Nortel Ethernet Routing Switch 8600 Installation Manual

Chassis

Hide thumbs Also See for Ethernet Routing Switch 8600:

Installing and maintaining (102 pages)

Table of Contents

Quick Links

Download this manual

Nortel Ethernet Routing Switch 8600

Installation — Chassis

Release: 5.0

Document Revision: 02.01

www.nortel.com

NN46205-303

316314-G Rev 01

Table of Contents

Need help?

Do you have a question about the Ethernet Routing Switch 8600 and is the answer not in the manual?

Questions and answers

Summary of Contents for Nortel Ethernet Routing Switch 8600

Page 1 Nortel Ethernet Routing Switch 8600 Installation — Chassis Release: 5.0 Document Revision: 02.01 www.nortel.com NN46205-303 316314-G Rev 01...
Page 2 While the information in this document is believed to be accurate and reliable, except as otherwise expressly agreed to in writing NORTEL PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OF ANY KIND, EITHER EXPRESS OR IMPLIED. The information and/or products described in this document are subject to change without notice.
Page 3: Table Of Contents
Chassis installation procedures 43 Chassis installation time requirements 45 Positioning the chassis on a flat surface 45 Mounting the chassis in an equipment rack 45 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 4 International regulatory requirements 92 8010 chassis 94 Physical specifications 94 Environmental specifications 94 International regulatory requirements 95 8006 chassis 96 Physical specifications 96 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 5 Class A device caution statement 103 Electrostatic discharge caution statement 104 Laser fiber optic warning statement 105 Lifting 8010co chassis warning statement 106 Index Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 7: Regulatory Information And Safety Precautions
Read the information in this section to learn about regulatory conformities and compliances. International Regulatory Statements of Conformity This is to certify that the Nortel 8000 Series chassis and components installed within the chassis were evaluated to the international regulatory standards for electromagnetic compliance (EMC) and safety and were...
Page 8 EN 55 024 Statement This is to certify that the Nortel 8000 Series chassis is shielded against the susceptibility to radio interference in accordance with the application of Council Directive 2004/108/EC. Conformity is declared by the application of EN 55 024 (CISPR 24).
Page 9 Class A requirements of the Republic of Korea Ministry of Information and Communications (MIC). This device may not be sold for use in a non-business application. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 10: National Safety Statements Of Compliance
CE Marking Statement (Europe only) EN 60 950 Statement This is to certify that the Nortel 8000 Series chassis and components installed within the chassis are in compliance with the requirements of EN 60 950 in accordance with the Low Voltage Directive. Additional national differences for all European Union countries have been evaluated for compliance.
Page 11 Norma Oficial Méxicana (NOM): Exportador: Nortel Networks, Inc. 4655 Great America Parkway Santa Clara, CA 95054 USA Importador: Nortel Networks de México, S.A. de C.V. Avenida Insurgentes Sur #1605 Piso 30, Oficina Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright ©...
Page 12 200-240 VCA, 50-60 Hz, 9.3 A max por fuente de poder Model 8004DC: -48 VCD, 29 A Model 8005DC: -48 VCD, 42 A Denan Statement (Japan/Nippon only) Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 13: Safety Messages
This section describes the different precautionary notices used in this document. This section also contains precautionary notices that you must read for safe operation of the Nortel Ethernet Routing Switch 8600. Notices Notice paragraphs alert you about issues that require your attention.
Page 14 14 Regulatory Information and Safety Precautions CAUTION ATTENZIONE ESD Le indicazioni ESD forniscono informazioni per evitare scariche di elettricità statica e i danni correlati per i prodotti Nortel. Caution Notice CAUTION Caution notices provide information about how to avoid possible service disruption or damage to Nortel products.
Page 15 Nortel. WARNING AVISO Os avisos oferecem informações sobre como evitar ferimentos ao trabalhar com os produtos da Nortel. WARNING AVVISO Le indicazioni di avviso forniscono informazioni per evitare danni alle persone durante l’utilizzo dei prodotti Nortel.
Page 16 DANGER PERIGO Avisos de perigo oferecem informações sobre como evitar uma situação ou condição que possa causar graves ferimentos ou morte. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 17 PERICOLO Le indicazioni di pericolo forniscono informazioni per evitare situazioni o condizioni che potrebbero causare gravi danni alle persone o il decesso. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 19: Software License
