Installation Instructions - Elkay SWIRLFLO Series Installation, Care & Use Manual

RESTROOM DIREC T
distributed by
EDFPB117C, EDFPBM117C, EDFPB117RAC, EDFPBM117RAC, EDFPBV117C,
Figure 9 -Panel Installation
30
14
28
Figure 10 - Fountain Installation
Figure 11 - AP-99 Panel (Optional)
97922C (Rev. G - 6/08)
704 . 937. 2673
EDFPBMV117C, EDFPBV117RAC, EBFPBMV117RAC

Installation Instructions:

1. Fountains using the MPW Mounting Plate refer to Figures
25
2. Shown dimensions pertain to installation location (framing must
3. Install rough-in plumbing as shown in Fig's. 1, 3, 5, or 7. Run
4. Installing back panel.
5. Install fountain. Remove screw (Item 28) from cover
6. Determine required length of waste line and cut to
7. Make water supply connections from service stop to the
8. These products are designed to operate on 20-105 PSIG supply
9. Check stream height from bubbler. Stream height is factory set at
26
Page 6
www.RestroomDirect.com
5 or 7 for hanger bracket location and rough-in dimensions.
NOTE: Review separate installation instructions for details of the
MPW Mounting Plate.
Fountains using the Wall Plate Assy. refer to Fig's. 1 or 3
for rough-in dimensions.
support up to 300 lbs. weight). These dimensions are required for
compliance with ANSI Standard A117.0.
supply water inlet line through the back panel. Install a service
stop (not provided). Turn on supply water and flush thoroughly.
Ftn. w/MPW Mounting Plate: Refer to Fig. 16 for placement
of braces onto back panel. Place the upper edge of the panel
above the hanger bracket. Slide the panel down until it engages
the hanger bracket. Be sure back panel is firmly engaged before
releasing it.
Ftn. w/Wall Plate Assy.: Place the upper edge of the panel
above mounting plate on the wall. Slide the panel down until it
engages the mounting plate. Be sure back panel is firmly engaged
before releasing it. (See Figure 9)
plate and slide cover plate (Item 14) toward basin. (See Figure 10)
Ftn. w/MPW Mounting Plate: Mount the fountain to the back
panel and wall using (4) 5/16" x 6" long threaded rods, washers,
and nuts (provided). Tighten securely.
Ftn. w/Wall Plate Assy.: Mount the fountain to the back panel
and wall plate assy. with (4) 5/16" x 1" (25mm) long screws
(Item 30 - provided). Tighten securely.
appropriate length. 1-1/4" O.D. waste tube furnished.
1-1/4" slip trap, waste elbow and extension not provided.
3/8" O.D. unplated copper tube coming out of the strainer. Turn on
water supply and check for leaks (See Figure 17). Newly installed
water supply line should be insulated after leak check is
completed.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to the
o-rings may result.
line pressure. If the inlet pressure is above 105 PSIG, a pressure
regulator must be installed in the supply line. Any damage caused
by reason of connecting these products to supply line pressures
lower than 20 PSIG or higher than 105 PSIG is not covered by
warranty.
35 PSI. If supply pressure varies greatly from this, remove push
button (Item 17 - Figure 14) and adjust the screw on the regulator
(Item 19 - Figure 14). To remove push button, remove setscrew
from bottom of sleeve (Item 15). Insert a small punch in screw
hole and push up while grasping the push button and pull forward
removing the push button. Clockwise adjustment will raise stream
height and counterclockwise movement will lower stream height.
For best adjustment stream should hit basin approximately 6-1/2"
from the bubbler. Reassemble the push button by pushing in on
button until the push button catches in the sleeve. Reinstall the
setscrew (Item 31) in the sleeve (Item 15).