Parts List; Troubleshooting And Maintenance - Elkay SWIRLFLO Series Installation, Care & Use Manual

RESTROOM DIREC T
distributed by
EDFPB117C, EDFPBM117C, EDFPB117RAC, EDFPBM117RAC, EDFPBV117C,
EDFPBMV117C, EDFPBV117RAC, EBFPBMV117RAC

PARTS LIST

ITEM NO.
PART NO.
1 56073C Bubbler Assy
2 40319C Fitting - Orifice
3
50171C O-Ring
4 50314C
Orifice - Flow Straightener
5 56011C
Housing Assembly
6 55997C Pedestal
7 75580C Bubbler Locknut
8 98118C Bubbler Assembly VR
9 100322740560 Gasket - Black .68 x 1.03 VR
10 15009C Nipple - Bubbler VR
11 28474C Basin - Swirlflow
12 28473C Lower Shell
13
45767C Fountain Body
14 28343C
Cover Plate
15 45781C
Sleeve
16 45847C Pin - Push Button
17 45848C Push Button
18 50986C Holder - Regulator
19 61313C Regulator
20 15005C Retaining Nut
21 56163C Gasket - Drain
22 45769C Assy - Drain/Tailpipe
23
45768C Drain - Plug 1-1/2"
24 56092C
Poly Tubing (Cut To Length)
25 28392C
Back Panel RH ADA
28393C Back Panel LH ADA
26 AP99 AP-99 Panel (Optional)
27 111008343890 Screw - #10-24 x .62 HHMS
28 70432C Screw - #8-32 x .38 THSM
29 38417001 Screw - #8-18 x .37 HHSM
30 75560C Screw - 5/16-18 x 1.00 HHMS
31 75632C Setscrew - #10-32 x .31
32
70817C Fttng - Elbow 1/4 x 1/4
33 55996C
Strainer
34 75671C
Spring - Push Button
35 28844C Back Panel Assy RH ADA
28845C Back Panel Assy LH ADA
NS 27090C Hanger Bracket
Figure 16 – Back Panel Assembly
Installing Back Panel: When installing back panel
assy. (Item 35) with MPW (Mounting Plate), attach
channel braces as shown above. Remove the
protective backing from the tape installed on the
braces. Line up the corresponding holes in the
braces and back panel and press firmly in place.
PRINTED IN U.S.A.
ELKAY MANUFACTURING COMPANY · 2222 CAMDEN COURT · OAK BROOK, IL 60523 · 630.574.8484
704 . 937. 2673
TROUBLESHOOTING & MAINTENANCE
DESCRIPTION
can cause water flow to spurt or not regulate. Mineral
deposits may be removed from the orifice by poking
with a small round file not over 1/8" diameter, or using a
small diameter wire.
flow as in Step 8 of the installation instructions. If
replacement is necessary, see parts list for correct
regulator part number.
Fittings:
tors which utilize an o-ring water seal. To remove
tubing from the fitting, relieve water pressure, push in
on the gray collar while pulling on the tubing. (See
Figure 15) To insert tubing, push tube straight into
fitting until it reaches a positive stop (approximately 3/4").
35
1/4" O.D. TUBE
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
Page 9
www.RestroomDirect.com
Orifice Assembly: Mineral deposits on orifice
!
CAUTION:
DO NOT file or cut orifice
material.
Stream Regulator: If orifice is clean, regulate
Actuation of Quick Connect Water
Cooler is provided with lead-free connec-
Figure 15 – Quick Connect Fittings
33
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
WATER INLET
TO COOLER
NOTE: WATER FLOW
DIRECTION
Figure 17 – Water Supply Connections
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
97922C (Rev. G - 6/08)