Curt Manufacturing 2060 Installation Instructions

INSTALLATION INSTRUCTIONS

PARTS LIST:

1 Grille Guard
1 Driver/Left Side Mounting Bracket
1 Passenger/Right Mounting Bracket
1 Driver/Left Top Bracket
1 Passenger/Right Top Bracket
4 12-1.75mm x 35mm Hex Head Bolts
4 12mm Lock Washers
4 12mm ID x 30mm OD x 3mm Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION.
2. WARNING! This Grille Guard is designed to swivel forward by partially unfastening the upper and lower
bolt on the Grille Guard when the hood needs to be opened for service. Make sure that all hardware is
fully tightened after closing the hood. Read page 3 opening and closing of hood before installing Grille
Guard.
3. From underside of vehicle remove the factory tow hooks and set aside.
4. Determine Driver/Left and Passenger/Right Mounting Bracket. Refer to Figure 1 for bracket configuration.
5. Hang Driver/Left side Mounting Bracket into position by partially threading the two factory bolts (Figure 2). NOTE:
Tow hooks can be re-mounted by placing them on top of Mounting Brackets. Use the same factory bolts to re-
mount factory tow hooks and Mounting Brackets. Repeat this step for opposite side.
6. Open the hood and remove the driver/left side plastic fasteners located right next to the bump stopper (Figure 3).
7. Carefully pull up on the factory color grille shell, about where the Driver/Left bump stopper is located. Slide
through Driver/Left Top Bracket between bumper and color grille shell (Figure 4). NOTE: When you pull up on the
color grille shell, you are going to notice some plastic tabs on the bottom of the color grille shell. Slide Top Bracket
through the gap between these tabs, and then slide Top Bracket over to its mounting location.
8. Align inner hole on the Top Bracket to the previously removed plastic fastener location. Attach Top Bracket to
vehicle using the included (1) 8mm x 45mm Hex Head Bolt, (1) 8mm Nylock Nut, and (2) 8mm Flat Washers
(Figure 5 & 6). Do not tighten at this time.
9. Repeat steps 6 - 8 for Passenger/Right Top Bracket.
10. With help position Grille Guard on the outer side of Mounting and Top Brackets. Attach Grille Guard to Mounting
Brackets using the included (4) 12mm Hex Head Bolts, (4) 12mm Lock Washers, and (4) 12mm Flat Washers
(Figure 2). Do not tighten at this time.
11. Attach Grille Guard to Top Brackets using the included (2) 10mm x 30mm Button Head Allen Bolts, (2) 10mm
Nylock Nuts, and (4) 10mm Flat Washers (Figure 7). Do not tighten at this time. NOTE: Insert Button Head Allen
Bolt through the outer side of Grille Guard.
12. Pull the Grille Guard towards the front of the vehicle to its open position (Figure 11). Center and level Grille Guard
and then tighten all hardware at this time.
13. Close hood, and then partially loosen the bolt on each Top Bracket and the upper bolt on each lower Mounting
Bracket (Figure 9 & 10). WARNING! Do not loosen bolts all the way. Damage to the truck or Grille Guard may
occur.
14. Push Grille Guard back as close as possible towards the vehicle, and then tighten all hardware.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
GRILLE GUARD
07 TOYOTA TUNDRA
PART NUMBER 2060/2060-2
2 10-1.50mm x 30mm Button Head Allen Bolts
2 10mm Nylock Nuts
4 10mm ID x 30mm OD x 3mm Flat Washers
2 8-1.25mm x 45mm Hex Head Bolts
2 8mm Nylock Nuts
4 8mm ID x 22mm OD x 1.5 Flat Washers
Page 1 of 3 4/9/07 (AM)