Advertisement

Quick Links

FOR QUALIFIED INSTALLER ONLY. This basic Installation Sheet is an initial release. If a complete Operations
Manual (for the unit being installed) is required or needed, please refer to the Lancer web site (lancercorp.com) for
immediate access, or for your convenience, scan this QR code with a mobile device (app required) for immediate
access to other Technical Documents and alternative translations (if available) pertaining to this unit. Contact Lancer
Customer Service for assistance as required.
ABOUT THIS MANUAL
This booklet is an integral and essential part of the product and
should be handed over to the operator after the installation and
preserved for any further consultation that may be necessary.
Please read carefully the guidelines and warnings contained
herein as they are intended to provide the user with essential
information for the continued safe use and maintenance of the
product. In addition, it provides GUIDANCE ONLY to the user on
the correct services and site location of the unit.
The installation and relocation, if necessary, of this product must be carried out by qualified personnel with
up-to-date safety and hygiene knowledge and practical experience, in accordance with current regulations.
IMPORTANT SAFETY INSTRUCTIONS
! Intended Use
The dispenser is for indoor use only. This unit is not a toy. Children should not be supervised not to play with appliance. It should
not be used by children or infirm persons without supervision. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety. Cleaning and user maintenance
shall not be performed by children without supervision. The min/max ambient operating temperature for the dispenser is 40°F to
105°F (4°C to 41°C). Do not operate unit below minimum ambient operation conditions. Should freezing occur, cease operation of
the unit and contact authorized service technician. Service, cleaning and sanitizing should be accomplished only by trained
personnel. Applicable safety precautions must be observed. Instruction warnings on the product being used must be followed.
! Automatic Agitation
Units are equipped with an automatic agitation system and will activate unexpectedly. Do not place hands or foreign objects in the
ice bin. Unplug the dispenser during servicing, cleaning, and sanitizing. To avoid personal injury, do not attempt to lift the dispenser
without assistance. For heavier dispensers, use a mechanical lift.
4800
Sensation 30
LANCER INSTALLATION GUIDE
BEFORE GETTING STARTED
Each unit is tested under operating conditions and is thoroughly
inspected before shipment. At the time of shipment, the carrier
accepts responsibility for the unit. Upon receiving the unit,
carefully inspect the carton for visible damage. If damage exists,
have the carrier note the damage on the freight bill and file a
claim with carrier. Responsibility for damage to the dispenser lies
with the carrier.
LANCER PN: 28-0885/04

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sensation 30 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for lancer Sensation 30

  • Page 1 FOR QUALIFIED INSTALLER ONLY. This basic Installation Sheet is an initial release. If a complete Operations Manual (for the unit being installed) is required or needed, please refer to the Lancer web site (lancercorp.com) for immediate access, or for your convenience, scan this QR code with a mobile device (app required) for immediate access to other Technical Documents and alternative translations (if available) pertaining to this unit.
  • Page 2: Specifications

    READ THIS MANUAL This manual was developed by the Lancer Corporation as a reference for the owner/operator and installer of this dispenser. Please read this guide before installation and operation of this dispenser. If service is required please call your Lancer Service Agent or Lancer Customer Service.
  • Page 3: Installation

    NOTE NOTE Lancer does NOT recommend the use of shaved or If unit is to be transported, it is advisable to leave the flake ice in the dispenser. The ice level should not unit secured to the plywood shipping base.
  • Page 4: Dispenser Installation

    An adapter plate is required when installing an icemaker. A. Oetiker Pliers Contact your Sales Representative or Lancer Customer B. Tubing Service for more information. C. Syrup/Water Inlet A bin thermostat is required in order to control the level of ice Route appropriate tubing from the remote carbonator to the in the dispenser (Refer to ATTENTION above).
  • Page 5: Dispenser Setup

    Installing CO Supply Dispenser Setup Connect high pressure CO regulator assembly to CO Turn on water source. cylinder or bulk system. Open the pressure relief valve, located on the remote ! ATTENTION carbonator, by flipping up on the valve cap lever. Hold open until water flows from the relief valve then close (flip down) Before installing regulator, assure that a seal (washer the relief valve.
  • Page 6: Adjust Water Flow Rate & Syrup/Water Ratio

    Use a screwdriver to adjust if needed. A. Water ON B. Syrup Closed Using a Lancer ratio cup verify water flow rate (5 oz. in 4 sec.). Use a screwdriver to adjust if needed. A. Syrup Seperator B. Ratio Cup C.
  • Page 7: Cleaning And Sanitizing

    CLEANING AND SANITIZING GENERAL INFORMATION Lancer equipment (new or reconditioned) is shipped from the factory cleaned and sanitized in accordance with NSF guidelines. The operator of the equipment must provide continuous maintenance as required by this manual and/or state and local health department guidelines to ensure proper operation and sanitation requirements are maintained.
  • Page 8 Cleaning and Sanitizing Nozzles Remove or melt out any remaining ice from the ice bin. Use a screwdriver to remove the Auger Motor shaft cover. Disconnect power, so as to not activate valve while cleaning. Remove the “C” clip from the Auger Motor Shaft. Remove merchandiser to reveal valves.
  • Page 9: Plumbing Diagram

    14. Remove the Ice Chute Assembly by removing four (4) 25. Repeat Step 24 for all exterior surfaces of the dispenser. screws that secure to unit and set aside. 26. Wearing sanitary gloves, reassemble all removable parts. 15. Remove Auger by pulling straight out from unit and set aside. Ensure agitator clip is locked.
  • Page 10: Wiring Diagrams

    WIRING DIAGRAMS Sensation 30 115 Volt Wiring Diagram...
  • Page 11: Dip Switch Legend

    SW1 SWITCH 2: "LOW ICE" ALARM ENABLED 7 SECONDS 5 SECONDS LANCER PN: 06-3289 Dispenser Disposal   To prevent possible harm to the environment from improper disposal, recycle the unit by locating an authorized recycler or contact the retailer where the product was purchased.
  • Page 12 Lancer Corp. 800-729-1500 Technical Support/Warranty: 800-729-1550 custserv@lancercorp.com lancercorp.com...

Table of Contents