30 days of purchase to obtain a credit for the full purchase price. "Software" is owned or licensed by Nortel Networks, its parent or one of its subsidiaries or affiliates, and is copyrighted and licensed, not sold. Software consists of machine-readable instructions, its components, data, audio-visual content (such as images, text, recordings or pictures) and related licensed materials including all whole or partial copies.
Page 20 Upon termination or breach of the license by Customer or in the event designated hardware or CFE is no longer in use, Customer will promptly return the Software to Nortel Networks or certify its destruction. Nortel Networks may audit by remote polling or other reasonable means to determine Customer’s Software activation or usage levels.
Page 21 Customer fails to comply with the terms and conditions of this license. In either event, upon termination, Customer must either return the Software to Nortel Networks or certify its destruction. Customer is responsible for payment of any taxes, including personal property taxes, resulting from Customer’s use of the Software.
Page 23: New In This Release
New in this release The following sections detail what’s new in Nortel Ethernet Routing Switch 8600 Installation — Chassis, NN45205-303 for Release 5.0: • “Features” (page 23) • “Other changes” (page 24) Features For information about changes that are feature-related, see the following sections: •...
Page 24: Other Changes
Air filter Information about the air filter in the 8010co chassis is removed. For more information about installing an air filter, see Nortel Ethernet Routing Switch 8600 Installation — 8010co Chassis Air Filter, NN46205-318. For more information about replacing an air filter, see Nortel Ethernet Routing Switch 8600 Routine Maintenance , NN46205-312.
Page 25: Introduction
This document provides the instructions to install the Ethernet Routing Switch 8600 chassis in an equipment rack. This document also describes some of the routine tasks to operate the Ethernet Routing Switch 8600 and includes technical specifications for the chassis and modules.
Page 27: Chassis Installation Fundamentals
Chassis installation fundamentals Each Ethernet Routing Switch 8600 chassis consists of a sheet metal enclosure, a backplane, and a fan interface backplane. The number of bays for power supplies and the number of fan trays and cooling modules depends on the chassis type.
Page 28: 8010Co Chassis
Slots are numbered from left to right. You can install Ethernet Routing Switch 8600 interface modules in slots 1 through 4 and in slots 7 through 10. Slots 5 and 6 are reserved for Ethernet Routing Switch 8600 SF/CPU modules.
Page 29: 8010 Chassis
The 8010co chassis supports the following DC power supplies: • 8004DC • 8005DC If your Ethernet Routing Switch 8600 is operating in a redundant power configuration, you can upgrade the Ethernet Routing Switch 8600 for additional power while the Ethernet Routing Switch 8600 remains in operation. CAUTION The output power ratings differ between power supply models.
Page 30 R or RS modules installed in the 8006, 8010, or 8010co chassis require a minimum of one 8005AC, 8005DI AC, or 8005DC power supply. If your Ethernet Routing Switch 8600 is operating in a redundant power configuration, you can upgrade the Ethernet Routing Switch 8600 for additional power while the Ethernet Routing Switch 8600 remains in operation.
Page 31: 8006 Chassis
For information about power supply installation, see Nortel Ethernet Routing Switch 8600 Installation — AC Power Supply, NN46205-306 or Nortel Ethernet Routing Switch 8600 Installation — DC Power Supply, NN46205-307. The 8010 chassis uses two fan trays for cooling. For information about fan trays, see Nortel Ethernet Routing Switch 8600 Routine Maintenance, NN46205-312.
Page 32: 8003 Chassis
R or RS modules installed in the 8006, 8010, or 8010co chassis require a minimum of one 8005AC, 8005DI AC, or 8005DC power supply. If your Ethernet Routing Switch 8600 is operating in a redundant power configuration, you can upgrade the Ethernet Routing Switch 8600 for additional power while the Ethernet Routing Switch 8600 remains in operation.
Page 33: Power Supplies
The 8003 chassis uses two bays for 8003AC power supplies and a single 8003 fan tray for cooling. For more information about the power supply and fan tray, see Nortel Ethernet Routing Switch 8600 Installation — AC Power Supply, NN46205-306 and Nortel Ethernet Routing Switch 8600 Routine Maintenance, NN46205-312.
Page 34: Fan Trays And Cooling Modules
