Advertisement
Quick Links
FLUENT
®
Wide Spread Lavatory Faucet
with Speed Connect
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Flat Head Screwdriver
INSTALL SPOUT
1
Fig. A.
Insert (1) CABLE CONNECTOR (2) and HOSE (3) through center hole,
making sure SEAL WASHER (4) is properly seated in spout base.
Assemble RUBBER WASHER (5), LOCKNUT (6) and thread LOCKNUT (6)
onto SHANK (7) from underside of sink or mounting surface.
Align and center SPOUT (1). Tighten LOCKNUT (6).
INSTALL VALVE BODIES
1A
Fig. B.
Remove LOCKNUT (8) and RUBBER WASHER (9) from
SIDE VALVE SHANKS (10).
Insert Hot and Cold SIDE VALVE HOSES (11), FLEXIBLE
SUPPLIES (11a) into mounting holes making sure the SEAL
WASHERS (12) are properly seated in each HANDLE BASE (13).
Assemble RUBBER WASHER (9) and thread
LOCKNUT (8) onto each SIDE VALVE
SHANK (10) from underside of sink
or mounting surface.
Align and center SIDE VALVES.
Tighten LOCKNUTS (8).
®
Drain
Slip Jaw Pliers
Turn off hot and cold water
CAUTION
supplies before beginning.
13
12
10
9
Fig. B.
8
11 Red Stripe (HOT)
Installation
Instructions
7186.801
7186.811
Tubing Cutter
Adjustable Wrench
11a
11a
1
Certified to comply with ANSI A112.18.1
M965622 Rev. 1.2 (12/17)
Fig. A.
SPOUT BASE
1
11 Blue Stripe (C0LD)
4
7
5
6
3
2
Advertisement
Related Manuals for American Standard FLUENT 7186.801
Summary of Contents for American Standard FLUENT 7186.801
- Page 1 M965622 Rev. 1.2 (12/17) • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect drain. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
- Page 2 POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). BODY Tighten TAILPIECE (4) on DRAIN BODY before Fig. B. installing DRAIN BODY. REMOVE FLANGE Fig. A. Fig. B. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain Fig.
- Page 3 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto CABLE ATTACHMENT POINT (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig.
-
Page 4: Care Instructions
TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3). CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. -
Page 5: Troubleshooting Guide
® Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •... - Page 6 LOGO the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H.
- Page 7 FLUENT ® Wide Spread Lavatory Faucet with Speed Connect ® Drain MODEL NUMBERS M964919-YYY0A LEVER HANDLE (LEFT) 7186.801 M964920-YYY0A 7186.811 LEVER HANDLE (RIGHT) M964923-YYY0A LIFT ROD AND KNOB M964479-0070A AERATOR (1.2 GPM) A911757-0070A SEAL M904924-0070A CARTRIDGE NUT M964005-0070A CARTRIDGE M964922-YYY0A HANDLE BASE M904521-0070A T-CONNECTOR...