Advertisement
Quick Links
OWNER'S MANUAL
INSTALLATION AND OPERATING INSTRUCTIONS
High Pressure Booster Pump
MODEL
HP7C-01
HP7C3-01
HP7D-01
HP7D3-01
HP7E-01
HP7E3-01
HP20E-01
HP20E3-01
HP20F-01
HP20F3-01
STA-RITE INDUSTRIES, INC., DELAVAN, WISCONSIN 53115
Printed in U.S.A. © 1998, Sta-Rite Industries, Inc.
Signature 2000
60 Hz. 1/2 through 1-1/2 HP
HP
1/2
1/2
3/4
3/4
1
1
1
1
1-1/2
1-1/2
1218 0894
PHASE
AVG. GPM
1
3
1
3
1
3
1
3
1
3
7
7
7
7
7
7
20
20
20
20
S327
(Rev. 6/23/98)
Advertisement
Related Manuals for STA-RITE Signature 2000 Series
Summary of Contents for STA-RITE Signature 2000 Series
- Page 1 60 Hz. 1/2 through 1-1/2 HP 1218 0894 MODEL PHASE AVG. GPM HP7C-01 HP7C3-01 HP7D-01 HP7D3-01 HP7E-01 HP7E3-01 HP20E-01 HP20E3-01 HP20F-01 1-1/2 HP20F3-01 1-1/2 STA-RITE INDUSTRIES, INC., DELAVAN, WISCONSIN 53115 S327 (Rev. 6/23/98) Printed in U.S.A. © 1998, Sta-Rite Industries, Inc.
- Page 2 READ AND FOLLOW SAFETY INSTRUCTIONS! This is the safety alert symbol. When you see this symbol on your pump or in this manual, look for one of the following signal words and be alert to the potential for personal injury: DANGER warns about hazards that will cause serious personal injury, death or major property damage if ignored.
- Page 3 INSPECT THE SHIPMENT HIGH PRESSURE BOOSTER PUMP INSTALLATION INSTRUCTIONS The high pressure booster pump has been carefully inspected and packaged to assure safe delivery. These instructions cover high pressure booster pump Inspect the pump and fittings and report to the carrier installations as shown below: any items which are damaged or missing.
- Page 4 LUBRICATION It is not necessary to lubricate pump or motor. The Service Line To Power motor is equipped with sealed ball bearings, lubricated Gate Valve or Hose Bibb for the life of the bearing. The mechanical shaft seal in Male Pipe to Male Hose Adapter the pump is self-lubricating and requires no adjustment.
- Page 5 Disconnect power before working on pump, motor, pressure switch, or wiring. 115 Volt to 230 Volt Conversion, Spade Connector Type: 115 Volt to 230 Volt Conversion, Plug-in Type: Move black wire Change Complete: Move white wire Pull plug Plug in again with black tracer from L1 to A.
- Page 6 To Convert 115 Volts to 230 Volts, Plug-in type Models with factory installed cord and plug: (see Figure 6). Risk of electric shock. This equipment is 1. Unplug the motor. only for use on 115V and is equipped with an approved 3-conductor cord and 3-prong, grounding-type plug.
- Page 7 Impeller Stack Changeout (See Figure 7) shown. Place on motor shaft flats to hold shaft stationary. Remove pump from service and mount vertically in vise (if available) motor side down. Hold at center of 4. With one 7/16” wrench in place on motor shaft, motor.
- Page 8 Mechanical Seal Changeout polished face of seat and press into seal cavity (refer to Figures 7 and 8) using a 3/4” socket or a piece of 3/4” standard pipe. This procedure is best completed with the pump held in a vertical position, motor down. D.
-
Page 9: Limited Warranty
LIMITED WARRANTY Sta-Rite warrants to the original consumer of the products listed below, that they will be free from defects in material and workmanship for the Warranty Period from the date of original installation or manufacture as noted. Product Warranty Period Water Systems Products –... - Page 10 1206 0894 Figure 8 – Exploded view.
-
Page 11: Repair Parts List
REPAIR PARTS LIST HP7C-01 HP7D-01 HP7E-01 HP20E-01 HP20F-01 HP7C3-01 HP7D3-01 HP7E3-01 HP20E3-01 HP20F3-01 Description Qty. 1/2 HP 3/4 HP 1 HP 1 HP 1-1/2 HP Motor - 115/230 Volt, Single Phase A100CHL A100DHL A100EHL A100EHL AE100FHL Motor - 115/230 Volt, Three Phase AP100CH AP100DH AP100EH...
Need help?
Do you have a question about the Signature 2000 Series and is the answer not in the manual?
Questions and answers