34 Chassis installation fundamentals If your Ethernet Routing Switch 8600 is operating in a redundant power configuration, you can upgrade the Ethernet Routing Switch 8600 for additional power while the Ethernet Routing Switch 8600 remains in operation. CAUTION The output power ratings differ between power supply models.
Page 35: Site Requirements
For fan trays, a control or monitor circuit board in the fan tray reports temperature and the status of fan operation to the network management software. A green light emitting diode (LED) indicates correct fan operation. For information about installing fan trays, see Nortel Ethernet Routing Switch 8600 Routine Maintenance, NN46205-312. Site requirements Ensure that the installation site meets the space requirements listed in this section.
Page 36 7 "Items in the 8003 chassis shipping container" (page 38) illustrate the items in the chassis shipping container. Figure 5 Items in the 8010 chassis shipping container Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 37 Hardware requirements 37 Figure 6 Items in the 8006 chassis shipping container Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 38 AT-compatible modem to allow dial-in access to startup configuration and diagnostics. Cables Unless you specifically order them, Nortel does not include the cables required for your network configuration in the chassis accessory package. If you need the proper cables, contact your network administrator.
Page 39: 8010Co Chassis
Mount the 8010co chassis in an equipment rack. One upper cable management Manage network interface cables. bracket Two side cable management Manage network interface cables. brackets Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 40 The following sections describe these items. Before you install the 8010co hardware, ensure that you obtain all the cables, tools, and other equipment you need. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 41: Successful Installation Verification
If the rack does not use threaded rail holes, you must use the supplied clip nuts with the clip nut screws. Cables Unless you specifically order them, Nortel does not include the cables required for your network configuration in the 8010co chassis accessory package. If you require the proper cables, contact your network administrator.
Page 42 Contact your network administrator to verify that the Ethernet Routing Switch 8600 is now connected to the network. If the LEDs do not light in this sequence, contact your local Nortel Technical Solutions Center. Nortel Ethernet Routing Switch 8600 Installation —...
Page 43: 8010, 8006, And 8003 Chassis Installation
Prerequisites to chassis installation • Inspect all items for shipping damage. If you find items that are damaged, do not install the chassis. Call the Nortel Technical Solutions Center in your area. • Verify that the items in the shipping container match those on the shipment packing list.
Page 44 Chassis installation procedures Chassis installation navigation • “Reducing the chassis weight” (page 79) • “Positioning the chassis on a flat surface” (page 45) Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 45: Chassis Installation Time Requirements
5 in. (12.7 cm) at the front for power cord clearance. Attach rubber feet to each marked location on the bottom of the chassis. The rubber feet are optional but Nortel recommends that you use them to help keep the unit from moving. --End-- Mounting the chassis in an equipment rack Mount the chassis in a standard 19 in.
Page 46 8006 chassis" (page 47), and Figure 12 "Positioning the rack-mounting brackets: 8003 chassis" (page 47). Figure 10 Positioning the rack-mounting brackets: 8010 chassis Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 47 8006 chassis" (page 48), and Figure 15 "Attaching the rack-mounting brackets to the 8003 chassis" (page 48). Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 48 For more information about the number of rack units to allocate for each chassis, see “Procedure job aid” (page 51). Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 49 Aligning the rack-mounting brackets with the equipment rack: 8010 chassis Figure 17 Aligning the rack-mounting brackets with the equipment rack: 8006 chassis Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 50 Figure 21 "Installing the 8003 chassis in an equipment rack" (page 51). Figure 19 Installing the 8010 chassis in an equipment rack Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 51 Table 5 Number of rack units to allocate for chassis Chassis Rack units Inches 8010 13.2 23.1 8006 16.9 8003 10.5 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 52: Installing The Cable Management Brackets
