Taylor C708 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Taylor Manuals
  4. Ice Cream Maker
  5. Wawa C708
  6. Operating instructions manual

Taylor C708 Operating Instructions Manual

Heat treatment soft serve freezer
Hide thumbs Also See for C708:
Table of Contents

Advertisement

Quick Links

Models C708 & C716
Heat Treatment
Soft Serve Freezer
Operating Instructions
059061- -M
6/17/08

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C708 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Taylor C708

Summary of Contents for Taylor C708

  • Page 1 Models C708 & C716 Heat Treatment Soft Serve Freezer Operating Instructions 059061- -M 6/17/08...
  • Page 2 All rights reserved. 059061--M Taylor Company a division of Carrier Commercial Refrigeration, Inc. The word Taylor and the Crown design 750 N. Blackhawk Blvd. are registered trademarks in the United States Rockton, IL 61072 of America and certain other countries.

  • Page 3: Table Of Contents

    ............Model C708 Single Spout Door and Beater Assembly .
  • Page 4 All rights reserved. 059061-M Taylor Company a division of Carrier Commercial Refrigeration, Inc. The word Taylor and the Crown design 750 N. Blackhawk Blvd. are registered trademarks in the United States Rockton, IL 61072 of America and certain other countries.

  • Page 5: To The Installer

    Failure to follow this instruction may result in Uncrate the unit and inspect it for damage. Report personal injury or death from electrical shock or any damage to your Taylor Distributor. hazardous moving parts as well as poor performance or damage to the equipment.

  • Page 6: Air Cooled Units

    NEC code is the practical safeguarding of persons and property from hazards Model C708: Requires a minimum of 6” (152 mm) of arising from the use of electricity. This code contains clearance on both sides and 0” in the rear of the provisions considered necessary for safety.

  • Page 7: Beater Rotation

    15 minutes. Cap all open tubing to located: C708 - behind the rear panel. prevent humid air or water from being absorbed by C716 - behind the lower front panel.

  • Page 8: To The Operator

    Taylor parts, purchased from an technician he employs. authorized Taylor Distributor, and the required It should also be noted that Taylor does not warrant service work is provided by an authorized Taylor the refrigerant used in its equipment. For example, if service technician.

  • Page 9: Safety

    We at Taylor Company are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture DO NOT operate the freezer unless it is built-in safety features to protect both you and the properly grounded.
  • Page 10 DO NOT obstruct air intake and discharge openings: severe personal injury from hazardous moving parts. C708: A minimum of 6” (152 mm) air space is required on both sides and 0” on the rear. C716: A minimum of 3” (76 mm) air space is This unit has many sharp edges that can required on all sides.

  • Page 11: Operator Parts Identification

    PANEL A.-FRONT-UPPER X59423 COVER-HOPPER *BLACK 053809-1 PANEL A.-FRONT-LOWER X58955 BLADE A.-AGITATOR X56591 STUD-NOSE CONE 055987 PUMP A.-MIX SIMPLIFIED S.S. X57029-14 SHELF-TRAY-DRIP 056076 PANEL-REAR 056077 TRAY-DRIP 056858 PAN A.-DRIP 5 1/2” LONG X56074 SHIELD-SPLASH 049203 Models C708 & C716 Operator Parts Identification...

  • Page 12: Model C716

    PUMP A.-MIX SIMPLIFIED X57029-14 SHIELD-SPLASH-WIRE-19-3/4 L 033813 PANEL-SIDE-RIGHT 059907 PAN-DRIP 19-1/2 LONG 035034 PANEL A.-FRONT X63879 STUD-NOSE CONE 055987 PANEL A.-FRONT X59836 PIN-RETAINING-HOPPER CVR 043934 PAN-DRIP 12.5 059736 PANEL-SIDE-LEFT 059906 FILTER-AIR-POLY-FLO 052779-11 061228 Operator Parts Identification Models C708 & C716...

  • Page 13: Model C708 Single Spout Door And Beater Assembly

    Model C708 Single Spout Door and Beater Assembly Figure 3 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. HANDLE A.-DRAW-WELDED X56246 SHOE-FRONT HELIX *FRONT* 050347 NUT-STUD-BLACK 2.563“ 058764 BEATER A.-3.4QT-1 PIN X46231 DOOR A.-W/BAFFLE X57332-SER BLADE-SCRAPER-PLASTIC 046235 VALVE A.-DRAW X55820 CLIP-SCRAPER BLADE 7.00...

