Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Cornelius LOOP STYLE XL CC
- Page 1 LOOP STYLE XL CC...
- Page 2 LOOP Style XL CC Manual operation English Legal notice Document no.: TD1009600EN Countertop Vending Machine Model LOOP Style XL CC Version Date of issue: 24.09.2019 Revision status: Index 0 Protection notices (in accordance with DIN ISO 16016:2002-5) The reproduction, distribution and utilization of this document as well as the communication of its contents are prohibited, unless expressly permitted.
-
Page 3: Table Of Contents
LOOP Style XL CC Table of Contents Safety ................................4 Intended use ............................. 4 Improper use ............................. 4 Staff ................................5 1.3.1 Operator ............................5 1.3.2 User ..............................5 1.3.3 Expert ..............................5 Presentation of warning ..........................5 Safety instructions ............................ 5 1.5.1... -
Page 4: Safety
1.2 Improper use Improper use of the unit and unauthorized modifications to the unit and its components may cause personal injury and equipment damage for which Cornelius Deutschland GmbH shall assume no liability. Improper use of the unit is prohibited. -
Page 5: Staff
An expert must also have received technical training in the unit-specific special features of Cornelius products. The assigned tasks are always to be carried out in compliance with this manual. -
Page 6: Disclaimer Of Liability And Warranties
LOOP Style XL CC Disclaimer of liability and warranties If work is undertaken on the unit which is not described in this document, Cornelius Deutschland GmbH shall not assume any liability for any resulting hazards and damages. The same applies to described work which is partly or not fully performed in compliance with the regulations set out in this document. -
Page 7: Transport And Packaging
(e.g. EN 60335-2-75). Transport and packaging Choose a suitable packaging when returning the unit itself or one of its components to Cornelius Deutschland GmbH, e.g. for repairs. In particular, make sure that the unit and any components are protected from shock/impact, moisture, dirt and electrostatic discharge (ESD). -
Page 8: Disposal
LOOP Style XL CC Caution! Damage due to improper storage Dirt or moisture entering a unit, as well as certain weather conditions (e.g. condensate forming at the unit, sunlight) will cause damage to the unit and its components. • Protect the unit and its components by storing the unit in a clean and dry place, and by ensuring stable ambient conditions. -
Page 9: Installation Requirements
LOOP Style XL CC Installation Requirements 4.1 Installation Sites Comply with the valid national regulations for installation sites and electrical connections. Ventilation of the installation sites must be appropriate for unit output. Inadequate ventilation of the unit will result in overheating and damage. -
Page 10: Installation
LOOP Style XL CC Installation The unit must be installed by a trained service technician. Please take care, that the socket for the unit is always accessible. If the power supply cable to the unit is damaged, it has to be replaced by the manufacturer, the service partner or any other qualified person to avoid safety hazard. -
Page 11: Putting Into And Out Of Operation
LOOP Style XL CC Putting into and out of Operation 6.1 Putting into Operation Before starting operation of the unit the transport lock must be removed. In order to ensure the proper function of the unit, please follow the below outlined points in their order. -
Page 12: Purging The Syrup Systems
LOOP Style XL CC bank mode. After the cooling system is switched on the running time is no less than 5 minutes. Switch off signals will be ignored in this time. After the cooling system switches off, the delay is no less than 3 minutes. -
Page 13: Taking Out Of Operation (Vacation, End Of Season)
LOOP Style XL CC 6.7 Taking out of operation (Vacation, end of season) Perform the following steps in case of protracted standstill periods: Close the CO -cylinder, the CO -stopcocks on pressure regulators and the water feed line. -
Page 14: Cleaning And Disinfection Procedure Before Use
LOOP Style XL CC 7.2 Cleaning and Disinfection Procedure before use In order to achieve a proper hygienic performance of the dispense equipment, it is crucial to run the initial and recurring sanitization procedure (intervals according to DIN 6650-6) on all product and water lines of the system. - Page 15 LOOP Style XL CC A.) Flushing-in of sanitization agent (e.g. P3 Ansep CIP from Ecolab) Syrup Lines 1.1) The product lines filled with syrup must first be flushed with water. For this an external water distributor can be used to connect and flush several syrup lines simultaneously.
- Page 16 LOOP Style XL CC B.) Flushing-out of sanitization agent Syrup Lines 1.1) Disconnect the cleaning tank and bring out any remaining sanitizing agent from the syrup lines by using CO gas. Afterwards close the CO supply and depressurize the system via the dispense valves.
-
Page 17: Problems And Troubleshooting
LOOP Style XL CC Problems and Troubleshooting Before seriously troubleshooting the dispense equipment, first check: Is the electricity to the unit interrupted? Are the beverage containers empty? Is the CO -cylinder empty? Are all valves on CO -cylinder open? -
Page 18: Technical Data
LOOP Style XL CC Technical Data Output capacity soft drink 0,2/0,3 liters Peak dispense at 2 drinks per minute 322 (0,3 l) Continuously – drinks per hour 75 (0,3 l) Supply voltage 230V/50Hz Power consumption in Watt Compressor output in Watt (HP)*... -
Page 19: Flow Chart
LOOP Style XL CC 10 Flow Chart LOOP STYLE XL 5 Valve 0,2 – 0,24 MPa (2-2,4 bar) 0,35-0,45 MPa ( 3,5-4,5 bar ) 0,35-0,4 MPa ( 3,5-4,0 bar) 0,05-0,1 MPa K( 0,5-1 bar ) LOOP STYLE XL 6 Valve... -
Page 20: Circuit Diagram
LOOP Style XL CC 11 Circuit Diagram Cornelius Deutschland GmbH Manual operation Countertop Vending Machine Document no: TD1009600EN LOOP Style XL CC Version A, 24.09.2019, Index 0 Page 20... -
Page 21: Exploded View / Sprengzeichnung
LOOP Style XL CC 12 Exploded View / Sprengzeichnung LOOP STYLE XL POM Cornelius Deutschland GmbH Manual operation Countertop Vending Machine Document no: TD1009600EN LOOP Style XL CC Version A, 24.09.2019, Index 0 Page 21... -
Page 22: Spare Part List / Ersatzteilliste
LOOP Style XL CC 13 Spare Part List / Ersatzteilliste Pos. Part-No. Benennung Description 220098287 Verflüssiger mit Lüftermotor Condenser with Fan Motor 220110873 Halteblech Verflüssiger Bracket Condenser 440000105 Rührwerkmotor Agitator 220110759 Halteblech Rührwerk Bracket Agitator 220110758 Traverse Traverse 220110750... -
Page 23: Declaration Of Conformity
LOOP Style XL CC 14 Declaration of Conformity Cornelius Deutschland GmbH Manual operation Countertop Vending Machine Document no: TD1009600EN LOOP Style XL CC Version A, 24.09.2019, Index 0 Page 23...
Need help?
Do you have a question about the LOOP STYLE XL CC and is the answer not in the manual?
Questions and answers