Summary of Contents for Feig Electronic OBID ID RWA02.ABCD Series
Page 1
Montageanleitung / Mounting Instruction ID RWA02.ABCD Version: -A / -B Version: -AL / -BL (Leser mit Gehäuse) (Leser ohne Gehäuse) (Reader with Case) (Reader without Case) (deutsch / english) M71191-5de-ID.DOC...
Page 2
® Identifikation System OBID deutsche Version ab Seite 3 english version from page 15 Seite 2 von 26 FEIG ELECTRONIC GmbH...
Page 3
Da sich Fehler, trotz aller Bemühungen nie vollständig vermeiden lassen, sind wir für Hinweise jederzeit dankbar. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung dafür, dass die in diesem Dokument enthaltenden Infor- mationen frei von fremden Schutzrechten sind. FEIG ELECTRONIC GmbH erteilt mit diesem Dokument keine Lizenzen auf eigene oder fremde Patente oder andere Schutzrechte.
Nachmessen sicherzustellen, dass das Gerät spannungslos ist. • Das Verlöschen einer Betriebsanzeige ist kein Indikator dafür, dass das Gerät vom Netz getrennt und spannungslos ist. Bei Arbeiten am geöffneten Gerät ist zu beachten, dass evtl. spannungsführende Teile freiliegen. FEIG ELECTRONIC GmbH Seite 5 von 26...
2.2 ID RWA02.ABCD-AL / -BL 1 x ID RWA02.ABCD -AL oder -BL 1 x Montageanleitung 3. Reihenfolge der Montage Anschluß nach Tabelle 1 und Bild 1, 2, 3 Wandmontage Inbetriebnahme Klarsichtdeckel montieren Aufkleber montieren Seite 6 von 26 FEIG ELECTRONIC GmbH...
Leser mit RS232 Schnittstelle werden nach dem in Bild-3 dargestellten Schema mit dem Leitrech- ner verbunden. Leitrechner gelb / 8 grün / 7 ID RS02 blau / 4 Bild 3: RS232 Anschluß ID RWA02.ABCD-A / -AL Seite 8 von 26 FEIG ELECTRONIC GmbH...
Schrauben direkt auf eine solche Schalterdose geschraubt werden. Ist eine Montage auf einer Metalloberfläche notwendig, kann zur Einhaltung des Mindesabstandes der Gehäuserahmen ID APG-A von FEIG ELECTRONIC bezogen werden. Hinweis; Nach Abschluß der Klemm- und Montagearbeiten und noch vor der Befestigung des Auf- klebers sollte die Funktion getestet werden! 5.2 ID RWA02.ABCD-AL/ -BL:...
ID RWA gespeichert. 3. Wurden alle Parameter ausgelesen und gespeichert wird die grüne LED und der Beeper für 800 ms aktiv. ® 4. Danach kann eine weitere OBID MasterCard von dem ID RWA eingelesen werden. Seite 10 von 26 FEIG ELECTRONIC GmbH...
Default-Wert(en) initialisiert. gelb blinken Offline-Mode Keine Kommunikation (Multi-Job-Poll) zwischen Host und ID RWA gelb Online-Mode Kommunikation (Multi-Job-Poll) zwischen Host und ID RWA besteht Werkseinstellung, kann individuell geändert werden. Werkseinstellung, kann individuell geändert werden. FEIG ELECTRONIC GmbH Seite 11 von 26...
Alle Leser zeigen mit der gelben Farbe der LED ihre Funktionsbereitschaft an. Voraussetzung ist, daß die Anzeige der Signalgeber in der Werkseinstellung bleibt und die Eingänge geöffnet sind. Eine vollständige Funktionskontrolle ist nur mit einem Terminal bzw. einem Leitrechner möglich. Seite 12 von 26 FEIG ELECTRONIC GmbH...
60,0 mm 13,5 mm 3,5 mm 3,5 mm Gehäuseöffnung für LED und DIP 47,0 mm 80,0 mm 18,0 mm 15,5 mm Bild 5: Abmessungen ID RWA02.ABCD-A /-B Bild 6: Abmessungen ID RWA02.ABCD-AL /-BL FEIG ELECTRONIC GmbH Seite 13 von 26...
9600 Baud, 8 Daten- 1 Stopbit, even Parity • Adresse im EEPROM: 0 (wird priorisiert, wenn Adresse im EEPROM > 0) • Adresse des DIP-Schalters 0 (wird priorisiert, wenn Adresse im EEPROM = 0) • LED-Betriebsanzeige orange Seite 14 von 26 FEIG ELECTRONIC GmbH...
Page 15
Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information.
Page 16
6. Operation: ........................22 ® 6.1 Configuration with the OBID MasterCard ..............22 6.2 LED and beeper indications..................... 23 6.3 Setting the Addresses...................... 24 6.4 Function Control....................... 24 7. Dimensions ........................25 8. Technical Data ......................26 Page 16 of 26 FEIG ELECTRONIC GmbH...
Please switch off the power supply before opening the device and make sure that it is idle. The fact that an operational display goes out does not necessarily mean that the device is disconnected from the power supply and idle. FEIG ELECTRONIC GmbH Page 17 of 26...
1 x installation instructions 3. Respect the order of the installation: 1. connection according to table 1 and figure 1, 2 2. wall-installation 3. operation test 4. attaching the transparent top 5. fixing the adhesive label Page 18 of 26 FEIG ELECTRONIC GmbH...
Readers with RS232 interface have to be connected to the host according to fig 3: connection of the RS232-interface". Host yellow / 8 green / 7 Reader blue / 4 fig 3: connection of the RS232-interface Page 20 of 26 FEIG ELECTRONIC GmbH...
- the transponder should be hold area-parallel to the antenna. The distance between the reader antenna to conducting materials should be of minimum 3 cm. Otherwise, the reading range will be decreased. FEIG ELECTRONIC GmbH Page 21 of 26...
MasterCard and store’s it in the EEPROM. ® 3. After reading and storing the OBID MasterCard the green LED and the beeper are active for 800 ms. ® 4. After this further OBID MasterCard’s could be read and stored. Page 22 of 26 FEIG ELECTRONIC GmbH...
Offline-Mode Communication time out (Multijob-Poll) between Host and ID RWA orange Online-Mode valid communication (Multijob-Poll) between Host and ID RWA Default configuration, may changed individual Default configuration, may changed individual FEIG ELECTRONIC GmbH Page 23 of 26...
An orange coloured LED (all readers) indicates : ready to operate / waiting. A requirement for this is that the indicator-configuration has not been modified and that all inputs are open. A complete function control can only be carried out with a terminal res. central PC. Page 24 of 26 FEIG ELECTRONIC GmbH...