Advertisement
Quick Links
Home (/) > Knowledge Base - Home (/knowledgebase/) > KA-01080
CL600 - Installation Instructions
Contents
Check that the contents of your box are correct according to the model.
1 Front plate and handle
2 Back plate and handle
3 Neoprene seals x 2
4 RED & BLUE tipped spindles
5 Fixing bolts x 4 (1 x spare)
6 Front plate cylinder cover
7 Allen keys x 2
8 Euro profile cylinder escutcheons
8a Keyhole escutcheons
9 Mortice latch, strike & 4 screws
10 2 bolt mortice lock and strike
11 Double Europrofile cylinder & 3 keys -
12 Code change keys
Adaptor kit for mortice locks
13
with horizontal fixings
14 Latch support post
15 Code change tool
Installation template
Code change instructions
Code card
Fire Kit (optional)
Tools Required for installation:
• Power drill
• Drill bits 30mm (1 ⁄ "), 25mm (1"), 20mm ( ⁄ "), 16mm ( ⁄ ") & 10mm ( ⁄ ")
• Phillips screwdriver
• Chisel - 22mm ( ⁄ ")
• Chisel - 25mm (1")
• Hammer/Mallet
• Stanley knife
• Adhesive tape
• Pencil
• Bradawl
• Tape measure
Model 600/605 Model 610/615 Model 620/625
1 pair
-
1 pair
-
-
-
-
-
-
-
-
(See page 13) -
Print
Views: 203
1 pair
-
-
-
-
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SDC CL600 Series
Summary of Contents for SDC CL600 Series
- Page 1 Home (/) > Knowledge Base - Home (/knowledgebase/) > KA-01080 CL600 - Installation Instructions Print Views: 203 Contents Check that the contents of your box are correct according to the model. Model 600/605 Model 610/615 Model 620/625 1 Front plate and handle ...
- Page 2 Check operation of the code front plate. On models CL605, CL615 and CL625 a free passage function is available. This is identified by a black dot on the bottom left hand ’Z’ button. In normal operation the code needs to be entered every time to retract the latch.
- Page 3 If your lockcase has a hole below the follower (Figure 1 ‘A’), proceed as follows: Step 1 Hold the neoprene seal with the three fixing holes against the door, vertically, with the rectangular hole centrally over the follower. Mark the top and bottom holes on the door face, and repeat the procedure on the other side of the door.
- Page 4 Fit remaining spindle to inside - non code side. Step 3 Take the adaptor kit, item 13 on the contents page. Cut the two M5 countersunk head bolts to length to suit the door thickness; i.e. door thickness plus a maximum of 10mm ( ⁄ ”) (no more than 5mm ( ⁄ ”) should enter the front plate).
- Page 5 Note: Space required above latch body for cam to rotate. Step 2 Keeping the drill level and square to the door, drill a 25mm (1”) hole in centre of door edge, deep enough to accept the latch. Step 3 Keeping the drill level and square to the door, drill the 10mm and 30mm ( ⁄ ”- 1 ⁄ ”) holes from both sides of the door to increase accuracy and to avoid splintering out the door face.
- Page 6 Step 11 Fix the two plates together using the socket head bolts, starting with the top fixing. Ensure that the two plates are truly vertical and then tighten the bolts using the ‘T’ shaped Allen key. Do not use excessive force. Step 12 Check that the lever handles are correctly fitted for the hand of door.
- Page 7 Fit remaining spindle to inside - non code side. Step 9 Apply the front and back plates, with the neoprene seals in position, against the door, over the protruding ends of the spindle. Step 10 Fix the two plates together using the socket head bolts, starting with the top fixings. Ensure that the two plates are truly vertical and then tighten the bolts using the ‘T’...
- Page 8 Fire Kit Installation Instructions Take time to be precise and finish the job quicker. Installation holes must be drilled in exactly the correct positions and precisely at right angles to the door surface. Lock components must be vertically and horizontally accurate in relation to each other and to the door.
- Page 9 Step 7 Fit the latch support post to hole adjacent to A for a left hand door, and adjacent to B for a right hand door. Step 8 Screw the fixing posts (item 1 on page 13) into the front plate. Place the outer cover plate to the door with the inner cover plate (item 4) using the three fixing bolts (item 5).
- Page 10 Follow instructions as for non back to back versions substituting the backplate and handle 2, with the coded plate with the through fixing holes. Please note that each side may be coded with the same or different codes. B) The CL600 range is also available to work with most single point panic pads or bars. In this format the front code plate only is supplied with suitable fixing to connect to most single point panic pads and latches.
- Page 11 Keywords: Lock Locks Code CodeLock CodeLocks Program Programming Instruction Instruct Help Support Troubleshoot Troubleshooting Sequence Sequences Install Installation Parameters Settings Setting Parameter Setting Set up Mechanical CL600 600...
Need help?
Do you have a question about the CL600 Series and is the answer not in the manual?
Questions and answers