All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG. Personnel qualification This description is only intended for trained specialists in control, automation and drive engineering who are familiar with the applicable national standards.
FF - K-bus firmware version HH - hardware version Example with ser. No.: 49 08 1B 03: 49 - week of production 49 08 - year of production 2008 1B - firmware version 1B 03 - hardware version 03 KL2784 und KL2794 Version: 2.0.0...
KL2784 - Introduction Fig. 1: KL2784 The KL2784 digital output terminal is able to switch voltages up to 24 V AC/DC using advanced MOSFET transistors. The semiconductor switches connected to the power contacts represent a substitute for relay contacts. They are short-circuit proof and free from wear, thereby increasing the availability of the application.
The output is short-circuit-proof to a limited extent. The output transistor can cope with short-term overcurrents until the fuse is triggered. The Bus Terminal has four channels, whose signal state is displayed by LEDs. KL2784 und KL2794 Version: 2.0.0...
35 mm mounting rail conforms to EN 60715 Vibration / shock resistance conforms to EN 60068-2-6 / EN 60068-2-27 EMC immunity / emission conforms to EN 61000-6-2 / EN 61000-6-4 Protection class IP20 Pluggable wiring for all KSxxxx terminals Correct installation position variable Approvals CE, cULus [} 20], ATEX Version: 2.0.0 KL2784 und KL2794...
Signal LED 1 Output 1 switched off Output 1 switched on Signal LED 2 Output 2 switched off Output 2 switched on Signal LED 3 Output 3 switched off Output 3 switched on Signal LED 4 Output 4 switched off Output 5 switched on KL2784 und KL2794 Version: 2.0.0...
To mount the mounting rails with a height of 7.5 mm under the terminals and couplers, you should use flat mounting connections (e.g. countersunk screws or blind rivets). Version: 2.0.0 KL2784 und KL2794...
PE power contact The power contact labeled PE can be used as a protective earth. For safety reasons this contact mates first when plugging together, and can ground short-circuit currents of up to 125 A. KL2784 und KL2794 Version: 2.0.0...
Power Feed Terminals can be released and pulled at least 10 mm from the group of terminals. Risk of electric shock! The PE power contact must not be used for other potentials! WARNING Version: 2.0.0 KL2784 und KL2794...
The familiar dimensions of the terminal only had to be changed slightly. The new connector adds about 3 mm. The maximum height of the terminal remains unchanged. KL2784 und KL2794 Version: 2.0.0...
Ultrasonically “bonded" conductors It is also possible to connect the Standard and High Density Terminals with ultrasonically "bonded" (ultrasonically welded) conductors. In this case, please note the tables concern- Note ing the wire-size width below! Version: 2.0.0 KL2784 und KL2794...
The cables are released, as usual, using the contact release with the aid of a screwdriver. See the following table for the suitable wire size width. KL2784 und KL2794 Version: 2.0.0...
Risk of injury through electric shock and damage to the device! Bring the Bus Terminals system into a safe, de-energized state before starting mounting, disassembly or wiring of the Bus Terminals! WARNING Fig. 11: KL2784 - Connection Terminal No.: Connection for point...
• EN 60079-0:2012+A11:2013 • EN 60079-15:2010 Marking The Beckhoff fieldbus components with standard temperature range certified for potentially explosive areas bear one of the following markings: II 3G KEMA 10ATEX0075 X Ex nA IIC T4 Gc Ta: 0 … 55°C II 3G KEMA 10ATEX0075 X Ex nC IIC T4 Gc Ta: 0 … 55°C Version: 2.0.0...
Notes about operation of the Beckhoff terminal systems in potentially explo- sive areas (ATEX) Pay also attention to the continuative documentation Note Notes about operation of the Beckhoff terminal systems in potentially explosive areas (ATEX) that is available in the download area of the Beckhoff homepage http:\\www.beckhoff.com! KL2784 und KL2794...
Beckhoff's branch offices and representatives Please contact your Beckhoff branch office or representative for local support and service on Beckhoff products! The addresses of Beckhoff's branch offices and representatives round the world can be found on her internet pages: http://www.beckhoff.com You will also find further documentation for Beckhoff components there.
Page 23
Fig. 7 Standard wiring..........................Fig. 8 Pluggable wiring .......................... Fig. 9 High Density Terminals........................ Fig. 10 Connecting a cable on a terminal point ..................Fig. 11 KL2784 - Connection ........................Fig. 12 KL2794 - Connection ........................KL2784 und KL2794 Version: 2.0.0...