Table of Contents
Advertisement
S
ERIES
S e r i e s
RODEO
S é r i e
B a u r e i h e
S e r i e
AUTOMATION SYSTEM FOR SLIDING DOORS,
WITH MICROPROCESSOR CONTROL
for door wings weighting
up to
A
UTOMATION SYSTEM FOR SLIDING
FM-S
YSTEM
S
ISTEMA
RADIOMANDOS
125
kg each
Documentazione
M71
119PM71
DOORSUERUNGEN
FM
Tecnica
3.0
rev.
01/2000
©
CAME
CANCELLI
AUTOMATICI
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CAME RODEO Series
Summary of Contents for CAME RODEO Series
- Page 1 S e r i e s RODEO S é r i e B a u r e i h e rev. 01/2000 S e r i e © CAME CANCELLI AUTOMATICI 119PM71 UTOMATION SYSTEM FOR SLIDING DOORSUERUNGEN FM-S YSTEM ISTEMA...
- Page 2 Kg per door. - MR8334-70-90 Activ infrared safety sensor; - MP8030/8060 Pressure-sensitive. For easy installation and maintenance, be sure to use CAME original control equipment, safety systems and accessories. . c . o i t . c . < °...
- Page 3 RODEO SERIE SECTION-COVERING BOXES DIMENSIONS Drilling for fixing the section 250 x n° step Right side/internal view point of departure of the step drilling T = Length of the beam BEAM WITH SECTION- Sez. A-A COVERING BOX SERIES 001LC00 AND LTC STOPPERS 29±6 BEAM WITH...
- Page 4 RODEO SERIE DIAGRAMS OF GLASS DOOR WINGS Y = height at which beam is mounted = H + 18 mm SUPPORT PROFILE H = working height of passage V = height of glass door ATTACH SECTION CRYSTAL 29±6 SOLUTION FOR GLASS SOLUTION FOR GLASS DOOR WING WHIT DOOR WING WITHOUT...
- Page 5 RODEO SERIE DIAGRAMS OF GLASS DOOR WINGS GLASS DOOR WING(S) WITH LOWER SKIRT MA 7070 (L= 1400 mm) MA 7170 (L= 2000 mm) MA 7053 (L= 1400 mm) MA 7153 (L= 2000 mm) DRILL POINTS FOR INSTALLING THE UPPER GLASS PANEL AND BEAMBEAM L wing ø...
- Page 6 RODEO SERIE DIAGRAMS OF DOOR WINGS WITH FRAME Y = height at which beam is mounted = H + 18 mm H = working height of passage I = height of door wing with frame ATTACH SECTION FRAMED 29±6 SOLUTION FOR SOLUTION FOR FRAMED DOOR WING SOLUTION FOR...
- Page 7 RODEO SERIE DIAGRAMS OF DOOR WINGS WITH FRAME DOOR WING(S) WITH FRAME, WITHOUT LOWER GUIDE PROFILE MA 7071 (L= 1400 mm) MA 7171 (L= 2000 mm) DOOR WING(S) WITH FRAME, WITH LOWER GUIDE PROFILE MA 7071 (L= 1400 mm) MA 7171 (L= 2000 mm) MA 7051 (L= 1400 mm) MA 7151 (L= 2000 mm)
- Page 8 RODEO SERIE INSTALLING THE BEAM 1) Remove the profile housing (optional at extra cost), if present 2) Remove the trolleys from the support profile by proceeding as follows: TROLLEY WITH LOWER 2 a) Loosen the mounting ATTACHMENT SYSTEM screws to disconnect the FOR BELT trolleys (which are engaged by the belt) from the connecting...
- Page 9 RODEO SERIE INSTALLING THE DOOR WINGS 1) Fasten the trolleys to the door wings by proceeding as follows: WITH ELECTRIC LOCK which opens toward which opens toward model RODEO 1 (single door wing) LEFT RIGHT model RODEO 2 (double door wing) 2) Raise the door wings and WITH CONTACT FREE...
- Page 10 RODEO SERIE MECHANICAL ADJUSTMENTS The trolleys can be used to adjust the alignment of the door wings as follows: - vertical adjustment R , with bolts and nuts A and B - transverse adjustment R , with bolts and nuts C - horizontal adjustment R , with bolts and nuts D and E...
- Page 11 RODEO SERIE MECHANICAL ADJUSTMENTS VERTICAL ADJUSTMENT R To obtain correct vertical alignment of the door wings, adjust the trolleys as follows : - Loosen screws A. - Turn vertical adjustment screw B until the door wing(s) is/ are as perpendicular to the ground as possible. If the automation system is being used to power two sliding door wings, adjust this screw so that no gap is left between the door wings when they are closed.