8003 chassis" (page 53). Figure 22 Loosening the rack-mounting screws: 8010 chassis Figure 23 Loosening the rack-mounting screws: 8006 chassis Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 53 Figure 27 "Securing the bracket to the chassis: 8010 chassis" (page 54), Figure 28 "Securing the bracket to the chassis: 8006 chassis" Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 54 55). Figure 27 Securing the bracket to the chassis: 8010 chassis Figure 28 Securing the bracket to the chassis: 8006 chassis Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 55 Installing the cable management brackets 55 Figure 29 Securing the bracket to the chassis: 8003 chassis --End-- Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 57: 8010Co Chassis Installation
Prerequisites to chassis installation • Inspect all items for shipping damage. If you find items that are damaged, do not install the chassis. Call the Nortel Technical Solutions Center in your area. • Verify that the items in the shipping container match those on the shipment packing list.
Page 58 58 8010co chassis installation Figure 30 Chassis installation procedures Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 59: Chassis Installation Time Requirements
A standard 19-in. or 23-in. equipment rack Attach the clip nuts shipped with the 8010co chassis, if necessary. — 12 Phillips screws and a Phillips screwdriver — Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 60 It requires three people to lift the 8010co chassis. To make the chassis lighter, remove the modules and power supplies before you lift it. Lift the 8010co chassis onto the installation shelf. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 61 Installing the 8010co chassis in a 19-in. two-post rack Make sure that the hole pairs on either side of the vertical support match horizontally. Tighten each screw with a Phillips screwdriver. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 62 Figure 33 "Two 8010co chassis with BIP in a two-post rack" (page shows two 8010co chassis with a BIP installed in a two-post rack. Figure 33 Two 8010co chassis with BIP in a two-post rack Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 63: Installing The Cable Management Brackets
Insert eight screws through the cable management bracket and tighten into chassis. For more information, see the following figure. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 64 To install side cable management brackets, slide the keyed attachments into slots on either side of the card cage. Figure 34 "Installing cable management brackets" (page 64). Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 65: Installing 8004Dc Power Supplies With The Bip
Action Install the 8010co chassis as described in previous procedures. Install the 8004DC power supplies as described in Nortel Ethernet Routing Switch 8600 Installation — DC Power Supply, NN46205-307. Install the BIP as described in Nortel Ethernet Routing Switch 8600 Installation — Breaker Interface Panel, NN46205-313.
Page 66 Rack grounding strip example --End-- Procedure job aid The following figure shows the location of the ground studs on the 8010co chassis rear panel. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 67 BIP. In this example, each chassis uses three 8004DC power supplies. Your rack-grounding strip can look different or can be in a different location than the one shown in the example. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright ©...
Page 68 Cabinet frame or equipment rack AWG 6 ground lead (provided with BIP) Upper shelf chassis ground stud Upper shelf ground lead (not provided) Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 69 The following figure shows an example of how to ground two 8010co chassis. In this example, each chassis uses three AC power supplies. Figure 38 Chassis and AC power supply grounding example Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 70 AWG 6 ground lead (not provided) Rack ground strip (example only) AC equipment ground (ACEG) leads within individual upper shelf cords (x 3) Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 71: Switch Operations
Switch operations This section describes some of the routine tasks you perform to operate the Ethernet Routing Switch 8600. Switch operations navigation • “Powering on DC power supplies” (page 71) • “Powering on AC power supplies” (page 73) • “Resetting the switch” (page 73) •...
Page 72 If you install the 8010co chassis and connect it to the optional BIP, turn the circuit breakers on the BIP to the on position. On each power supply, turn the power switch to the on position. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright ©...
Page 73: Powering On Ac Power Supplies
