Page 1
-5dB -10dB -20dB SIGNAL PROFESSIONAL POWER AMPLIFIER This booklet contains important information concerning the proper and safe operation of your new amplifier. XT-Series XT-500 / XT-600 / XT-900 / XT-1250 Made in Taiwan Index 03 Introduction 04 Front Panel 05 Rear Panel...
Page 2
IMPORTANT SAFETY INSTRUCTIONS XT-500 / XT-600 / XT-900 / XT-1250 This symbol is intended to alert the user to the presence of This symbol is intended to alert the user of non insulated "dangerous voltage" within the product's the presence of important operating and CAUTION enclosure that may be of sufficient magnitude to constitute maintenance (servicing) instructions in the...
Congratulations and thank you for purchasing an XT Series amplifier. This moisture. amplifier is a representation of UNiKA’s continuing commitment to produce Do not spill water or other liquids into or on to your unit. the best and highest quality audio products at an affordable price. These amplifiers are designed to provide a big impact in sound reproduction.
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Set Up Safety Precautions | Introduction | Front Panel | Rear Panel | Speakon Assembly | Operating Modes | Protection | Amplifier Features | Specifications SET UP INPUTS The XT Series amplifier allows you to use XLR 3-pin input connector per channel. A XLR female jack for...
Page 9
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Set Up Safety Precautions | Introduction | Front Panel | Rear Panel | Speakon Assembly | Operating Modes | Protection | Amplifier Features | Specifications Bare Wire Connections: ( Figure 1/5" When connecting your speakers to the amplifier using bare wire, unscrew the red and black caps on 13mm the binding post, be sure not to completely remove or unscrew the red and black caps.
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Speakon Assembly Safety Precautions | Introduction | Front Panel | Rear Panel Set Up | Operating Modes | Protection | Amplifier Features | Specifications Speakon Assembly: You will need a pair of Neutrik speakon NL4FC connectors. You will also need high- quality two or four conductor speakon cable, a pair of needle-nosed pliers and a 1.5-mm...
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Operating Modes Safety Precautions | Introduction | Front Panel | Rear Panel Set Up Speakon Assembly | Protection | Amplifier Features | Specifications Operating Modes STEREO OPERATION : Page 10/ Figure 12 & 13 detail examples of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier.
Page 12
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Operating Modes Safety Precautions | Introduction | Front Panel | Rear Panel Set Up Speakon Assembly | Protection | Amplifier Features | Specifications Operating Modes MONO BRIDGE OPERATION : Page Figure 4 & 15 detail mono bridge set-up. Be sure your amplifier and all other audio equipment are powered down.
Page 13
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Operating Modes Safety Precautions | Introduction | Front Panel | Rear Panel Set Up Speakon Assembly | Protection | Amplifier Features | Specifications Operating Modes PARALLEL MONO: Parallel ties the two channel line inputs together so that they will both be driven by the same signal, without the need for external jumpers or wiring.
Page 14
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Operating Modes Safety Precautions | Introduction | Front Panel | Rear Panel Set Up Speakon Assembly | Protection | Amplifier Features | Specifications SUBWOOFER MODE : This mode sends low frequencies to your speakers without the use of an external cross-over. The subwoofer operation can be operated in stereo, parallel, or bridge mono modes.
Page 15
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Operating Modes Safety Precautions | Introduction | Front Panel | Rear Panel Set Up Speakon Assembly | Protection | Amplifier Features | Specifications CH-2 Input CH-1 Input STEREO BRIDGE PARALLEL Set to...
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Protection Safety Precautions | Introduction | Front Panel | Rear Panel Set Up Speakon Assembly Operating Modes | Amplifier Features | Specifications PROTECTION LIMITER - The XT Series comes with a built in limiter. When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this time, the volume should be lowered to reduce distortion.
UNiKA XT-500 / XT-600 / XT-900 / XT-1250 Protection Amplifier Features Safety Precautions | Introduction | Front Panel | Rear Panel Set Up Speakon Assembly Operating Modes | Specifications Operating Voltage (AC Mains) - On the rear panel will indicate the correct AC mains voltage. Connecting to the wrong voltage is dangerous and may damage the amplifier.