Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GRAUPNER X44
Summary of Contents for GRAUPNER X44
- Page 1 Manual VTOL electric model plane with 4 Brushless motors 9944.100...
- Page 2 2 - 16 9944.RTF_jh_V1...
-
Page 3: Table Of Contents
Content table Introduction ................4 Service centre ................ 4 Intended use ................ 5 Package content ..............5 Symbol description ..............6 Safety notes ................6 Required tools and adhesives (not included) ......8 Suggested accessories (not included) ........8 The model assembly .............. 8 Charging LiPo batteries ............ -
Page 4: Introduction
first of all to control safely your model. If you experience any trouble during operation, take the instruc- tions to help or ask your dealer or Graupner Service Centre. Due to technical changes, the information may be changed in this manual without prior notice. Be always updated by checking periodically for news on our website, www. -
Page 5: Intended Use
Intended use The X44 is an almost ready to fly, remote-controlled airplane model. More punctual information about X44 can be found in the Technical data section. The X44 is designed exclusively to be used as a battery-powered, radio controlled model, any other use is not allowed. -
Page 6: Symbol Description
Symbol description Always follow the information marked with the CAUTION or WARN- ING symbol. The signal word WARNING indicates the potential for serious injury, the signal word CAUTION indicates potential minor injuries. The NOTE indicates important information that should alert you to potential property damage. - Page 7 Controls before the start Before each use, check proper function. For this purpose switch on the transmitter and the receiving system. Check that all controls are in neutral position, function properly and turn down the correct side. When flying a model aircraft for the first time, it is advanta- geous if an experienced helper stands aside in the review and the first flights.
-
Page 8: Required Tools And Adhesives (Not Included)
Required tools and adhesives (not included) Allen key 1,5 mm Superglue * No.5821 Activator for instant adhesives * No.953.150 Phillips screwdriver *. * These items are required for any repairs. Suggested accessories (not included) mz-12 HoTT No. S1002.DE LiPo charger ULTRAMAT 14 plus No. -
Page 9: Installing The Lipo Battery
XT-60 connector of the battery is connected. Always mount propellers only after a complete general check. The X 44 FLIGHT CONTROL FLIGHT CONTROL X44 connection cables (left). The optional receiver will be placed near it (right). The outputs have to be connected in the following order: 1. -
Page 10: Installing The Propellers
The Flight Control is a highly complex electronic unit, that aero- dynamically stabilizes the model over several gyros. Both aileron / elevator of the rear wing and the speed control of each brush- less motor are controlled by this unit. NOTE Note that the model has to be hold after connecting the XT-60 connector in a stable position on a flat surface until the gyros of... - Page 11 Arrangement of the propellers (A = clockwise rotation) and (B = coun- ter-clockwise rotation) Propellers rotation sense 1 = Clockwise motor 2 = Counter-clockwise motor propeller (.L) propeller (.R) 4 = Counter-clockwise motor 3 = Clockwise motor propeller (.R) propeller (.L) CAUTION Risk of injury from flying debris.
-
Page 12: The First Flight
The centre of gravity The centre of gravity of the X44 is located 121-131 mm from the wing leading edge. If the recommended LiPo battery is used, the centre of gravity is automatically correctly adjusted. The centre of gravity can be tested for control by holding the model with two fingers in the centre of gravity under the wing. -
Page 13: Properties
90° by a switch on the transmitter, in this way you can convert before or during the flight from heli to plane model or vice versa. The X44 flies in heli mode as an helicopter and can be flown as an acrobatic plane model in plane mode. -
Page 14: Notes On Environmental Protection
The present construction or user manual is for informational purposes only and may be changed without prior notice. The current version can be found on the Internet at www.graupner.de on the relevant product page. In addition, the company Graupner GmbH has no responsibility or liability for any errors or inaccu- racies that may appear in construction or operation manuals. -
Page 15: Declaration Of Conformity
Declaration of conformity Graupner declares that the product is conform to the CE require- ments Brushless motor KV 1000 EN 61000-6-1: 2007; EN 61000-6-3: 2007/A1: 2011 ESC 12 A EN55014-1: 2006+A1: 2009 EN55014-2: 1997+A2: 2008 Servo EN 6100-6-3: 2007+A1: 2011... -
Page 16: 9944.Rtf_Jh_V1
9944.RTF_jh_V1...
Need help?
Do you have a question about the X44 and is the answer not in the manual?
Questions and answers