- Page 12 RODEO SERIE MECHANICAL ADJUSTMENTS ADJUSTING THE BELT TENSION If necessary, the idle pulley can be used to adjust the tension on the belt. Proceed as follows: 1) Loosen the mounting screws on the pulley. 2)Rotate the adjustment screw until the correct belt tension is obtained.
- Page 13 RODEO SERIE MECHANICAL ADJUSTMENTS BELT SUPPORT The belt support is used to control belt vibration. It is installed at the centre of automation systems powering two door wings whose support profile exceeds 3020 mm in length. If necessary, the support may be bent into the required shape. N.B.
- Page 14 RODEO SERIE ZP8 ELECTRICAL CABINET CONNECTION FOR ELECTRIC LOCK TERMINAL BOARD FOR CONNECTION OF CONNECTION FOR FUNCTION SWITCH MA7012 MOTOR ENCODER BATTERY POWER MA7041 SUPPLY " " CONNECTION FOR COMPASS INDICATOR LEDS OPERATING SYSTEM 1.6A RAPID BLOW FUSE ON RESET KEY ACCESSORIES 1 2 3 4 5 6 7 8 FUSIBILE...
- Page 15 RODEO SERIE ZP8 ELECTRICAL CABINET 6 7 8 RESET The RESET key, resets the data and restarts the automation in question. MA7032 The APRE key, starts automation and completes an opening cycle. Attention: The function of the open key is excluded if dip switch 5 APRE (10-way module) is set to ON.
- Page 16 RODEO SERIE SELECTION FUNCTIONS b i l o i t t i h o i t « . » e l i S " " p o i t h t i o i t i " l a t n i l t n i "...
- Page 17 RODEO SERIE STARTING UP THE SYSTEM VERIFICHE PRELIMINARI Before start-up, make sure that: The electric lock (if installed) has been manually released; The proper tension has been applied to the belt (see p. 12); The checks described on p. 13 (checking for proper assembly) have been performed; No objects are present along the path taken by the door wings as they move;...
- Page 18 RODEO SERIE INSTALLATION OF ACCESSORIES (available upon request) MA7032 - Battery-powered emergency system This emergency system opens the door in case of power failure. It includes a pair of 12V (1.2Ah) batteries as well as a circuit card that keeps the batteries charged and distributes power to the automation system. By using dip switches 9 and 10 (10-way module), the emergency system can be programmed to operate in the following ways when the power fails: Note: When functioning is interlocked (see p.
- Page 19 RODEO SERIE INSTALLATION OF ACCESSORIES (available upon request) MA7012 - Electric lock Electro-mechanical system for locking the door wings, with gravity-powered mechanical locking action and electric unlocking system. This device locks the door wing(s) in the closed position (and/or in the open position) by engaging a bracket installed on one of the trolleys.
- Page 20 RODEO SERIE INTERFACE FUNCTION DIAGRAM OF TWO INTERLOCKED AUTOMATION 1 or 2 copies of photoelectric cells Electric lock MA7012 Board (MA9011-MA9111) Radar (MR8002-MR8101) Anti-panic board MA7032 Function selector MA7041 EXTERNAL AUTOMATION (MASTER) B A T T . 2 4 A C 2 4 A C B A T T .
- Page 21 RODEO SERIE Connections required Connect the accessories to the two panels and to each other using the compass clamp (bussola) according to the illustrated diagram. Set dip switch 6 on the outer automation system to ON, which will assign MASTER control status to that system. All control sensors and function switch MA7041 (if installed) must be connected to the MASTER automation system, which controls the other automation system.
- Page 22 RODEO SERIE CONNECTION OF ACCESSORIES TO THE PANEL FOREWORD To facilitate the wiring procedure, the entire length of the beam is equipped with a space for lodging and distributing the cables. Two no.2 (common) terminals have been provided on the terminal board for connection of accessories. The power cables should be arranged on the left side of the beam, where the transformer is located.
- Page 23 RODEO SERIE ACCESSORIES SAFETY CONTROL MF 9011 Pair of photocells with range of 7m. MA 7041 Function switch MF 9111 Double pair of photocells MR 8001 Narrow-field radar with range of 7 m. MR 8002 Wide-field radar MA 7012 Electric lock, complete with release MP 8030 Sensitive platform, 800 mm x 300 mm cord.
Need help?
Do you have a question about the RODEO Series and is the answer not in the manual?
Questions and answers