Advertisement
Quick Links
Order No. 9545
BUILDING INSTRUCTIONS
LEKI EXTRA 330SC
For electric power system and 3 x 2200 mAh LiPo cells
This model requires an HoTT radio control system
with at least four functions
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
Modifications reserved! No liability for printing errors. Id.-No. 0062205
06/2011
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for GRAUPNER 9545
Summary of Contents for GRAUPNER 9545
- Page 1 For electric power system and 3 x 2200 mAh LiPo cells This model requires an HoTT radio control system with at least four functions GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205 06/2011...
- Page 2 For this reason we recommend that you wear protective goggles when using this material. Store the adhesive out of the reach of children. Do not use GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205...
- Page 3 “dry” (without glue) first. Good ventilation is essential for this stage; work outdoors if you are not sure. Ensure that glue is applied to all the contact surfaces. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205...
- Page 4 Set the servo to neutral (centre) from the transmitter, and fit the cut-down output arm (included with the DES 476 BB) as shown. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205...
- Page 5 (48) using cyano. Pull hard on both ends of the new pushrod to ensure that the glued joints are secure. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205...
- Page 6 (30) onto the steering arm, glue the lug in the slot in the rudder, then glue the tailwheel bracket (29) to the fuselage. Do not use activator spray for this. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205...
- Page 7 (38) to the wire undercarriage unit (27), then slip the collet supports (37) onto the axles and glue them in place. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205...
- Page 8 (43) to the wing to complete this aspect of construction. Offer up the wing to the fuselage and temporarily fit the retaining screw (44). GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205...
- Page 9 When you are satisfied, install the spinner and propeller as described earlier. Decals If you decide to use the GRAUPNER decals, there is no need to paint the SOLIDPOR® components. If you opt for the LEKI decal version, you should first paint the model overall using GRAUPNER LEXACOLOR spray paint, Order No.
- Page 10 Always land the model flying directly into wind, with the motor idling but not switched off. Flare out just before touch-down with careful use of up-elevator. Here at GRAUPNER Modellbau we hope you have many enjoyable flights with your LEKI EXTRA 330SC...
- Page 11 Ready made Outboard spat shell 1 pair SOLIDPOR® Ready made Wing SOLIDPOR® Ready made Wing spar CFRP 10 / 9 Ø x 800 GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205 06/2011...
- Page 12 Order No. 7748 Spinner cap Order No. 6040.2 Propeller Order No. 1326.12x6 The illustration shows the position of the decals for the LEKI version. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205 06/2011...
- Page 13 You will find more information on this subject in the operating instructions supplied with your radio control system. Be sure to use only those parts included in the kit, together with other genuine Graupner ac- cessories and replacement parts as recommended expressly by us. Even if you change a single component you can no longer be sure that the system will work reliably, and such changes also invalidate your guarantee.
- Page 14 The opposite applies at the end of a flight: always switch the receiving system off first, and finally the transmitter. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205 06/2011...
- Page 15 If material defects or manufacturing faults should arise in a product distributed by us in the Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, Graupner GmbH & Co. KG, D-73230 Kirchheim/Teck, Germany, acknowledge the obligation to correct those defects within the limitations described below.
- Page 16 If you don’t know the location of your nearest disposal centre, please enquire at your local council office. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved! No liability for printing errors. Id.-No. 0062205 06/2011...
Need help?
Do you have a question about the 9545 and is the answer not in the manual?
Questions and answers