1. Manuals
  2. Brands
  3. TdA Manuals
  4. Gate Opener
  5. ZK300DC
  6. Installation and user manual

TdA ZK300DC Installation And User Manual

Swing gate operator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Swing Gate Operator
ZK300DC
Installation and Users Manual
WARNING
ONLY QUALIFIED AND EXPERIENCED
TECHNICIANS SHOULD ATTEMPT INSTALLATION
OR SERVICE TO THIS UNIT, OTHERWISE, SERIOUS
PERSONAL INJURY, DEATH, OR PROPERTY
DAMAGE MAY OCCUR.
SAVE THESE INSTRUCTIONS.
Total Door Automation (Australia) Pty Ltd
www.totaldoorautomation.com.au
sales@totaldoorautomation.com.au
Technical Support 1800 AUSTDA (1800 287 832)

Advertisement

Table of Contents
loading

Related Manuals for TdA ZK300DC

Summary of Contents for TdA ZK300DC

  • Page 1 Swing Gate Operator ZK300DC Installation and Users Manual WARNING ONLY QUALIFIED AND EXPERIENCED TECHNICIANS SHOULD ATTEMPT INSTALLATION OR SERVICE TO THIS UNIT, OTHERWISE, SERIOUS PERSONAL INJURY, DEATH, OR PROPERTY DAMAGE MAY OCCUR. SAVE THESE INSTRUCTIONS. Total Door Automation (Australia) Pty Ltd www.totaldoorautomation.com.au...

  • Page 2: Table Of Contents

    ZK300DC SWING GATE OPERATOR USER’S MANUAL TABLE OF CONTENTS Important Safety Information Additional Features Packing List Specifications Necessary Tools Site Preparation Mechanical / Installation Electrical / Control Box Mounting Electrical / Main Terminal Wiring Electric Lock  Flashing Light ...

  • Page 3: Important Safety Information

    User programmable and user erasable remote codes.  Remote control hopping code technology prevents your remote code being accessible  to others. For safety protection, ZK300DC will stop if it encounters an obstruction during closing  or opening. Manual key release design for emergency purposes. ...

  • Page 4: Packing List

    3. Packing List After receiving the product, you should make an unpack-inspection, in which you should check whether the product was damaged. If you have any problem please contact dealer. Table 1 Packing List of ZK300DC Swing Gate Operator Quantity Item...

  • Page 5: Specifications

    3.5Ah, 24V 5. Necessary Tools The following tools may be necessary to install the ZK300DC operator. You will need an electric drill, hacksaw, screwdrivers, tape measure, multimeter, level, wire cutters and wire stripper, a socket set, and possibly access to a welder if your installation cannot use the supplied brackets.

  • Page 6: Mechanical / Installation

    ZK300DC SWING GATE OPERATOR USER’S MANUAL Use another cable for safety devices (such as electric lock, infrared photocell, flashing  light, external button switch etc.), electrical lock wire should be more than 1.5mm and the other wires should be more than 0.5 mm To prevent rainwater from entering into the cable, arrange the cable as show in Fig.1.
  • Page 7 ZK300DC SWING GATE OPERATOR USER’S MANUAL To release the operator by turning the release nut anticlockwise. The gate is mounted on one face of the mounting post, and the operator is mounted on the face 90 degrees from it. Below is schematic of push to open configurations.
  • Page 8 ZK300DC SWING GATE OPERATOR USER’S MANUAL Fig.5 Rear parts of gate operator Fix the post bracket on the cement pillar with screws and spacers (or welding for  metal pillar). Make sure that the bracket is plumb and lever. Mount the rear part of the gate operator on the post bracket using the pin supplied, ...
  • Page 9 ZK300DC SWING GATE OPERATOR USER’S MANUAL Fig.7 Front parts of gate operator Move the front part of gate operator up and down slowly, check the installation height  of the gate bracket, fit the gate bracket to the gate, and use a level meter to check the flatness of the operator (See Fig.9).
  • Page 10 ZK300DC SWING GATE OPERATOR USER’S MANUAL Fig.8 Level Fig.9 Release function After installing the brackets, loose the release nut by turning the key about 5 circles anticlockwise, make sure that the release nut can not be pulled out. Manually open or close the gate, review bracket positioning and that its dimensions conform to those listed in the specifications of this document.
  • Page 11 ZK300DC SWING GATE OPERATOR USER’S MANUAL Stop block –open position After the gate reaches the desired angle (90°or 105°), ensure 5-10mm space exists  between the gate and stop block See Fig.4. This margin is required to prevent the gate from bumping on the stop block.

  • Page 12: Electrical / Control Box Mounting

    ZK300DC SWING GATE OPERATOR USER’S MANUAL Primary Secondary A- Top view Gate Release here Steel plate Electric lock Base plate B- Side view Fig.11 8. Electrical / Control Box Mounting Install the control box Make sure that power is OFF before making any electrical connections.

  • Page 13: Electrical / Main Terminal Wiring

    ZK300DC SWING GATE OPERATOR USER’S MANUAL Fig.12 9. Electrical / Main Terminal Wiring Connect the operator to the control box as shown in Fig.14. Connect primary motor that on the primary gate (with electric lock) to MOTOR A, connect the secondary gate to MOTOR B. (See Fig.14)

  • Page 14: Electric Lock

    Attach two wires of flashing light to port ‘Alarm lamp’. Install the external button switch (Normally open) The ZK300DC is equipped with an interface for an external button switch or keypad. To install the keypad attach two wires of your keypad to the port ‘Open/ Close/ Stop’.

  • Page 15: Electrical / Setting

    ‘Ⅱ’ is indicated on the LED display, the interval time between two gates is 2 seconds. Setting obstruction force (level1- level20 adjustable) ZK300DC will stop if it encounters an obstruction during closing or opening.  Press and hold K3 button for more than 4 seconds, until the number ’-’ is displayed ...

  • Page 16: Maintenance

    ZK300DC SWING GATE OPERATOR USER’S MANUAL 11. Maintenance Regularly verify that the gate swings freely.  Make sure the hinges function perfectly.  Verify correct operation of the safety devices.  Keep operator clean at all times.  12. Troubleshooting...

Table of Contents