Load Laundries; Use Of Detergent; Control Panel Instructions - Dawlance DWT 260 C LVS+ User Manual

Load laundries

The capacity of washing and spinning of the machine refer
to the largest weight of the standard laundries under dry
condition. Washing quantity shall be lower than the rated
capacity.
Different thickness, size and type of the laundries will
in uence the actual washing capacity. It is suitable that
the laundries can be turned round normally during washing.
Do not select high water level when laundries are less.

Use of detergent

Withdraw the dispenser box before adding detergent.
Pour concentrated synthetic washing powder into
Detergent box
The dosage of the washing powder, please refer to
below.
How to use the washing powder
How to use bleach
Fill water to the selected level,
dilute the bleach in the container,
and pour it slowly into the washing
tub.
Do not use bleach for colored or
gured laundries as they are prone
to lose colors.
Do not put bleach to laundries
directly.
Refer to the manual for the usage
and quantity of the bleach.
Please dissolve powder bleach
before use.
It is suggested to use low foam washing powder.
For the quantity of the concentrated washing powder, please refer to its manual.
Remarks: Avoid splashing of water and waste of washing powder, water level should not be too
high if laundries are too small.
Operation
the box directly as shown in the left illustration.
It is suggested to use low sud washing powder.
Dissolve in the machine directly not suitable for
preset program
1. Low water level.
2. Add the washing powder, and run for 30 seconds
to dissolve it completely.
3. Put laundries in, select suitable water level.
The instant dissolving of the washing powder
1. Prepare warm water of 30 in a container.
2. Pour the powder while stirring to fully dissolve it.
The washing powder is more prone to pollute the
laundries than the detergent, therefore, please use
it with proper quantity.
Washing powder with poor quality or not used for a
long period may get blocked, please clean the
detergent box in time.
09
Control panel instruction
Mode and meaning of the indicator light
On: Indicate the selected mode.
Flashing: Indicate the program is running.
Additional functions
At the beginning of start, pressing WATER LEVEL , at the same time press PRESET, you can select
WATER RECYCLE, LOW NOISE, LOW NOISE-WATER RECYCLE. Only both RINSE and SPIN are
selected, WATER RECYCLE can be selected. Once LOW NOISE is selected, program default setting
is NORMAL and PROGRAM button is locked.
During working, press WATER LEVEL and PRESET to set CHILD LOCK, press again to unlock
this function.
Use DIY program, you can set rinse times.
At the beginning of start, the rinse times setting is "2 times".
With DIY program, you can choose soak function and wash time.
Pressing " WASH" button for 2 seconds to choose soak function, pressing for
2 seconds again to cancel soak function.
Under "NORMAL", "HEAVY" programs to choose soak function, the soak is
before wash.
At the beginning of start, the wash time is "15 minutes".
At the beginning of start
Put power supply through, press " POWER" button, the washing machine is at the beginning of start:
1. If there is no water in inner tub, washing machine is in " FUZZY" condition, washing time is "15 minutes",
rinse time is "2 times", spin time is "7 minutes", water level and preset are displayed "--", program
is "NORMAL " If press "START/PAUSE" button ( or press "PROGRAM" to select "HEAVY
washing machine will start to sense and automatically sense the weight of laundries and set water level.
2. If there is water in inner tub, the washing machine is not in "FUZZY" condition, washing time is
"15 minutes", rinse time is "2 times", spin time is "7 minutes", water level is "7", program is "NORMAL
digital time displays the time to finish washing.
Soak (min.)
4
20
3
15
12 2
9 1 Spin (min.)
Wash Rinse Spin
Use DIY program,you can set spin time.
At the beginning of start , the spin time setting
is " 7 minutes".
At the beginning of start, you can press "SPIN"
to set spin process only, press "SPIN" again to
set spin time.
" ), the
10
9
7
5
3
" ,