  • Page 14: Model C716 Door And Beater Assembly

    SHAFT-BEATER 032564 O-RING--7/8 OD X .103W 014402 SEAL-DRIVE SHAFT 032560 VALVE A.-DRAW X59888 O-RING-1/4 OD X .070W 50 015872 VALVE A.-DRAW*CENTER X59890 SCREW-ADJUSTMENT-5/16-24 056332 SHOE-FRONT HELIX *FRONT* 050347 SEAL-DRAW VALVE H-RING 034698 080805 Operator Parts Identification Models C708 & C716...

  • Page 15: X57029-Xx Pump A. - Mix Simplified (Model C708)

    X57029-XX Pump A. - Mix Simplified (Model C708) Figure 5 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 - 7 PUMP ASSEMBLY - MIX X57029-14* PIN - COTTER 044731 SIMPLIFIED SOFT SERVE SHAFT A.-DRIVE-MIX PUMP- X41947 CYLINDER-PUMP-HOPPER- 057943 HOPPER...

  • Page 16: X57029-Xx Pump A. - Mix Simplified (Model C716)

    *NOTE: THE STANDARD PUMP X57029-XX IS -14. OVERRUN CAN BE CHANGED HIGHER OR LOWER BY SUBSTITUTING THE CAP (056874-XX) WITH CAPS AVAILABLE -1 THROUGH -20. THE HIGHER THE DASH (-) NUMBER, THE HIGHER THE OVERRUN. Operator Parts Identification Models C708 & C716...

  • Page 17: Accessories

    PAIL-MIX 10 QT. 013163 TOOL-O-RING REMOVAL 048260-WHT KIT A.-TUNE-UP (C708) X56085 TOOL-SHAFT-DRIVE-PUMP- 057167 KIT A.-TUNE-UP (C716) X49463-82 HOPPER KIT A.-PARTS TRAY (C708) X57797 LUBRICANT-TAYLOR HI-PERF 048232 KIT A.-PARTS TRAY (C716) X58449 *NOT SHOWN 060629 Models C708 & C716 Operator Parts Identification...

  • Page 18: Brush Kit Assembly X44127

    BRUSH SET (3) 050103 WHITE BRISTLE BRUSH 1” x 2” 013073 YELLOW BRISTLE BRUSH 039719 WHITE BRISTLE BRUSH 014753 WHITE BRISTLE BRUSH 3” x 7” 023316 1-1/2” x 3” PUMP SPOUT BRUSH 054068 Operator Parts Identification Models C708 & C716...

  • Page 19: Important: To The Operator

    Important: To the Operator C708 C716 Figure 9 ITEM DESCRIPTION POWER SWITCH LIQUID CRYSTAL DISPLAY KEYPADS MIX OUT INDICATOR STANDBY INDICATOR MIX LOW INDICATOR SELECT KEY SERVICE MENU KEY BRUSH CLEAN COUNTER ARROW KEY(S) Models C708 & C716 Important: To the Operator...

  • Page 20: Symbol Definitions

    = MIX LOW Reset Mechanism The reset button is located in the service panel on the left side of the C708. The reset buttons are = MIX OUT located in the back panel of the C716. A reset button protects the beater motor from an overload condition.

  • Page 21: Operating Screen Descriptions

    Air/Mix Pump Reset Mechanism Note: The displays illustrated in this section are those seen on the Models C708/C709. The Model This reset button protects the pump from an C716/C717 versions may vary slightly.
  • Page 22 While the Lockout Data is displayed. being checked, the following screen is displayed. POWER SWITCH OFF Initializing - = - = - = - = - = - Lockout Data UNIT CLEANED 050628 Important: To the Operator Models C708 & C716...
  • Page 23 Operator Manual. Failure to follow these machine can successfully enter the HEAT mode of guidelines will cause the control to lock the freezer operation. out of the AUTO mode. 050628 Models C708 & C716 Important: To the Operator...

  • Page 24: Freezer Locks

    HEAT CYCLE initiates a Heat Cycle SERVICE REQ'D immediately. Selecting BRUSH CLEAN when the > BRUSH CLEAN previous message is displayed will hard lock the machine and brush cleaning will be necessary. 080222 Important: To the Operator Models C708 & C716...
  • Page 25 Note: A record of Heat Cycle Data and Lock Out completed a heat treatment cycle. History can be found in the Manager's Menu. 050628 Models C708 & C716 Important: To the Operator...

