Advertisement
Quick Links
KIT COMPONENTS
• A) Radio trim panel • B) Radio housing • C) Radio brackets • D) (4) #8 x 3/8" Phillips screws • E) (4) Panel clips
A
B
Metra. The World's Best Kits.
®
Chevrolet Trax 2017-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
KIT FEATURES
• ISO DDIN radio provision
• Painted high gloss black
C
D
MetraOnline.com
E
© COPYRIGHT 2019 METRA ELECTRONICS CORPORATION
95-3023HG
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Preparation . ......................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: TBA
Antenna Adapter: 40-EU55
Steering Wheel Control Interface: ASWC-1
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32" Socket wrench • Cutting tool
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 8/13/19 INST95-3023HG
Advertisement
Related Manuals for Metra Electronics 95-3023HG
Summary of Contents for Metra Electronics 95-3023HG
- Page 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 8/13/19 INST95-3023HG...
- Page 2 DASH DISASSEMBLY KIT PREPARATION 1. Unclip and remove the dash panel Attention! After the sub-dash has been cut, surrounding the radio. (Figure A) the factory radio will no longer be able to be installed. 2. Unclip and remove the radio trim. 1. Cut the sub-dash to allow room for the (Figure B) aftermarket radio. (Figure A) 3. Remove (2) 9/32” screws securing Remove 2. Attach (4) panel clips provided with the the radio, then pull down and back to shaded areas kit onto the radio trim panel. (Figure B) release the radio. Unplug the connectors (Figure B) to remove the radio. (Figure C) Continue to Kit Assembly 4. Unclip and slide off the plastic trim piece on the top of the radio. (Figure D) (Figure A) 5. Remove (2) 9/32” screws securing each a/c vent, then unclip and remove the vents. “Head On” View Continue to Kit Preparation (Figure C) (Figure A) (Figure B)
- Page 3 2. Secure the radio assembly to the radio a. Slide the radio assembly into housing using the (4) #8 x 3/8” Phillips the dash. screws provided. (Figure B) b. Wiggle the a/c vents in. 3. Attach the plastic trim piece removed in c. Secure the now complete assembly dash disassembly to the top of the to the dash using the (6) factory radio housing. 9/32” screws. 4. Locate the factory wiring harness and 6. Reassemble the dash in reverse (Figure A) (Figure B) antenna connector in the dash and order of disassembly to complete the complete all necessary connections to installation, using the 95-3023HG radio the radio. Metra recommends using trim panel. the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation. REV. 8/13/2019 INST95-3023HG...
- Page 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 8/13/19 INST95-3023HG...