Resetting the switch 73 If the problem persists, contact the Nortel Technical Solutions Center. --End-- Powering on AC power supplies Power on the AC power supplies to provide power to the switch. Procedure steps Step Action Verify that the AC power cords connect to AC power outlets.
Page 74: Installing Removable Flash Memory Cards
"Inserting a removable flash memory card: 8010co chassis" (page 75) Figure 42 "Inserting a removable flash memory card: 8010, 8006, and 8003 chassis" (page 75). Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 75: Removing Removable Flash Memory Cards
Removing removable ﬂash memory cards Remove a flash memory card from the 8691 SF/CPU module or the 8692 SF/CPU module to stop using it as a storage medium. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 76 Figure 44 "Removing a flash memory card: 8010, 8006, 8003 chassis" (page 77). Figure 43 Removing a flash memory card: 8010co chassis Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 77: Protecting Memory Card Files
Typically, you do not operate a Ethernet Routing Switch 8600 with a write-protected memory card. Make a copy of your configuration on another memory card, write-protect the second card, and store it in a safe place.
Page 78 Insert the card into the card receptacle. Gently push in the card until it fits tightly in place. --End-- Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 79: Common Procedures
Remove the power supply filler panels. For more information, see Nortel Ethernet Routing Switch 8600 Installation — AC Power Supply, NN46205-306 or Nortel Ethernet Routing Switch 8600 Installation — DC Power Supply, NN46205-307. Remove the module filler panels. For more information, see Nortel Ethernet Routing Switch 8600 Installation —...
Page 81: Part Numbers
Part numbers The following table lists Ethernet Routing Switch 8600 hardware and part numbers. Part number Item Additional details DS1400001 8010co chassis Breaker Interface Support for one or two 8010co Panel (BIP) chassis. Includes rack level alarms and cabling from BIP to chassis.
Page 82 8010CMHS high speed cooling module for the 8010 chassis DS1411018-E6 8006CMHS high speed cooling module for the 8006 chassis DS1411019 3-slot chassis rack-mount replacement Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 83: Technical Specifications
“8006 chassis” (page 96) • “8003 chassis” (page 99) Chassis weight The following table provides the chassis weight including components and cables. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 84: Rack-Mount
Input power consumption 770 W Heat dissipation (thermal/output) 920 BTU/hour Hold-up time 20 ms The following table lists the DC output power specifications. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 85: Model 8004Ac Power Supply
(MIL-std 217 standard) Model 8005AC power supply This section provides power ratings for the 8005AC power supply. The following table lists the AC input power specifications. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 86: Model 8005Di Ac Power Supply
(200–240 VAC input voltage) voltage) Input current 16 A 9.3 A Frequency range 50–60 Hz 50–60 Hz Input VA 1556 VA 1753 VA Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 87: Model 8004Dc Power Supply
1850 BTU/hour If you install a Breaker Interface Panel (BIP), the installation site must meet the electrical requirements for DC power shown in the following table. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 88: Model 8005Dc Power Supply
Output power (maximum) 1462 W (1372 W + 90 W fans) Modules 3.3 VDC @ 150 A 12 VDC @ 72 A Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 89: Component Input Power
You can also calculate chassis and module power consumption using the Nortel ERS 8600 Power Supply Calculator (NN48500-519), available on the Nortel Technical Support Web site. You can find the calculator at www.nortel.com/documentation. Choose Routers & Routing Switches, and then Ethernet Routing Switch 8600.
Page 90: Power Supply Selection
Power supply selection The following table lists the power available from each power supply supported with the Ethernet Routing Switch 8600. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard...
Page 91: 8010Co Chassis
8010co chassis 91 Release 5.0 of the Ethernet Routing Switch 8600 offers improved power management. Power management identifies the available power in the chassis, called the power budget, and determines if enough power is available to operate the installed components. For a complete description of the power management feature and configuration instructions, see Nortel Ethernet Routing Switch 8600 Administration, NN46205-605.
Page 92: Network Equipment Building Standard