  • Page 26: Manager's Menu

    RESET DRAW COUNTER displayed. The control keys are functional in the Manager's Menu when the CURRENT SET CLOCK CONDITIONS screen is displayed. (See CURRENT AUTO HEAT TIME CONDITIONS on page 28.) 060413 Important: To the Operator Models C708 & C716...
  • Page 27 DOWN arrow to move the arrow CLOCK option is selected when the machine is not to “Disable”. Then touch the SEL symbol to save the in a brush clean state. new setting. 080222 Models C708 & C716 Important: To the Operator...
  • Page 28 DISABLED placed in the AUTO or STANDBY mode. Enable > Disable Note: This option can only be accessed through the Service Menu for the C708. 080222 Important: To the Operator Models C708 & C716...
  • Page 29 Mix Low and Mix Out will illuminate as the mix level drops in the hopper, but the audible tone COMP ON TOO LONG - The compressor run time will be disabled. exceeded the 11 minute timer. Models C708 & C716 Important: To the Operator...
  • Page 30 POWER SWITCH OFF - The power switch was (L/R) BRL>59F (15C) - The mix temperature in the turned OFF during the heat cycle. hopper exceeded 59°F (15°C). 050628 Important: To the Operator Models C708 & C716...
  • Page 31 HPCO IN HEAT CYCLE COOL = Total time the hopper (h) and barrel (b) A high pressure cut-out condition occurred temperature was above 41°F (5°C) during the COOL during the heat cycle. phase. 050628 Models C708 & C716 Important: To the Operator...
  • Page 32 Menu by touching the SEL symbol. Touch the SEL symbol to advance to the next system information screen containing the software language version. Language V2.00 English 621 > Next 081111 Important: To the Operator Models C708 & C716...

  • Page 33: Operating Procedures

    Section 6 Operating Procedures The C708 stores mix in a hopper and has a 3.4 Step 3 quart (3.2 liter) capacity freezing cylinder with a Heavily lubricate the inside portion of the boot seal and also lubricate the flat end of the boot seal that single spout door.
  • Page 34 Holding the rear blade on the beater, slide it into the freezing cylinder halfway. Install the front scraper blade over the front holding pin. (See Figure 18.) 11249 Figure 20 Repeat these steps for the other side of the Figure 18 Model C716. Operating Procedures Models C708 & C716...

  • Page 35: Freezer Door Assembly

    Freezer Door Assembly Lightly lubricate the inside of the top of the freezer door valve cavity. (See Figure 23.) The assembly of the C708 freezer door is different from the C716 freezer door. Please follow the appropriate instructions for your machine.
  • Page 36 Install the front drip tray and splash shield under the door spout. (See Figure 32.) Figure 26 Note: The C708 features an adjustable draw handle to provide portion control, giving a better consistent quality to your product and controlling costs.
  • Page 37 Lubricate the inside of the freezer door spouts, top rate of 5 to 7-1/2 oz. (142 g. to 213 g.) of product by and bottom. weight per 10 seconds. Models C708 & C716 Operating Procedures...

  • Page 38: Mix Pump Assembly

    Install the front drip tray and splash shield under the Apply a thin layer of lubricant to the inside of the door spouts. (See Figure 32.) pump cylinder at the retaining pin hole end. (See Figure 34.) 15130 Figure 32 Figure 34 Operating Procedures Models C708 & C716...
  • Page 39 Slide the pump valve gasket into the holes on the The adapter must be positioned into the notch cap. DO NOT lubricate the gasket. (See Figure 37.) located at the end of the pump cylinder. Models C708 & C716 Operating Procedures...
  • Page 40 Assemble the feed tube assembly. Slide the check sanitizing. (See Figure 43.) ring into the groove of the feed tube. (See Figure 41.) 12166 15133 Figure 41 Figure 43 Operating Procedures Models C708 & C716...

  • Page 41: Sanitizing

    Repeat these steps for the other side of the mix hopper, the mix inlet hole, the air/mix pump, the Model C716. pump clip, the mix feed tube, and the locking clip. 080617 Models C708 & C716 Operating Procedures...
  • Page 42 USE WARM WATER AND FOLLOW THE MANUFACTURER'S SPECIFICATIONS. Step 7 Note: Be sure your hands are clean and Pour the sanitizing solution into the mix hopper. sanitized before going on in these instructions. 080617 Operating Procedures Models C708 & C716...

  • Page 43: Priming

    Fill the hopper with fresh mix and place the mix Figure 51 hopper cover in position. Repeat these steps for the other side of the Repeat these steps for the other side of the Model C716. Model C716. Models C708 & C716 Operating Procedures...

  • Page 44: Daily Closing Procedures

    Prepare a small amount of an approved 100 PPM cleaning/sanitizing solution (example: Kay-5® or Stera-Sheen®). USE WARM WATER AND FOL- LOW THE MANUFACTURER'S SPECIFICATIONS. Brush clean the agitator(s) and the hopper cover(s). Figure 53 080222 Operating Procedures Models C708 & C716...

