Related Manuals for Heartland WaveRider
Summary of Contents for Heartland WaveRider
- Page 1 WaveRider Installation Single Machine Side-Car Enclosure Coin & Card Pulse Mode TOP OF MACHINE MOUNTING www.heartlandMicroPayments.com 2115 Chapman Road, Suite 159, Chattanooga TN 37421 800.332.4835...
- Page 2 Laundry Machine Model Numbers This document applies to the WaveReader installation process following Dexter model numbers: Washers T-300..WCAD20KCS T-400..WCAD30KCS T-600..WCAD40KCS T-900..WCAD60KCS T-1200..WCAD80KCS If you cannot locate the model number of the machine you require in the lists above, please contact MicroPayments Customer Service at: Tel: 800-332-4835 Press 2 www.heartlandMicroPayments.com...
- Page 3 Installation Kit Contents & Required Tools This following tables list the required tools & components for the installation process. Required Tools #T-20 Pin-in-Star Torx Driver Phillips Head Screwdriver (med.) – magnetic tip is helpful Electric Drill – Heavy Duty ...
- Page 4 Interface Harness KIT-HRN-050-6-012 Harness Kit for Dexter Coin & Card Item Part Number Description AYS-050-6-012 Stuffed Dexter Coin Interface Board 2 – 2a Cable, Dexter Pulse for WR + Coin (2 – part) AYS-050-6-019 AYS-168110 110 VAC Transformer If you cannot locate and/or identify any of the components listed above, please contact MicroPayments Customer Service at 800-332-4835 , then press 2.
- Page 5 Side Car Housing KIT-050-6-040 Side-Car Enclosure Kit (Surface Mount) Item Part Number Description MFP-050-6-A040 Side Car Surface Mount Bottom MFP-050-6-032-011 Side Car Cover SRW-632X.375BTSS Screw 6-32 x 3/8"Button Torx Socket WAS-1/4-20L Washer 1/4-20 locking Nut ¼” – 20 Steel Hex NUT-4X20SH SRW-632X.188PPL Screw 6-32 x 3/16"...
-
Page 6: Installation
!! WARNING !! MAKE SURE THAT ALL POWER HAS BEEN REMOVED FROM THE MACHINE BEFORE ATTEMPTING TO INSTALL ANY HARDWARE OR CABLING! Preparation Disconnect the laundry machine from all power sources before performing any of the following steps. Installation Place the Side Car enclosure bottom on top of the Dexter top cover panel, and line it up as shown. - Page 7 Installation Locate the AC transformer supplied with the WaveReader installation kit. Connect the two spade lugs from the primary side of the transformer to the #2 and #5 lugs of the power distribution bar as shown. Locate the Dexter Interface Board supplied with the installation kit.
- Page 8 Installation Disconnect the exiting coin-drop connectors from the control board. Disconnect the white- bundled display cable from the control board. Connect the white- bundled Dexter display cable to the mating “To Display” connector on the Interface Board, as shown. www.heartlandMicroPayments.com...
- Page 9 (“Coin Drop / Coin Drop” on the Interface Board, as shown. Locate the WaveRider / Dexter display harness that was supplied with the installation kit. Connect one end (they are the same) to the ‘From Controller”...
- Page 10 Installation Connect the other end to the Dexter control board, as shown… Locate the WaveRider/Dexter interface harness supplied with the installation kit. It has multiple ends, as shown. Connect the 10-Pin, black connector of the WaveReader harness to the “Cable In”...
- Page 11 Installation Connect the 4-position white connector (it will have one green wire) of the WaveReader harness to the Dexter control board, at the same place that the coin-drop was disconnected from. Connect the 7-position white connector of the WaveReader harness to the Dexter control board, at the same place that the coin-...
- Page 12 Installation Securely mount the Interface Board in a suitable location , as shown. Mounting holes are provided for screws. Replace the machine’s top cover with the side-car bottom attached. Do not secure the top cover. With the top cover raised slightly, feed the WaveReader end of the cable harness through the hole in the side-car bottom.
- Page 13 Installation Secure the WaveReader to the top cover with the four (4) 6-32 Philips Pan Head Locking Screws that were supplied with the Side Car Kit. Connect the large, free end (J1) of the WaveReader harness that was pulled through the hole to the connector on the back of the reader.
-
Page 14: Finished Assembly
Installation Install the six (6) 6-32 x 3/8"Button Torx screws to secure the Side Car top cover to the bottom panel. There are three (3) per side. Finished assembly. Using zip-ties, secure all wiring harnesses to prevent pinching, wire-strain, and chafing. Apply the self-adhesive sticker that displays the accepted card brands (supplied) in a clearly... - Page 15 Testing Once the unit has been reassembled, the entire WaveReader needs to be tested before being IMPORTANT placed into or returned The WaveContoller has to be to service. operating and the machines linked to it before testing can be performed. 1.