Brake actuated hydraulically in a floating caliper design serving to generate a brake force on a brake disk in order to decelerate a machine's movement or stop it, respectively, or keep it at standstill. (23 pages)
Page 1
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 1 of 8 Operating/Assembly instructions Edition: ® ® CLAMPEX KTR 125 CLAMPEX KTR 125.1 ® The CLAMPEX clamping set is a frictionally engaged, detachable shaft-to-shaft connection for cylin- drical shafts and bores without feather key. Table of contents Technical data Advice...
Page 2
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 2 of 8 Operating/Assembly instructions Edition: Technical data Dimension D : For calculation of hub see catalogue "Drive Tech- ® Illustration 1: CLAMPEX KTR 125 nology" ® Table 1: CLAMPEX KTR 125 Groove nut DIN 981 Transmittable torque or...
Page 3
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 3 of 8 Operating/Assembly instructions Edition: Technical data Dimension D : For calculation of hub see catalogue "Drive Tech- ® Illustration 2: CLAMPEX KTR 125.1 nology" ® Table 2: CLAMPEX KTR 125.1 Groove nut DIN 981 Transmittable torque or...
Page 4
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 4 of 8 Operating/Assembly instructions Edition: Advice 2.1 General advice Please read through these operating/assembly instructions carefully before you mount the clamping set. Please pay special attention to the safety instructions! The operating/assembly instructions are part of your product.
Page 5
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 5 of 8 Operating/Assembly instructions Edition: Storage, transport and packaging 3.1 Storage The clamping sets are supplied in preserved condition and can be stored at a dry and roofed place for 6 - 9 months.
Page 6
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 6 of 8 Operating/Assembly instructions Edition: Assembly 4.2 Assembly of the clamping set Inspect the fit of shaft and hub for the tolerance specified (illustration 3). Clean the surfaces of the clamping set marked in illustration 6 as well as of shaft and hub and afterwards ap- ply thin fluid oil lightly (e.
Page 7
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 7 of 8 Operating/Assembly instructions Edition: Assembly 4.3 Disassembly of clamping set Disassembly of KTR 125.1: The clamping set KTR 125.1 is self-locking. You may expect an excessively difficult dis- assembly.
Page 8
® CLAMPEX KTR-N 40811 EN KTR 125 / KTR 125.1 Sheet: 8 of 8 Operating/Assembly instructions Edition: Advice regarding the use in hazardous locations according to ATEX 95 If used in hazardous locations the type and size of clamping set (for category 3 only) has to be selected such that the difference between the peak torque of the machine including all operating parameters and the rated torque of the clamping hub at least corresponds to a safety factor of s = 2.
Need help?
Do you have a question about the CLAMPEX KTR 125 and is the answer not in the manual?
Questions and answers