The 8010co chassis conforms to the following international regulatory requirements: • “Electromagnetic emissions” (page 93) • “Electromagnetic immunity” (page 93) • “Safety agency certification” (page 93) Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 93 IEC 60950 current edition with all CB member deviations UL60950 Canada CSA 22.2 No. 60950 Europe EN60950 (CE Marking) Australia/New Zealand AS/NZS 3260 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 94: 8010 Chassis
Storage temperature – 25 C to 70 C (– 13 F to 158 F) Operating humidity 85% maximum relative humidity, noncondensi Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 95: International Regulatory Requirements
ICES-003, Issue-2, Class A Europe EN 55022-1998 Class A; EN 61000-3-2/A14, Electromagnetic immunity The 8010 chassis conforms to the following electromagnetic immunity standards. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 96: 8006 Chassis
17.5 in. (44.5 cm) Depth 19.9 in. (50.5 cm) Weight (empty) 49 lb (22 kg) Weight (fully loaded) 140 lb (63 kg) Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 97 The 8006 chassis conforms to the following international regulatory requirements: • “Electromagnetic emissions” (page 98) • “Electromagnetic immunity” (page 98) • “Safety agency certification” (page 98) Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 98: Electromagnetic Emissions
IEC 60950 current edition with all CB member deviations UL60950 Canada CSA 22.2 No. 60950 Europe EN60950 (CE Marking) Australia/New Zealand AS/NZS 3260 Mexico NOM-019-SCFI-1998 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 99: Chassis
95% maximum relative humidity, noncondensi Operating altitude 3024 m (10 000 ft) maximum Storage altitude 3024 m (10 000 ft) maximum Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 100 Japan VCCI-V3/97.04, Class A Taiwan CNS 13438, Class A Electromagnetic immunity The 8003 chassis conforms to the following electromagnetic immunity standards. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 101 IEC 60950 current edition with all CB member deviations UL60950 Canada CSA 22.2 No. 60950 Europe EN60950 (CE Marking) Australia/New Zealand AS/NZS 3260 Mexico NOM-019-SCFI-1998 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 103: Translations Of Safety Messages
área residencial provavelmente causará interferência prejudicial; neste caso, espera-se que os usuários tomem as medidas necessárias para corrigir a interferência por sua própria conta. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 104: Electrostatic Discharge Caution Statement
(ESD) quando estiver realizando a manutenção deste produto. Certifique-se de que a pulseira esteja em contato com sua pele. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 105: Laser Fiber Optic Warning Statement
Nunca mire un puerto de fibra óptica o conector. Siempre asuma que los cables de fibra óptica están conectados a una fuente de luz. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 106: Lifting 8010Co Chassis Warning Statement
Riesgo de lesiones Se necesitan tres personas para levantar el chasis de 8010co. Para alivianar el peso, retire los módulos y las fuentes de alimentación antes de levantarlo. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 107 Rischio di lesioni personali Per sollevare lo chassis 8010co, sono necessarie tre persone. Per alleggerire lo chassis, rimuovere i moduli e gli alimentatori prima di sollevarlo. Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008...
Page 109: Index
LEDs 41 installing 8003 43 8006 43 8010 43 management console 38 8010co 57 memory cards operating 71 changing read-write protection 77 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 110 8010co chassis 39 site requirements 35 space requirements 35 statements of compliance 7, 10 statements of conformity 7 troubleshooting power-up sequence 41 Nortel Ethernet Routing Switch 8600 Installation — Chassis NN46205-303 02.01 Standard 30 May 2008 Copyright © 2008 Nortel Networks...
Page 112 While the information in this document is believed to be accurate and reliable, except as otherwise expressly agreed to in writing NORTEL PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OF ANY KIND, EITHER EXPRESS OR IMPLIED. The information and/or products described in this document are subject to change without notice.

Nortel Ethernet Routing Switch 8600 Installation Manual

Regulatory Information and Safety Precautions

Software License

New in this Release

Introduction

Chassis Installation Fundamentals

8010, 8006, and 8003 Chassis Installation

8010Co Chassis Installation

Switch Operations

Common Procedures

Part Numbers

Technical Specifications

Translations of Safety Messages

Index

Quick Links

Need help?

Questions and answers

Related Manuals for Nortel Ethernet Routing Switch 8600

Summary of Contents for Nortel Ethernet Routing Switch 8600

Table of Contents