Wired Lan Settings [Cx10] - Panasonic AG-CX7 Operating Instructions Manual

0 When [DHCP] is set to [CLIENT], some of the information acquired automatically with DHCP is displayed in the menu.
For details of the network status, confirm by selecting the [NETWORK] menu → [INFORMATION] → [STATUS].
0 All of the IP address, subnet mask, and default gateway must be correctly set.
For details, contact the network administrator.
0 When the default gateway or DNS is not to be used, set to [0.0.0.0].
However, DNS cannot be disabled when [DHCP] is set to [CLIENT].
0 Depending on the network environment, even if [DHCP] is set to [CLIENT], entry of the DNS value manually may be required. When invalid DNS value
is entered in any other cases, the automatic assignment by DHCP will not operate properly.

Wired LAN settings [CX10]

These are the settings when using a wired LAN.
1
Select the [NETWORK] menu → [DEVICE SEL] → [USB-LAN].
2
In [NETWORK] menu → [USB-LAN IPv4 SETTING] and [USB-LAN IPv6 SETTING], set each item as required.
≥ For the setting items, refer to "Setting items for [USB-LAN IPv4 SETTING], and [USB-LAN IPv6 SETTING] when set to [USB-LAN]" (l 177).
3
Close the menu or return to the level of the [NETWORK] menu.
4
Configure the settings of the wired LAN on your device such as a computer.
For more information, refer to the operating instructions or help for the connection device.
∫ Setting items for [USB-LAN IPv4 SETTING], and [USB-LAN IPv6 SETTING] when set to [USB-LAN]
[USB-LAN IPv4 SETTING]
[USB-LAN IPv6 SETTING]
@
NOTE
0 Some items cannot be selected depending on the settings such as [DHCP].
0 The startup time after turning on the power may be longer due to starting of the network.
0 When changing the settings of [DEVICE SEL], the changes will not be reflected until the unit is restarted. Also, the setting screen termination may take
some time due to the restart of the network service after the setting is changed.
0 All of the IP address, subnet mask, and default gateway must be correctly set.
For details, contact the network administrator.
0 Set [0.0.0.0] or [::] when not using the default gateway or DNS.
However, DNS cannot be disabled when [DHCP] is set to [CLIENT].
0 Depending on the network environment, even if [DHCP] is set to [CLIENT], entry of the DNS value manually may be required. When invalid DNS value
is entered in any other cases, the automatic assignment by DHCP will not operate properly.
0 DHCP and DNS may not function properly depending on the network environment.
0 The IP address cannot be automatically acquired depending on the connection timing with network devices if [USB-LAN IPv6 SETTING] → [DHCP] →
[CLIENT] is set.
In this case, reconnect the LAN cable or contact your network administrator.
Chapter 9 Network Connection — Network settings
[DHCP]
[IP ADDRESS]
[SUBNET MASK]
[DEFAULT GATEWAY]
[PRIMARY DNS]
[SECONDARY DNS]
[ENABLE/DISABLE]
[DHCP]
[IP ADDRESS]
[PREFIX LENGTH]
[DEFAULT GATEWAY]
[PRIMARY DNS]
[SECONDARY DNS]
Setting the DHCP function
≥ [OFF]: Does not use DHCP.
≥ [CLIENT]: Acquires automatically with DHCP.
≥ [SERVER]: Enables the DHCP server function of the unit.
(Factory setting: [OFF])
IP address of the unit
(Factory setting: [192.168.0.1])
Subnet mask
(Factory setting: [255.255.255.0])
Default gateway
(Factory setting: [192.168.0.254])
Primary DNS server setting
(Factory setting: [0.0.0.0])
Secondary DNS server setting
(Factory setting: [0.0.0.0])
IPv6 setting
≥ [ENABLE]: Uses IPv6.
≥ [DISABLE]: Does not use IPv6.
(Factory setting: [DISABLE])
Setting the DHCP function
≥ [OFF]: Does not use DHCP.
≥ [CLIENT]: Acquires automatically with DHCP.
(Factory setting: [OFF])
IP address of the unit
(Factory setting: [::])
Prefix length settings of the subnet
(Factory setting: [64])
Default gateway
(Factory setting: [::])
Primary DNS server
(Factory setting: [::])
Secondary DNS server
(Factory setting: [::])
- 177 -