Page 1
AUTOMATIC BOOM GATE USER’S MANUAL MODEL DC535Y/DCZ535Y DC655Y/DCZ655Y WARNING! ONLY QUALIFIED AND EXPERIENCED TECHNICIANS SHOULD ATTEMPT INSTALLATION OR SERVICE TO THIS UNIT, OTHERWISE, SERIOUS PERSONAL INJURY, DEATH, OR PROPERTY DAMAGE MAY OCCUR. PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER REFERENCE. Total Door Automation (Australia) Pty Ltd www.totaldoorautomation.com.au...
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL 1. Important safety information Carefully read and follow all safety precaution and warnings before attempting to install and use DC660-3(L, M, R) boom gate. Incorrect installation can lead to severe injury. ⚫ The automatic boom gate should be installed by a qualified technician; otherwise, serious personal injury or property damage may occur.
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL 4. Installation Necessary Tools The following tools may be necessary to install the automatic boom gate. You will need standard screwdrivers, an electric drill and spanners. The entire configuration and dimension are shown in the diagram below.
Page 5
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL Right-hand boom gate (DC535Y, DC655Y) and left-hand boom gate (DCZ535Y, DCZ655Y) DC535Y, DC655Y DCZ535Y, DCZ655Y Fig.2 Conduit Make one input hole for electric wires. In order to protect the wires, conduits must be set into the concrete when it is poured.
Page 6
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL Fig.4 Boom gate (see Fig.5) Place the boom gate back into position, mount the boom gate to the concrete pad with washers and nuts. Fig.5 Bar (see Fig.6) Mount the bar to the assembled cubicle and lock it with the four M10×16 socket head screws.
Page 7
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL ⚫ Turn the crank clockwise or counterclockwise. ⚫ Withdraw the crank before switching the power back on. Fig.6 Limit switch (N.O.) see Fig.7 ⚫ The adjustable limit switches are used to stop the bar in the opened and closed positions.
Page 8
Four holes (ø15) on the driven lever. The boom gate is normally delivered in the first hole ( DC655Y/DCZ655Y: suitable for bar length from 5m~6m) or the second hole ( DC535Y/DCZ535Y : suitable for bar length from 4.5m~5m). If you need to change it to the third (3.5m~4.5m) or the fourth (3m~3.5m) hole proceed as follows:...
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL 5. Electrical Remote control Button 1 Button 3 Button 2 Button 4 Fig.9 ⚫ To add extra remote controls (Learning): Press the button ‘AN’ (see Fig.10 control board scheme No.13) on the control board, a beeper will be heard, then press the remote control button which you want to use, the beeper will ring again, press the same remote control button again, the beeper will ring at 1/2Hz frequency and then stop, the last ring is continuous.
Page 10
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL (the range is 0~44 sec.), this period of time is regarded as ‘auto-close time’. close the bar by pressing the same button, after the bar stops at the horizontal position, return DIP-switch 3 to OFF position.
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL 15. Transformer: 220V/12Vx2 16. Sampling Transformer: 110V/ 8.8V 4W 17. Alarm Lamp: AC220V 18. Motor Capacitor: 10μF 450V AC 19. Motor: U (Com), V (Positive direction), W (Opposite Direction), E (Earth) 20. Power Input: E (Earth), L (Live), N (Neutral) AC240V 6.
DC535Y/DCZ535Y, DC655Y/DCZ655Y BOOM GATE USER’S MANUAL 8. Packing list Make sure that all parts are included before using. Refer to packing list. If any parts appear to be missing, contact a dealer. Item Quantity Assembled cubicle Bar locking bracket Bar cover...