Page 1
ORDER NO. KM40107835C3 Telephone Equipment KX-T2371MXW Integrated Telephone System White Version (for Asia, Middle Near East and Other areas) SPECIFICATIONS...
3.2. Answering Calls 4. SPECIAL FEATURES 4.1. For Call Waiting Service Users...
Page 5
4.2. Temporary Tone Dialing (For Rotary Service Users) 4.3. How to Use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) 5. DISASSEMBLY INSTRUCTIONS...
Ref. No. Procedure Shown in Fig —. To remove —. Remove —. Lower Cabinet Screws (2.6 × 12)..... (A) × 5 1 ~ 2 Printed Circuit Board Remove the P.C.Board 6. HOW TO REPLACE FLAT PACKAGE IC 6.1. Preparation - SOLDER Sparkle Solder 115A-1, 115B-1 or Almit Solder KR-19, KR-19RMA - Soldering iron Recommended power consumption will be between 30 W to 40 W.
Page 7
the soldering iron. 6.3. Modification Procedure of Bridge 1. Re-solder slightly on bridged portion. 2. Remove remained solder along pins employing soldering iron as shown in below figure. 7. CPU DATA...
12. CIRCUIT OPERATIONS Note: The circuit diagram may be modified at any time with the development of new technology. 12.1. Telephone Line Interface and Pulse Dial Circuit When the hook switch SW1 is ON (off-hook), the circuit is closed, and current is supplied to the base of Q2 via the diode bridge D1 and Q2 is On Q1 is ON (OFF-HOOK condition).
Page 11
wave. The signal flow to the line is as follows. Pin 11 of IC1 Tel Line. The DTMF signal is sent to the line via the following path. Q9 and Q3 is an amplifier which is used to output the signal to line. Shown below is the signal flow used to output the DTMF signal from the handset as a monitor tone when a dial key is pressed.
12.3. Ringer Circuit Circuit Operation: The bell signal passes through C1 (R1) supplying power to pin 1 of IC2. The ring signal is output from Pin 5 of IC2, and its volume is adjusted in 3 steps (H-L-OFF) by SW3 then impressed on the ceramic sound generator, and so is generated. Output frequency is controlled by R2 and C3 following below formula.
12.6. Receiving Circuit (Rx) Receiving signal from the line go through Handset speaker. * Q4 and Q6 is amplifier for the Receiving signal. 13. TROUBLE SHOOTING GUIDE 13.1. Service Hints SYMPTOM CURE No Tone Dialing. Check IC1, Q3, Q9, R37, R38, R34 and R35. Dead.
13.4. Tone Dialing Problems 13.5. Problems With Ringer Check R1, C1, IC2, R3, C37, R2, C3, C2. 13.6. How to Check the IC1 (Scanning to the key) 14. CABINET AND ELECTRICAL PARTS LOCATION...
15. ACCESSORY AND PACKING MATERIALS 16. REPLACEMENT PARTS LIST This replacement parts list is KX-T2371MXW only. 1. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time.
Page 18
longer be available. 2. Important safety notice Components identified by the mark indicates special characteristics important for safety. When replacing any of these components, only use specified manufacture's parts. 3. The S mark indicates service standard parts and may differ from production parts.
17. FOR SCHEMATIC DIAGRAM (SCHEMATIC DIAGRAM) 1. DC voltage measurements are taken with electronic voltmeter from negative terminal. (Add 40 mA to telephone line from the loop simulator.) 2. This schematic diagram may be modified at any time with the development of new technology.
Page 24
PROGRAM PAUSE REDIAL FLASH AUTO SHARP Q182 Q183...
Page 25
SW25 E C B C186 R111 JJ102 C181 R184 C187 JJ101 POS1 E C B E C B [BREAK 60%] [BREAK 66%] RINGER H/S_JACK BLACK...
Page 26
TRANSISTOR VOLTAGE CHECK (MAIN PCB) VOLTAGE CHECK (IC2) MODE (TALK) (BELL) MODE (TALK) (BELL) PIN NO PARTS NO Emitter Collector Base Emitter Collector Base 7.69 32.0(AC) 8.43 8.25 7.72 0.56 0.45 0.37 8.77 23.1(AC) 0.00 0.10 0.65 0.00 0.37 0.34 8.41 23.1(AC) 5.08...