Related Manuals for Heartland WaveReader
Summary of Contents for Heartland WaveReader
- Page 1 WaveRider Installation PULSE MODE COIN & CARD INTERNAL MOUNTING www.heartlandMicroPayments.com 2115 Chapman Road, Suite 159, Chattanooga TN 37421 800.332.4835...
- Page 2 Laundry Machine Model Numbers This document applies to the WaveReader installation process following Alliance/Speed Queen model numbers: Washers STEB77 (stack w/d) Dryers SSGT09 If you cannot locate the model number of the machine you require in the lists above, please contact MicroPayments Customer Service at: Tel: 800-332-4835 Press 2 www.heartlandMicroPayments.com...
- Page 3 Required Tools & Installation Kit Contents The tools required for the installation process are as follows #T-20 Pin-in-Star Torx Driver Phillips Head Screwdriver (medium) 3/16” Drill Bit 3/4” Drill Bit (or Step Drill bit to match) ...
- Page 4 This following tables list the required components for the installation process. If you cannot locate and/or identify any of the components listed above, please contact MicroPayments Customer Service at 800-332-4835 , then press 2. WaveReader Item Part Number Description WLAU-NNNNNN...
- Page 5 NUT-8X32SHKEP Nut, 8x32, Steel, Hex KEP Screw 6-32 Thread x 1/8” Pan-Head, Phillips SRW-632X.125PM There are two methods of installing a WaveReader (internally) into a coin & card laundry machine. They are: Internal Mounting – Trim Plate Kit ...
-
Page 6: Internal Mounting
Internal Mounting Minimum Required Dimensions Required Surface Area and Cutaway Openings = Required surface space = Cut/Drilled Opening Required Internal Depth Clearance .875” (3/4”) 4.0” www.heartlandMicroPayments.com... - Page 7 3” circular punch to remove the area marked by the dashed, interior circle [2]. After making the cut, attach the WaveReader to the Surface Mount Cover Plate (1) with the four screws (3) provided in the kit.
- Page 8 WaveReader. After making the cut and drilling the holes, attach the WaveReader to the machine with the four screws (3) provided in the kit. Do not fully tighten the screws.
- Page 9 HARDWARE OR CABLING! Preparation Disconnect the laundry machine from all power sources before performing any of the following steps. Only perform the following steps after the WaveReader has been physically installed in the machine. Remove all screws and fasteners so...
- Page 10 Installation After physical installation, the reader should look like this (with the Trim- Plate Kit). This a view from the side Connect J1 of the interface harness back of the WaveReader. www.heartlandMicroPayments.com...
- Page 11 Installation On the main panel, connect J3 of the WaveReader harness to the H5 connector on the Speed Queen control board, in the yellow box. On some Quantum control boards, the connector may be labeled H4. On the main panel,...
- Page 12 Installation Locate the Coin Adapter Board. Connect J4 of the WaveReader harness to the mating connector on the Coin Adapter Board. Connect the Coin Drop into the other side of the Coin Adapter Board. Locate the Serial Jumper on the control board and remove it.
- Page 13 Installation The completed wiring assembly should look like this… Wiring Diagram Using zip-ties, secure all wiring harnesses to prevent pinching, wire-strain, and chafing. www.heartlandMicroPayments.com...
-
Page 14: Finished Assembly
3.The Start Value Pulse ‘PLSE’ must be set to the same coin value as the WaveReader’s. Typically, this value is $.25. The programming steps for this are detailed in Step 23. www.heartlandMicroPayments.com... - Page 15 Installation PLSE Programming – special care should be paid to this setting. The modified excerpt below is from Speed Queen’s ‘MDC Frontload Washer Programming Manual’ and is provided for convenience. Please refer to your machine’s manual for confirmation. www.heartlandMicroPayments.com...
- Page 16 2. Verify that 25c is deposited into the machine 3. Swipe a card, wait for the transaction to be approved and then press START on the WaveReader 4. Verify that the balance of the funds have been deposited into the machine and it is ready to start.