1. Manuals
  2. Brands
  3. Konica Minolta Manuals
  4. All in One Printer
  5. bizhub C754
  6. Installation manual

Konica Minolta bizhub C754 Installation Manual

Hide thumbs Also See for bizhub C754:
Table of Contents

Advertisement

Quick Links

Download this manual
<Important>
Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.
I. Outline of installation procedures
*2
WT-506
AU-201
AU-102
WT-509
PK-521
SD-512
When installing the machine and associated options
as a system, follow the order shown on the upper.
Note:
• For the detailed installation procedures for each
option, follow the instructions given in the corre-
sponding installation manual and perform the
procedures correctly.
• Once the Power Switch is turned ON, do not
turn OFF it until the installation work has been
completed.
• When transporting the machine, assign an ade-
quate number of persons to the job and follow
the specified correct procedures.
(mass: approx. 221 kg (487-3/16 lb))
INSTALLATION MANUAL
Machine
SP-501
MK-715
*4
HT-508
Electronic system options
MK-735
*1
AU-201
KH-102
ZU-606
OT-503
JS-602
FS-535
PI-505
/
Applied Machines:
LU-204
LU-301
PK-520
FS-534
SD-511
*1
: When installing the AU-201 with MK-735
*2
: When installing the AU-201 without MK-735
*3
: No particular order in installation procedures
*4
: Varies depending on the applicable marketing area
E-1
✱ Electronic system options
*3
EK-604
EK-605
*3
UK-204
*3
SC-508
*3
FK-511
*3
VI-506
*3
IC-414
A2X0-9951-01
/
*3
A2X0IXC001DA

Advertisement

Table of Contents
loading

Related Manuals for Konica Minolta bizhub C754

Summary of Contents for Konica Minolta bizhub C754

  • Page 1 INSTALLATION MANUAL Applied Machines: <Important> Be sure to correctly follow the procedures in order as explained in this Installation Manual. If you do not follow the procedure in order, the image trouble may occur. I. Outline of installation procedures ✱ Electronic system options WT-506 LU-204 AU-201...
  • Page 2 II. Installation space (unit: mm (inch)) III. Pre-installation check items bizhub C754 + ZU-606 + FS-535 + LU-204 1. Select a level and stable place for installing the machine. 2. Be sure to use a power source of the voltage and 2556 (100-5/8) frequency indicated in the product specifications.

  • Page 3: Unpacking The Machine

    V. Accessory parts VI. Unpacking the machine Whether the slope is supplied with this machine or Name Q’ty not depends on your marketing areas. Follow the 1. User’s guide holder notes below. 2. Quick start guide Note: 3. Quick assist guide •...
  • Page 4 3. Hold onto the handle of the machine and tilt the 6. Position the slope as illustrated and drive nails in machine to the right and left. Under this condition, to fix the slope in position. remove the fixing materials (lower). Caution: Insert the nails in the outer holes.
  • Page 5 <B. When using the jig slope> 3. Hold onto the handle of the machine and tilt the machine to the right and left. Under this condition, remove the fixing materials (lower). 1. Open the shipping box and remove the packag- ing materials.

  • Page 6: Removing Protective Tape, Packing And Other Shipping Materials

    VII. Removing protective tape, packing 5. Holding onto the front cover and the back panel of the machine, slide the machine down along the and other shipping materials slope. Caution: 1. Remove the protective tape and protective mate- rials. Machine mass: 221 kg (487-3/16 lb) •...
  • Page 7 2. Remove the reinforcement plate. (Four screws) 5. Pull the tray 1 out and remove the protective tape from the tray. A2X0IXC012DB A2X0IXC015DA 3. Remove the locking screws. 6. Pull the tray 2 out and remove the protective tape from the tray. A2X0IXC013DA 4.

  • Page 8: Installing The Toner Cartridges

    VIII. Installing the toner cartridges 8. Remove the protective tape from trays 3 and 4. Note: Since no toner cartridges are supplied with the machine, purchase a toner cartridge (of different colors) separately. 1. Open the upper front door. A0P0IXC023DB 9.

  • Page 9: Mounting The Accessory Parts

    4. Insert the toner cartridge into the machine. 2. Install the supplied scanner cover. (One supplied mounting screw) Note: Make sure that the color is same between insert- ing port and the toner cartridge. A2X0IXC020DA 3. Attach the supplied connector cover. A2X0IXC060DA 5.

  • Page 10: Installing The User's Guide Holder

    XI. Installing the user’s guide holder 5. Remove the protective cover from the supplied stylus pen. Install the user’s guide holder. Note: Discard the removed protective cover. A2X0IXC024DA A2X0IXC068DA XII. Installing the set guide for banner 6. Set the stylus pen in the place shown in the illus- tration.
  • Page 11 2. Plug the power cord into the power outlet. 2. Slide the touch panel. C4004U139CA A2X0IXC063DA 3. To remove moisture from the paper in the tray, 3. Remove the small cover from the back of the turn ON the switch shown in the illustration. operation panel.

