Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Telephone
  5. Hybrid IP-PBX
  6. Getting started

Panasonic Hybrid IP-PBX Getting Started

Hide thumbs Also See for Hybrid IP-PBX:

Advertisement

Quick Links

Download this manual
Thank you for purchasing the Panasonic Hybrid IP-PBX, KX-TDA15.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDA15: Version 1.1
Model No.

Table of Contents

........................................ 4
Hybrid IP-PBX
Getting Started
KX-TDA15
........................... 2
............. 12
............ 21
..... 15

Advertisement

loading

Related Manuals for Panasonic Hybrid IP-PBX

Summary of Contents for Panasonic Hybrid IP-PBX

  • Page 1: Table Of Contents

    4 Customising the Hybrid IP-PBX ..15 5 Confirming the Connection .... 21 Thank you for purchasing the Panasonic Hybrid IP-PBX, KX-TDA15. Please read this manual carefully before using this product and save this manual for future use. KX-TDA15: Version 1.1...

  • Page 2: Before Installation

    DSS Console Detail Recording (SMDR) 4 Super Hybrid Ports Wireless Phone PT-interface CS PS Server PC Main Board KX-T7600 DPT KX-T7600 DPT The Hybrid IP-PBX has 4 Super Hybrid Ports, one BRI2 card, and one EXT-CID card pre-installed. Getting Started...
  • Page 3 Unpacking Check the package contents. × Main Unit × CD-ROM (including manuals, etc.) × × × AC Cord* AC Adaptor Screw × × Mini Plug (for pager and Washer SD Memory Card × music source) × × Main Strap Optional Card Label Sheet * The type of the AC cord may vary depending on the country/area of use.

  • Page 4: Installation

    Installation Opening/Closing the Covers Opening the Covers Pull the slide button to the right and, holding it, slide the cable cover upwards. Then turn the cable cover slightly to remove it. Slide Button Cable Cover Remove the three screws. Screw Holding the protrusions on both sides of the front cover, swing the cover open.
  • Page 5 Closing the Covers Close the front cover, then tighten the three screws. Screw Attach the rear hooks on the cable cover to the main unit, then swing the cable cover closed so that the front hooks fit in place. Cable Cover Slide the cable cover down until it locks.
  • Page 6 Installing the SD Memory Card The SD Memory Card contains software for all the processes of the Hybrid IP-PBX and all the customer data. The SD Memory Card must be inserted before start up. SD Memory Card SD Memory Slot Cover...
  • Page 7 Slot Restrictions The following table shows the slot restrictions. " " indicates that the slot supports the optional service card. Card Slot Number Type LCOT2 BRI2 BRI1 IP-GW4 DLC8 SLC8 DPH4 DPH2 ECHO8 MSG2 Only one of either DLC8 or SLC8 card can be installed. Only one of either DPH4 or DPH2 card can be installed.
  • Page 8 Optional Service Card Extension Bolt CAUTION When installing the optional service cards, do not put pressure on any parts of the main board. Doing so may result in damage to the Hybrid IP-PBX. Getting Started...
  • Page 9 Insert the new extension bolt (included with the card) into the hole on the card, and tighten it to secure the card. Extension Bolt Installing the Trunk Cards LCOT2 Card RJ45 To trunk Accessory (included): Extension Bolt × 1, Strap × 1, Optional Card Label × 1 User-supplied (not included): RJ45 connector Getting Started...
  • Page 10 BRI1/BRI2 Card Example: BRI2 Card RJ45 (LINE 1) RJ45 (LINE 2) To NT1 Accessory (included): Extension Bolt × 1, Strap × 1, Optional Card Label × 1 (for BRI1 card) User-supplied (not included): RJ45 connector Notes • Connect these optional service cards to the trunk through an NT1; do not connect to the U interface of the trunk directly.
  • Page 11 The earth wire of the AC cable has an effect against the external noise and lightning strikes, but it may not be enough to protect the Hybrid IP-PBX. A permanent connection between earth and the earth terminal of the Hybrid IP-PBX must be made.

  • Page 12: Starting The Hybrid Ip-Pbx

    • Once you have started the Hybrid IP-PBX and if you unplug the Hybrid IP-PBX, do not perform the following procedures to start the Hybrid IP-PBX again. Otherwise, your programmed data will be cleared.
  • Page 13 Plug the DC connector of the AC adaptor into DC IN 1. DC IN 1 DC Connector AC Adaptor Plug the AC cord into the AC adaptor, and then plug the other end into an AC outlet. AC Adaptor AC Cord To AC outlet Turn on the power switch.
  • Page 14 3 min. If successfully executed, the RUN indicator will stop flashing and be kept lit. All data will be cleared and the Hybrid IP-PBX will be initialised to the default values. The DPTs should show the time as 01:00.

  • Page 15: Customising The Hybrid Ip-Pbx

    KX-TDA15 is shared by both the KX-TDA15 and KX-TDA30, and is referred to as the “KX-TDA30 Maintenance Console”. KX-TDA30 Maintenance Console’s Quick Setup lets you easily configure the Hybrid IP-PBX to receive intercom and trunk calls, as well as apply basic settings such as time and date.
  • Page 16 Quick Setup will launch automatically. During Quick Setup, you will setup the following basic items: • Date and Time of the Hybrid IP-PBX. The date and time set on the PC will be used. • System Password for installer for PC programming.
  • Page 17 Connect the PC to the Hybrid IP-PBX with a USB cable. Start the KX-TDA30 Maintenance Console from the start menu. a. Type the Installer Level Programmer Code (default: 1234). b. Click [OK]. Click "Connect" "USB" or "RS-232C" from the menu bar, depending on the serial interface connection with the Hybrid IP-PBX.
  • Page 18 The programme menu appears. Assigning the BRI Setting (Automatic Configuration) a. Double-click "Configuration". b. Double-click "Slot". c. Change the status of the BRI card to OUS. d. Click [Cancel]. Click "Tool" "BRI Automatic Configuration" from the menu bar. a. Click "Check" to turn on the BRI card. b.
  • Page 19 a. Type the Subscriber Number for the desired ports. b. Click [Execute]. ISDN line data such as P-P/P-MP, TEI Mode are automatically set. c. Click "Check Box" of the desired ports. d. Click [Data Apply]. e. Click [Close]. a. Double-click "Slot". b.
  • Page 20 For ISDN trunk user (MSN Setting): 1. Double-click "CO & Incoming Call". 2. Double-click "DIL Table & Port Setting". 3. Click the "DDI / DID / TIE / MSN" tab. 4. Set the "Incoming Type" of the desired ports to "MSN". 5.

  • Page 21: Confirming The Connection

    14. Double-click "Configuration". 15. Double-click "Extension Port". 16. Change the connection of the appropriate port to INS. 17. Click [OK]. Confirming the Connection Making Calls To call another extension extension no. Dial extension number. Talk. Off-hook. To call an outside party outside phone no.
  • Page 22 • Analogue Public Switched Telephone Network (PSTN) of a European country • Pan-European Integrated Services Digital Network (ISDN) using ISDN basic rate access We, Panasonic Communications Company (U.K.) Ltd., declare that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.