dress cover (N9020-00068) in the kit. Carefully
slide the instrument cover onto the instrument from the rear of the analyzer, making sure not
to damage any internal cables. The seam on the cover should be on the bottom of the
instrument. Be sure the cover seats into the gasket groove in the Front Frame Assembly.
2. Locate the four new rear feet (5041-7903), the four 25mm long M5 pan head screws
(0515-1619) and the four flat washers (3050-0893) in the kit. Install the four rear feet (4) to
the rear of the instrument using the four screws (3) and washers. Torque to 21 inch pounds.
3. Locate the two new strap handles (N9020-60252) in the kit. Install the strap handles (2) on
both sides of the instrument using the four screws (1). Torque to 21 inch pounds.
4. Locate the Top Trim Strip, without bumpers (N9020-40005) in the kit. Attach the Top Trim
Strip to the top of the Front Frame Assembly.
5. Locate the two Side Trim Strips (5041-7905) in the kit. Remove the backing and apply one
Side Trim Strip to each side of the Front Frame Assembly.
6. Locate the four new Bottom Feet (5041-7906) and two Tilt Stands (1460-1345) in the kit.
Attach two of the Tilt Stands to two of the Bottom Feet. Install the two bottom feet with the
tilt stands to the bottom of the analyzer near the front of the analyzer. Install the other two
bottom feet to the bottom of the analyzer near the rear of the analyzer.
7. Locate the four new Key Locks (5021-2840) in the kit. Install the four key locks to the bottom
feet.
Final Installation for Portable Instruments (Option PRC,
1. Refer to Figure 3. Locate the new instrument dress cover (N9020-00068) in the kit. Carefully
slide the instrument cover back onto the instrument from the rear of the analyzer, making sure
not to damage any internal cables. The seam on the cover should be on the bottom of the
instrument. Be sure the cover seats into the gasket groove in the Front Frame Assembly.
2. Refer to Figure 3. Locate the four new Rear Bumpers (N9020-40015), the four 25 mm long M5
pan head screws (0515-1619) and the four flat washers (3050-0893) in the kit. Install the four
rear bumpers (2) to the rear of the instrument using the four screws (1) and washers. Torque
to 21 inch pounds.
3. Refer to Figure 2. Locate the four new Hole Plugs (N9020-40015) and four 14mm long M5 flat
head screws (0515-5209) in the kit. Replace the four hole plugs (5) to both sides of the
instrument.
4. Locate the Top Trim Strip, Opt PRC (N9020-40006) in the kit. Attach the Top Trim Strip to the
top of the Front Frame Assembly.
5. Locate eight of the 14 mm long M4 pan head screws (0515-0435) and four new front bumpers
(N9020-40016) in the kit. Secure the front bumpers (4) to the front frame assembly using the
screws (1) Torque to 21 inch pounds.
6. Refer to Figure 2. Locate the remaining four 14mm long M4 pan head screws (0515-0435) and
the new Bail Handle Assembly (N9020-60251) in the kit. Install the bail handle (2) (using the
four screws (1)) to the Front Frame Assembly. Torque to 21 inch pounds.
7. Locate the four Bottom Foot Hole Plugs (N9020-40007) in the kit. Install the Bottom Foot Hole
Plugs in spaces provided on the bottom of the dress cover.
Installation Note N9000-90039
Option T03 and T06, Tracking Generator Upgrade Kit
and
Figure 2
)
Figure 1
)
Figure 3
17