  • Page 12: Toner Supply

    XV. Toner supply <If A3 or Ledger paper is set in step 1> × 6. Touch “Print”, select “A3 ”, and Turn ON the Main Power Switch. press the start key. Note: A test pattern will then be produced on the A3 •...
  • Page 13 × 12. Touch “Copy”, select “A3 ”, and <If A4 or Letter paper is set in step 1> press the start key. ½×11 6. Touch “Print”, select “A4 ”, and A test pattern will then be produced on the press the start key. or Ledger paper.

  • Page 14: Adjusting The Height

    XVIII. Adjusting the height ½×11 12. Touch “Copy”, select “A4 ”, and press the start key. 1. Check the clearance between the upper face of A test pattern will then be produced on the two scanner and the protrusion on the reverse auto- or Letter papers.
  • Page 15 XIX. Adjusting leading edge skew (front 2. Adjust the height by turning the adjustment screw on the right side viewed from the back. side) Clockwise: The rear side will move up. Counterclockwise: The rear side will move down. Note: • If further adjustment is required, adjust the height Perform this adjustment if necessary.
  • Page 16 6. Obtain the difference between the deviation of 9. When the difference of the deviation is - (minus), the chart and the deviation of the sample. turn the adjustment screw located at the back of Difference of the deviation = Y - X the reverse automatic document feeder clockwise Specifications: 0 ±...
  • Page 17 XX. Adjusting leading edge skew (back 5. Open the reverse automatic document feeder and remove the two screws shown in the illustra- side) tion. Note: Perform this adjustment if necessary. 1. Place the chart in the document feeding tray. (Make sure that the blank surface of the chart faces up.) A2X0IXC039DA 6.

  • Page 18: Magnification Adjustment

    XXI. Magnification adjustment 9. Turn the adjustment dial according to the differ- ence of the deviation. <Magnification in the feeding direction> When the difference is a positive (+) value, turn Note: the dial clockwise Perform this adjustment if necessary. When the difference is a negative (-) value, turn the dial counterclockwise 1.
  • Page 19 9. Touch “END.” 16. Display the Service Mode screen. 10. Touch “Exit” on the Service Mode screen. (For details of how to display the Service Mode 11. Turn OFF and ON the Main Power Switch. screen, see the service manual.) 17.

  • Page 20: Mixed Original Size Adjustment

    XXII. Mixed original size adjustment 27. Check whether the difference in the width D between the chart and the copy sample is within Note: the specified range. Perform this adjustment if necessary. Difference in the width D = D of the copy sample –...
  • Page 21 XXIII. Adjusting the document stop posi- 5. Check whether the difference in the width B between the chart and the copy sample is within tion the specified range. Difference in the width B = B of the copy sample – <Sub Scanning Direction 1-side/ Sub Scanning B of the chart Direction 2-side>...
  • Page 22 <Main Scanning (Front)/ Main Scanning (Back)> 19. Check whether the difference in the width A between the chart and the copy sample is within Note: the specified range. Perform this adjustment if necessary. Difference in the width A = A of the copy sample 15.

  • Page 23: Date/Time Setting

    XXIV. Performing Non-Image Area Erase XXV. Date/Time setting Check 1. Display the Service Mode screen. (For details of how to display the Service Mode Note: screen, see the service manual.) Perform the below at the site where customer 2. Display the Date & Time Setting screen. uses the machine.

  • Page 24: Serial Number Input

    XXVII. Serial number input XXX. Changing paper size (Tray 3 and 4) 1. Turn OFF the Main Power Switch. Note: 2. Pull out the tray 3. Serial number input is needed only for optional 3. Remove the front and rear paper guide plates. devices that will be installed later.
  • Page 25 XXXI. Affixing the tray labels/paper size 5. Align the paper guide plate (rear) with the line marked in the bottom of the tray. Secure the labels paper guide plate. (Four screws) Note: Affix the tray labels or paper size labels at the loca- tions shown in the illustration.
  • Page 26 XXXIII. Check through test print XXXV. Network setting Make operation checks using “Setting Information Make the TCP/IP address setting for the network. Print.” Note: 1. Select the function to be used as follows: Consult the network administrator for the setting Menu →...

  • Page 27: Accessory Parts

    SP-501 Stamp Unit INSTALLATION MANUAL I. Accessory parts II. Installation procedures 1. Turn off the machine and unplug the power cord Name Shape Q’ty from the power outlet. 1. Stamp unit 2. Open the left cover of the reverse automatic doc- ument feeder.
  • Page 28 6. Remove the screw shown on the illustration. 11. Mount the plate cover that has been removed in step 5. (Two screws) 12. Mount the mounting plate removed in step 3. (One screw) 13. Set the document feeding tray down. 14.

This manual is also suitable for:

Bizhub c764

Table of Contents