Table of Contents
Advertisement
SWIRLFLO
EZWS-ERPBM28K
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an "electrolysis" effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain fittings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building's plumbing circuits.
ERPBD28WSC
INSTALLATION & USE MANUAL
Refrigerated fountains with FLEXI-GUARD
®
and ezH2O
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
LRPBD2_8WSC
Bottle Filler
®
LZWS-LRPBM28K
Page 1
®
0000001030 (Rev. K - 03/19)
Advertisement
Table of Contents
Related Manuals for Elkay SWIRLFLO LRPBD2 8WSC Series
Summary of Contents for Elkay SWIRLFLO LRPBD2 8WSC Series
- Page 1 ERPBD28WSC LRPBD2_8WSC INSTALLATION & USE MANUAL SWIRLFLO Refrigerated fountains with FLEXI-GUARD ® ® and ezH2O Bottle Filler ® LZWS-LRPBM28K EZWS-ERPBM28K INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
- Page 2 ERPBD28WSC LRPBD2_8WSC Figure 1 - Rough-in Dimensions Page 2 0000001030 (Rev. K - 03/19)
- Page 3 ERPBD28WSC LRPBD2_8WSC REQUIRED TOOLS AND MATERIALS These tables show special tools and/or additional materials (not provided) which are necessary to complete installation of these units: TO BUBBLER Special Tools TO BOTTLE Item Description Quantity FILLER NONE CHILLER Additional Materials Not Included OUTLET CHILLER Item...
- Page 4 ERPBD28WSC LRPBD2_8WSC 8. Install fountains with (8) 5/16-18 HHMS & (8) 5/16-18 nuts (provided) (Fig. 4). Connect the ¼” water lines from each fountain to the remaining openings on the tee at the remote Reset chiller (cut lines to fit as needed). Switch 9.
- Page 5 ERPBD28WSC LRPBD2_8WSC See Fig. 6 See Fig. 6 Figure 7 - Fountain Body Assembly FIVE PIN CONNECTOR MAIN BOARD FOUR PIN CONNECTOR WHITE I.R. BOARD SOLENOID WHITE NEUTRAL BLACK LINE VOLTAGE LED BOARD GROUND GREEN GROUND VIOLET NOT USED CAPPED MALE YELLOW PLUG...
- Page 6 ERPBD28WSC LRPBD2_8WSC BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE Continued from below: 1) To verify the software program of the control board the unit will 3) When display shows “UNIT TYPE” push program button once the need to be shut down and restarted.
- Page 7 ERPBD28WSC LRPBD2_8WSC MOUNTING FRAME JUNCTION MAIN PANEL REMOTE CHILLER DRAIN LOCATIONS FILTER MOUNTING (OPTIONAL) FRAME LOWER PANEL Figure 9 3/8” Water Inlet WATERSENTRY PLUS FILTER PARTS LIST ® (See Fig. 10) ITEM PART DESCRIPTION Filter Assy-3000 Gal. 51300C Kit-Filter Head Fittingsk-includes John Guest 98926C Fittings 51469C...
- Page 8 Figure 12 FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816 REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com Page 8 0000001030 (Rev. K - 03/19)
Need help?
Do you have a question about the SWIRLFLO LRPBD2 8WSC Series and is the answer not in the manual?
Questions and answers
Filter status does not reset after filter change
To reset the filter status on the Elkay SWIRLFLO LRPBD2 8WSC Series after a filter change:
1. Press the button until the display shows “SETTINGS.”
2. Wait for approximately 4 seconds until the display changes.
3. Navigate to “FLT SIZE” to select the filter capacity if needed.
4. Locate and select “RST BCNT” to reset the bottle count.
5. The display will return to run mode after the reset is complete.
This answer is automatically generated