Siemens MICROMASTER 430 Manual page 70

PI Controller (P0004 = 22)
MICROMASTER 430
6SE6400-5AC00-0BP0
www.eltra-trade.com
ParNr ParText
P2167[3] Switch-off frequency f_off
P2168[3] Delay time T_off
r2169 CO: Act. Filtered frequency
P2170[3] Threshold current I_thresh
P2171[3] Delay time current
P2172[3] Threshold DC-link voltage
P2173[3] Delay time DC-link voltage
P2174[3] Torque threshold T_thresh
P2176[3] Delay time for torque threshold
P2177[3] Delay time for motor is blocked
P2178[3] Delay time for motor pulled out
P2179 Current limit for no load ident.
P2180 Delay time for no load ident.
P2181[3] Belt failure detection mode
P2182[3] Belt threshold frequency 1
P2183[3] Belt threshold frequency 2
P2184[3] Belt threshold frequency 3
P2185[3] Upper torque threshold 1
P2186[3] Lower torque threshold 1
P2187[3] Upper torque threshold 2
P2188[3] Lower torque threshold 2
P2189[3] Upper torque threshold 3
P2190[3] Lower torque threshold 3
P2192[3] Time delay for belt failure
r2197 CO/BO: Monitoring word 1
r2198 CO/BO: Monitoring word 2
ParNr ParText
P2200[3] BI: Enable PID controller
P2201[3] Fixed PID setpoint 1
P2202[3] Fixed PID setpoint 2
P2203[3] Fixed PID setpoint 3
P2204[3] Fixed PID setpoint 4
P2205[3] Fixed PID setpoint 5
P2206[3] Fixed PID setpoint 6
P2207[3] Fixed PID setpoint 7
P2208[3] Fixed PID setpoint 8
P2209[3] Fixed PID setpoint 9
P2210[3] Fixed PID setpoint 10
P2211[3] Fixed PID setpoint 11
P2212[3] Fixed PID setpoint 12
P2213[3] Fixed PID setpoint 13
P2214[3] Fixed PID setpoint 14
P2215[3] Fixed PID setpoint 15
Operating Instructions
5 System parameters
Default Level DS QC
1.00 3 CUT N
10 3 CUT N
- 3 - -
100.0 3 CUT N
10 3 CUT N
800 3 CUT N
10 3 CUT N
5.13 3 CUT N
10 3 CUT N
10 3 CUT N
10 3 CUT N
3.0 3 CUT N
2000 3 CUT N
0 3 CT N
5.00 3 CUT N
30.00 3 CUT N
50.00 3 CUT N
99999.0 3 CUT N
0.0 3 CUT N
99999.0 3 CUT N
0.0 3 CUT N
99999.0 3 CUT N
0.0 3 CUT N
10 3 CUT N
- 3 - -
- 3 - -
Default Level DS QC
0:0 2 CUT N
0.00 3 CUT N
10.00 3 CUT N
20.00 3 CUT N
30.00 3 CUT N
40.00 3 CUT N
50.00 3 CUT N
60.00 3 CUT N
70.00 3 CUT N
80.00 3 CUT N
90.00 3 CUT N
100.00 3 CUT N
110.00 3 CUT N
120.00 3 CUT N
130.00 3 CUT N
130.00 3 CUT N
+421 552 601 099
69
info@eltra-trade.com