  • Page 45: Daily Opening Procedures

    The heating cycle will take a brush clean each item for a total of 60 seconds, maximum of 4 hours to complete with full hoppers. repeatedly dipping the brush in sanitizing solution. 080222 Models C708 & C716 Operating Procedures...

  • Page 46: Manual Brush Cleaning

    (See page 24.) out when the draw valve is opened. Step 2 Note: This procedure should be performed 15 Drain the product from the freezing cylinder and the minutes prior to serving product. mix hopper. Operating Procedures Models C708 & C716...

  • Page 47: Rinsing

    With a mix pail beneath the door spout,(s) open the draw valve and touch the WASH symbol Step 5 (See Figure 59.) Place an empty pail beneath the door spout(s). 080617 Models C708 & C716 Operating Procedures...

  • Page 48: Disassembly

    Remove the pump drive shaft from the drive hub in seal(s), or o-ring(s) should be replaced or properly the rear wall of the mix hopper. (See Figure 60.) lubricated. Operating Procedures Models C708 & C716...

  • Page 49: Brush Cleaning

    Using the black brush, clean the rear shell bearing at the back of the freezing Step 5 cylinder. (See Figure 62.) Wipe all exterior surfaces of the freezer with a clean, sanitized towel. Figure 62 080617 Models C708 & C716 Operating Procedures...

  • Page 50: Important: Operator Checklist

    6. The temperature of the mix in the mix hopper electrical power prior to cleaning the and walk-in cooler should be below 40_F condenser. Failure to follow this instruction (4.4_C). may result in electrocution. 050808 Important: Operator Checklist Models C708 & C716...

  • Page 51: Winter Storage

    Your local Taylor Distributor can perform this winter storage service for you. Wrap detachable parts of the freezer such as beater, blades, drive shaft, and freezer door, and Winter Storage place them in a protected dry place.

  • Page 52: Troubleshooting Guide

    There was a power failure. f. Check fault messages and product temperature. Disassemble and brush clean, or initiate a heat treatment cycle. Important: Operator Checklist Models C708 & C716...
  • Page 53 Call an authorized service - - - technician. is broken. h. Feed tube or check ring h. Make sure feed tube and 36, 39 rubber check ring are not properly installed. properly installed. Models C708 & C716 Important: Operator Checklist...
  • Page 54 12. Excessive mix leakage a. Bottom o-ring on draw a. Lubricate properly or replace the o-ring. from the bottom of door valve is improperly spout. lubricated or worn. Important: Operator Checklist Models C708 & C716...
  • Page 55 10 drawn. seconds. b. Pump assembled b. Assemble and lubricate according to instructions incorrectly. in this manual. c. Freezing cylinder not c. Drain the freezing cylinder and reprime the machine. primed correctly. Models C708 & C716 Important: Operator Checklist...

  • Page 56: Parts Replacement Schedule

    Black Bristle Brush, 1” x 2” Inspect & Replace Minimum if Necessary Double-Ended Brush Inspect & Replace Minimum if Necessary Yellow Bristle Brush Inspect & Replace Minimum if Necessary Brush Set (3) Inspect & Replace Minimum if Necessary Parts Replacement Schedule Models C708 & C716...

  • Page 57: Parts List

    Section 10 Parts List Models C708 & C716 Parts List...
  • Page 58 Parts List Models C708 & C716...
  • Page 59 Models C708 & C716 Parts List...
  • Page 60 Parts List Models C708 & C716...
  • Page 61 Models C708 & C716 Parts List...
  • Page 62 Parts List Models C708 & C716...
  • Page 63 Models C708 & C716 Parts List...
  • Page 64 Parts List Models C708 & C716...
  • Page 65 Models C708 & C716 Parts List...
  • Page 66 Parts List Models C708 & C716...
  • Page 67 Models C708 & C716 Parts List...
  • Page 68 Parts List Models C708 & C716...
  • Page 69 Models C708 & C716 Parts List...
  • Page 70 Parts List Models C708 & C716...
  • Page 71 Model C708 057010-27 Rev. 2/08...
  • Page 72 Model C708 057010-27 Inset Rev. 2/08...
  • Page 73 Model C708 057010-33 Rev. 2/08...
  • Page 74 Model C708 057010-40 Rev. 2/08...
  • Page 75 Model C708 057010-58 Rev. 2/08...
  • Page 76 Model C716 059900-27 Rev. 2/08...
  • Page 77 Model C716 059900-27 Inset Rev. 2/08...
  • Page 78 Model C716 059900-33 Rev. 2/08...
  • Page 79 Model C716 059900-40 Rev. 2/08...
  • Page 80 Model C716 059900-58 Rev. 2/08...

This manual is also suitable for:

C716

Table of Contents