Rb398S/Rb518/Rb218 Safety Features - Max Rebartier RB398S Instruction Manual And Safety Instructions

• Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
• Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
• When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
• Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
• Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
• Do not use the power tool in the rain, where water is
splashing, in a wet place, or in a damp place. Using the tool
in these or similar conditions will increase the risk of electric
shock, dangerous malfunction, and overheating.
• DO NOT DISPOSE OF BATTERY PACKS/BATTERIES
INTO FIRE OR WATER. Battery packs/batteries should be
collected, recycled or disposed of in an environmental-friendly
manner.
• PROTECT THE BATTERY AGAINST HEAT, ALSO
AGAINST CONTINUOUS SUN IRRADIATION AND FIRE.
There is danger of explosion.
• CHARGE THE BATTERY PACK IN A TEMPERATURE
RANGE 41°F (5°C) TO 104°F (40°C).
• DO NOT DISPOSE OF POWER TOOLS INTO HOUSEHOLD
WASTE. According to the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are no
longer usable must be collected separately and disposed of in
an environmentally correct manner.
• DEFFECTIVE OR DEAD OUT BATTERY PACKS/
BATTERIES MUST BE RECYCLED ACCORDING TO THE
GUIDELINE 2006/66/EC.
4. RB398S/RB518/RB218 SAFETY
FEATURES
1. INSPECT THE PARTS BEFORE MOUNTING THE
BATTERY PACK
• Examine the screws to make sure they are securely
tightened.
Incomplete tightening may result in an accident or
breakage. If a screw is loose, retighten it completely.
• Inspect parts for damage.
Parts will wear over periods of use. Look also for missing
and defective parts and for parts of poor quality. If a part
must be replaced or repaired, purchase the replacement
part at the dealer where the tool was purchased or MAX
CO., LTD. authorized distributors.
Use only genuine authorized replacement parts.
2. SET THE MAIN SWITCH (FIG.6.7) AT "OFF", THE
TRIGGER LOCK (FIG.6.8) AT "LOCK" AND
REMOVE THE BATTERY PACK (FIG.6.0), WHEN
CHANGING THE BATTERY PACK, REPLACING OR
ADJUSTING THE TIEWIRE, ABNORMALITIES
OCCUR, AND THE TOOL IS NOT BEING USED
Leaving the tool switched on in these situations may cause
breakdowns or damage.
3. KEEP FINGERS AND BODY PARTS CLEAR
BETWEEN THE ARM AND CURL GUIDE AT ALL
TIMES (FIG.16)
Failure to do so may result in serious injury.
4. KEEP FINGERS AND BODY PARTS AWAY FROM
THE TIEWIRE WHEN TOOL IS IN OPERATION
Failure to do so may result in serious injury.
5. DO NOT POINT THE TOOL AT ANYONE
Personal injury may result if the tool catches an operator or
anyone working near him/her. While working with the tool, be
extremely careful not to bring hands, legs, and other body
parts near the arm of the tool.
6. WHEN THE TOOL IS NOT IN OPERATION KEEP
YOUR FINGERS OFF THE TRIGGER
Failure to do so may cause accidental tying, leading to
serious injury.
7. NEVER OPERATE THE TOOL UNDER ANY
ABNORMAL CONDITION
If the tool is not in good working order, or if any abnormal
condition is noticed, switch it off immediately (set the Main
switch at "OFF"), lock the Trigger and have it examined and
repaired.
8. AFTER BATTERY INSTALLATION IF THE TOOL
OPERATES WITHOUT THE TRIGGER BEING
PULLED OR THE OPERATOR NOTICES UNUSUAL
HEAT, SMELL, OR SOUND, DISCONTINUE
OPERATION
Failure to do so may lead to serious injury. Return to dealer
for safety inspection.
9. NEVER MODIFY THE TOOL
Modifying the tool will impair performance and operating
safety. Any modification may lead to serious injury and void
the tool warranty.
10. MAINTAIN THE TOOL IN GOOD OPERATING
CONDITION
To secure operating safety and ensure top performance,
keep the tool free of wear and damage. Also keep the tool's
hand grip dry and clean, especially free of oil and grease.
8